A bent pipe is attached to a wall with brackets as shown. A force of F= 235 lb is applied to the end of the tube with direction indicated by the dimensions in the figure. Determine the support reactions at the brackets B, C, and D. Model these brackets as journal bearings (only force reactions perpendicular to the axis of the tube) and neglect couple moment reactions. Assume the distance between the supports at B and C and the tube bends nearby are negligible such that the support at C' is directly above the support at D and the dimension g gives the distance between supports B and C. Enter your answers in Cartesian components. 2013 Michael Swanbom (сс x B BY NC SA a b с d h g M< Values for dimensions on the figure are given in the table below. Note the figure may not be to scale. Variable Value g 12.0 in 27.0 in 20.3 in 75.0 in 42.5 in 50.0 in The reaction at B is B = D The reaction at C is C = → The reaction at D is D = î+ î+ klb. ke lb. ke lb.

Q: Please build this on solidworks (create your own dimensions) and then provide a single drawing.…

A: Note: In the given drawing, the type of unit is not mentioned. So, we will use MMGS (millimeter,…

Q: 2. Sharp notches are often added to plastic food packages to help open them (along with arrows…

A: Detailed explanation:Sharp notches are a very good example of the functional features to the plastic…

Q: Let s be the length of each side of each tile in a cubic regular tiling of the sphere. What is cos…

A:

Q: 18. How far off from the center of the support is the center of the two holes in the bosses of the…

A: 18)    Distance=4.2-0.66                   =3.54 in

Q: I need answers to problems 4, 5, and 6 pertaining to the print provided.

A: In the given print the length and diameter of the part is to be calculated. Which is mentioned in…

Q: What are 1-, 2-, and 3-point perspectives? Draw cubes of different sizes using 1-, 2-, and 3-point…

A: Approach to solving the question: drawing, constructing of answer Detailed explanation: Examples:Key…

Q: Each cylinder in a four-cylinder car engine has a bore diameter of 63.53 mm and the stroke for each…

A: Consider a vehicle engine where number of cylinder are situated whose bore diameter is D and stroke…

Q: You do not need to provide Given, Assume, and Problem Type/Features for this  question. You just…

A: DefinitionStatic Equilibrium:If a body is at rest and experiences zero force or zero torque, this is…

Q: If the part was cut by this plane, what would the resulting remaining face look like?

A: Section planes in SketchUp cut a model along a plane so you may look within it without altering…

Q: Name 3 types of fits?

A: The different types of fits are : 1) Clearance fit 2) Interference fit 3) Transition fit

Q: for this question just sketch what it should look like:

A: Note : Window is denoted by point P

Q: Customary units by using the values listed for length and mass as defined values: Bending moment or…

A: As moment bending moment or torque has two variables, force and distance. So, M = F × r…… (1) The SI…

Q: Select the correct statement below regarding the two solid model parts shown. (A) (B) It is easiest…

A: In the figure two solid model parts are given. The extrusion is in which the two dimensional shape…

Q: Draw isometric view of casting, two views (FV and SV) of which are shown in figure in First angle…

A: Given question: Draw isometric view of casting, two views (FV and SV) of which are shown in figure…

Q: I have three parts that I need answered pertaining to the print provided below.   What material is…

A: To find the material specified for the part in the drawing, refer Title Block of the drawing.

Q: Select a material for a non-lubricated 25 pound block on a 30 degree steel incline to prevent…

A: To choose: To choose the correct option.

Q: An engineer first draws a circle in a plane and uses a tool to convert the circle to a disk that is…

A: SolidWorks is a 3D parametric design software that is used to design all sorts of 2D and 3D parts…

Q: Calculate each moment by multiplying each force with its distance to the reference point, and add…

A:

Q: Please turn this into 3d drawing, measurements are not important.

A: According to the question We need to find 3-D model of the drawing

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.