The screw clamp shown in the figure applies a P = 500 N pressing force to the wooden blocks between the jaws. It case; a) Calculate the greatest tensile and compressive stresses occurring in the section a-a shown in the figure, b) show (draw) the distribution of normal stresses along the section height, c) Clamp material tensile safe tension em. = 50MPa and compressive strength em = 80MPa, then a-a

Q: 100NM rod-1 100N rod-2 toost took 0.75 0.50 rod-1 0. rod-2

A:

Q: The screw clamp shown in the figure applies a P = 500 N pressing force to the wooden blocks between…

A:

Q: O MPa and an axial stress of 325 MPa that act on an element imposes a bending stress of 250 MPa and…

A: Tangential stress is .Axial stress is .Bending stress is .Torsional stress is .

Q: The three-member frame has original dimensions as shown in the figure. Elements F-D-B and A-B-E are…

A: givenElement FDB and ABE are rigid. so axial and flexure deeflection is zero.Area of CD…

Q: A mechanism used in printing machinery consists of a helical spring which is having a wire diameter…

A: Given data wire diameter (d) = 5 mm  OD of coil = 60 mm active coil = 12 Permissible shear stress =…

Q: AB brass and BC from aluminum bar ABC in shape composite rod was obtained. Composite rod B 0.05 mm…

A:

Q: AB and CD caps of the same material are tightly fitted on both ends of the 24 mm diameter AD steel…

A: Given:  E = 200 GPa LAB = 48 mm             LBC = 72 mm            LCD = 48 mm DAB  = 36 mm…

Q: 1. Question: With a pin on the AB beam A and a short lever BC as shown in the figure is supported.…

A: Given dataDiameter of the pins ar A,B and C d = 18mmLoad P = 30kNAngle α= 600Pin =ADetermine the…

Q: (b) a. A member ABCD is subjected to point loads as shown in figure Task 2.b. Calculate (i) Force P…

A:

Q: a. A member ABCD is subjected to point loads as shown in figure Task 2.b. Calculate (i) Force P…

A:

Q: The figure depicts a filleted cantilever bar. Find the largest normal stress for two cases: (a) the…

A: Given data: P=400 NM=10 N.mb=12 mm Need to determine the largest normal stress.

Q: 4 - A rectangular block is loaded with a 180 kN axial force and a moment M, as shown in the figure.…

A: Given data:-  Axial force =180 kN the maximum allowable tensile stress = 50 MPa To find:- the…

Q: 15 kN 2) Two objects are glued on the angled plane as shown in figure. If the ultimate stress for…

A:

Q: Calculate the maximum load (P) that can be supported by the knuckle joint that shown in the figure…

A: When it is required to join two rods which are placed under the tensile load and a small amount of…

Q: Problem 1: In the figure below a solid bar with a 1.00 in diameter is subjected to a bending moment…

A: Given data, Diameter of the solid bar, d = 1 in Twisting moment and bending moment are equal, i.e.,…

Q: P = 500 N pressing force to the wooden blocks between the jaws. It case; a) Calculate the greatest…

A:

Q: n the system in the figure, a) Since σy=450 MPa and the factor of safety is n=3, Find the…

A:

Q: Find the shear stress (in psi) exerted on the member shown in the figure if load (V) = 55 6b kips…

A: Problem 1: Given data: Load, V = 55.66 kips = 55.66×1000 = 55660 pounds. Area, A = 105.85 in2…

Q: The rigid beam is supported a pin connection at A and a cable BD at point the. Diameter of pin at A…

A: Note: As per our guidelines we are supposed to answer only the first 3 sub-parts. Kindly repost…

Q: The Uniform AB brass bar is fixed with support and pin as shown in the figure and has a rectangular…

A: Given data: (a) Write the expression for the critical load in the horizontal direction.

Q: For the rigid bar (AB) and rod (BC) system, the normal stress in rod BC can't exceed 30 ksi. The…

A:

Q: A bolted connection between a vertical column and a diagonal brace is shown in the figure below. The…

A:

Q: The pinned joint shown in the figure below is held by a ¾-in-diameter pin at A. If the force P = 5…

A: Given data :- diameter= 3/4 in Force(P) =5kips Thickness =1 in

Q: The screw clamp shown in the figure applies a P = 500 N pressing force to the wooden blocks between…

A:

Q: 3.33 For the plane trusses supported by the spring at node 1 in Figure P3-33 (a) and (b), determine…

A: As per our guidelines, we are supposed to answer only one question. Kindly repost other question as…

Q: The screwed clamp shown in the figure applies a P = 500 N pressing force to the wooden blocks…

A:

Q: Find the pull force P that will make the total elongation of the system 0.04 mm. b) Calculate the…

A:

Q: The steel bar in the figure has a diameter of 60 mm. As the shaft is loaded with the CDE rigid arm…

A: Given: Diameter of the steel bar is 60 mm. The loaded shaft is shown below:

Q: The round bar in the figure is made of steel (E-207 GPa). The load F has a magnitude of 100 N. You…

A: Young modulus of the material,(E)=207 GPa. Applied force (F)=100 N. Diameter of the shaft,(d)=20 mm.…

Q: A helical spring used in an automobile suspension is having a wire diameter of 7mm and an outside…

A:

Q: 1: The forces as given below are applied as shown in the figure. Fi=10 kN, F2=5 kN and F3=3 kN. The…

A:

Q: The figure shows a riveted lap joint with cover plates connecting two steel plates. Each rivet has…

A: Given data Diameter of rivet = 12 mm Thickness of plate = 15 mm Width of plate = 100 mm a) if load =…

Q: A helical spring used in an automobile suspension is having a wire diameter of 6mm and an outside…

A:

Q: The screw clamp shown in the figure applies a P = 500 N pressing force to the wooden blocks between…

A: