Solve the problem stated below. Use bond papers and black ball pen. Makeyour solution clear and clean. Draw the FBD.PROBLEMFigure:A homogeneous bar AC with negligiblemass is supported by a pin at A andcablecable BC, which carries a load of 20 kNas shown in the figure.a) Determine the force reaction at A, (PA).b) If the shearing stress is 80 MPa(double shear), determine the pindiameter at A.5 m.3 mpin4 mdouble shear60°20 kN

Answered: Image /qna-images/answer/ce8f42a5-2f6d-451c-87b3-6e619b537ce0.jpg

Solve the problem stated below. Use bond papers and black ball pen. Make your solution clear and clean. Draw the FBD. PROBLEM Figure: B A homogeneous bar AC with negligible mass is supported by a pin at A and cable BC, which carries a load of 20 kN cable 5 m. as shown in the figure. a) Determine the force reaction at A, (PA). b) If the shearing stress is 80 MPa (double shear), determine the pin diameter at A. 3 m pin 4 m double shear 60° 20 kN

Solve the problem stated below. Use bond papers and black ball pen. Make your solution clear and clean. Draw the FBD. PROBLEM Figure: B A homogeneous bar AC with negligible mass is supported by a pin at A and cable BC, which carries a load of 20 kN cable 5 m. as shown in the figure. a) Determine the force reaction at A, (PA). b) If the shearing stress is 80 MPa (double shear), determine the pin diameter at A. 3 m pin 4 m double shear 60° 20 kN

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 120 mm ×100 mm ×20 mm T section is used as a simply supported beam. The beam carries the applied eccentric load F of 120 KN at the position indicated in the Figure Q5. Start your calculations be setting an origin from the right most point on the cross section and determine the following : 5.1.The maximum compressive and tensile longitudinal direct stresses induced in the column. 5.2. Plot the stress distribution diagram and determine the position of the NA
bar AB is Q1) A homogeneous of M supported at either end by a cable as shown in figure beside. If the stress is not to exceed 75 MPa in bronze and 110 MPa in steel. And the diameter of bronze cable is 25 mm while for steel cable is 20 mm. Calculate the maximum safe mass M that can be carried by these cables. (1300) Bronze A 8m Steel
Problem 2. Each segment of bar ABC has length L. and shear modulus G and both segments have solid circular cross sections. Torque per unit length t(x) is applied between points B and C. The diameter of segment AB varies linearly from 2d at point A to d at point B. In terms of the given quantities, a) Find the torques at A and C. b) Find the twist angle os at point B. G 2d A -L d B G *(x) = to (²=²) ² C to x
Solve for the force in BD, vertical reaction at point C, horizontal reaction at point C, resultant of reaction at point C. What is the allowable tensile (normal) stress in member BD? What is the allowable shear stress in the pin at C? What is the required cross-section area for member BD? What is the minimum thickness t of member BD? What is the required SHEAR cross-section area at point C? What is the minimum diameter for the pin at C? (Solve for a value with the combination of mm and N)
The screw clamp shown in the figure applies a P = 500 N pressing force to the wooden blocks between the jaws. Itcase;a) Calculate the greatest tensile and compressive stresses occurring in the section a-a shown in the figure,b) show (draw) the distribution of normal stresses along the section height,c) Clamp material tensile safe tension em. = 50MPa and compressive strength em = 80MPa, then a-aWhat is the maximum compressive load (P) that can be applied without damaging the cross-section?
A uniform beam, 1.5 metre long, is suspended in a horizontal position by two vertical support rods as shown in the figure below. Rod A has a diameter of 12 mm and manufactured from steel with Esteel = 210 GPa. Rod B has a diameter of 16 mm and is made from copper with Ecopper = 105 GPa. This simply supported beam is to carry a motor vehicle engine and gearbox weighing 5,5 kN. Determine the distance ‘x’ from the left-hand support ‘A’ in order for the beam to remain in a horizontal position. Calculate the stress in each rod due to the applied load. Calculate the movement (extension) of the support wires under this 10 kN load. Will the rods be able to withstand the applied load? Motivate your answer.
Design of machine elements solve according to Khurmi Please write clearly
Gkuestrons T ØD VP The figure (not drawn to scale) shows a metallic cylindrical column submitted to a combined load: bending and torsion. The column contains an hemispherical groove of radius r, located at a distance L from the point of application of the loads. You are given the column diameter D = 68 mm, the groove radius r = 6 mm, the distance L= 200 mm, the bending load P=5 kN, and the torque T = 600 N.m. The material data are Young's modulus E = 122 GPa Shear Modulus G = 55 GPa Poisson's ratio v= 0.1 and Yield strength oy = 380 MPa. a) Write a numbered list of the calculation steps required to obtain the factor of safety in yielding based on the maximum distortion energy (Von Mises) criterion.
please solve step by step and correctly
ANSWER ALL FOR UPVOTE. INCOMPLETE WORK NO UPVOTE. THANK YOU
Please Give detailed Solutions and Correct Answers.Solve the problems below : (Use 4 decimal places for all your computations )