Rigid bar DB in the figure is supported at pin B by axial member ABC, which has a cross-sectional area of A₁ A₂ = 85 mm², an elastic modulus of E₁ E₂ 1450 MPa, and lengths of L₁ = 360 mm and L₂ = 640 mm. A load of Q = 270 N is applied at end C of member (2), and a load of P 1545 N is applied to the rigid bar at a distance of a 75 mm from pin support D and b = 35 mm from pin B. Determine the magnitudes of the downward deflections of: (a) pin B. (b) pin C. D Rigid bar a b B (1) (2) 4 L₂

Rigid bar DB in the figure is supported at pin B by axial member ABC, which has a cross-sectional area of A₁ A₂ = 85 mm², an elastic modulus of E₁ E₂ 1450 MPa, and lengths of L₁ = 360 mm and L₂ = 640 mm. A load of Q = 270 N is applied at end C of member (2), and a load of P 1545 N is applied to the rigid bar at a distance of a 75 mm from pin support D and b = 35 mm from pin B. Determine the magnitudes of the downward deflections of: (a) pin B. (b) pin C. D Rigid bar a b B (1) (2) 4 L₂

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A steel bar with a uniform cross section is fixed at both ends. A load P = 2.5 kips is applied at point C. The bar has a cross-sectional area of 8 in2.Calculate the reactions at joints A and B and the displacement at joint C. Assume that the modulus of elasticity E = 29,000 ksi.
QI A rigid bar ABCD is pinned at end A and supported by two cables of equal length at points B and C.The cable at B has nominal diameter D=12 mm and the cable at C has nominal diameter D= 20 mm. IF a load P=30 -dc KN acts at end D of the bar. What is the stresses for the cables at B and C if the temperature rises by 60°C. (E = 140 GPa and a=12 x 10/°C for both cables). -26 to -26- P
The support in the figure below consists of a C83400 copper bar inserted into a 304 stainless steel tube. loading there is a 1.0 mm clearance between the upper end of the copper bar and the steel pipe as shown in the figure. Determine the largest load P that can be applied to hard disk A so that both the copper bar and steel tube remain in the elastic regime.
2.2-4 A steel cable with a nominal diameter of 25 mm (see Table 2-1) is used in a construction yard to lift a bridge section weighing 38 kN, as shown in the figure. The cable has an effective modulus of elastic- ity E = 140 GPa. (a) If the cable is 14 m long, how much will it stretch when the load is picked up? (b) If the cable is rated for a maximum load of 70 kN, what is the factor of safety with respect to failure of the cable? ▬▬
The aluminum bar ABC has a cross-sectional area of 20 mm2 is supported by a pin at A and a steel wire at B. If P = 50 kN calculate the horizontal displacement of P. The cross- sectional area of the wire is 1.75 mm2, modulus of elasticity of aluminum is 70 GPa and the modulus of elasticity of steel is 200 GPa. D 90 cm 90 cm B 180 cm Ale 120 cm
A solid steel bar of diameter di = 1.4 in. is enclosed by a steel tube of outer diameter d3 = 2.25 in. and inner diameter d2 = 1.9 in. (see the figure). Both bar and tube are held rigidly by a support at end A and joined securely to a rigid plate at end B. The composite bar, which has length L = 26 in., is twisted by a torque T = 5,100 lb-in. acting on the end plate. Tube A Bar End plate (a) Determine the maximum shear stresses T1 and T2 in the bar and tube, respectively. Round your answers to the nearest whole number. T1 = psi T2 = psi (b) Determine the angle of rotation (in degrees) of the end plate, assuming that the shear modulus of the steel is G = 11.5 × 10° psi. Round your answer to three decimal places. (c) Determine the torsional stiffness kT of the composite bar. Round your answer to the nearest whole. [Hint: Use equations below to find the torques in the bar and tube.] T = T GIp, + G2IP, kT = k-in.
3. The bar shown below is composed of two pieces, AC and CD. The bar is attached to the wall at point A. The length L = 10 in. The cross sectional areas are: AAC = 4 in? and AcD = 2 in?. The Young's Moduli are: EAC =20 Msi and Ecd= 15 Msi Two forces are applied at points B and D: PB = 50 kips and PD = 20 kips. Determine: (a) the reaction force at A (specify –→ or +) and (b) the deflection of point D (specify → or +). (Hint for (b): Think about how many pieces you must subdivide the rod into.) Ans: RA = 30 kips (+), dp = 7.9167×10-3 in (E) A В C D Pp L 2L L
The assembly consists of two-rod brass C83400 copper alloy rods AB and CD of diameter 30 mm, a stainless 304 steel alloy rods EF and FG of diameter 40 mm, and a rigid cap H as shown in Figure 2. Neglect the size of the collar at F. Assume that the modulus of elasticity Esteel = 200 GPa and Ebrass = 101 GPa. If the force, P = 5 kN, (a) If the horizontal displacement of end G of rod FG is 0.6 mm, determine the new magnitude of P.
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure. One load of P=33P=33 kipskips is applied to the assembly at A, two loads of Q=30Q=30 kipskips are applied at B, and two loads of R=35R=35 kipskips are applied at C. The normal stress magnitude in aluminum rod (1) must be limited to 1717 ksiksi. The normal stress magnitude in steel rod (2) must be limited to 3030 ksiksi. The normal stress magnitude in brass rod (3) must be limited to 2121 ksiksi. Determine the minimum diameter required for each of the three rods.
The composite shaft, consisting of aluminum, copper, and steel sections, is subjected to the loading shown. The cross-sectional areas of sections AB, BC, and CD are AAB = 0.09 in², ABC = 0.15 in², and Acp = 0.05 in², respectively. The modulus of elasticity for each section are shown in the figure. Neglect the size of the collars at B and C. (Figure 1) Figure Aluminum Eal = 10(10³) ksi 2.00 kip -18 in- Copper Ecu = 18(10³) ksi 3.50 kip 13.50 kip -12 in- Steel Est = 29(10³) ksi 1.75 kip 1.75 kip -16 in- 1.50 kip 1 of 1 Part A Determine the normal stress in section AB. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. Part B Determine the normal stress in section BC. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. OBC = Submit Part C OCD =…
A vertical load P is applied at the center B of the upper section of a homogeneous frustum of a circular cone of length L, minimum radius rB, and maximum radius rA, as shown in the figure below. It is made of a material with a modulus of elasticity E. Neglect the effect of its weight. Use the following values: rA = 2 in, rB = 0.5 in, L = 3 ft, E = 30 (103 ) ksi, and P = 1800 lbf. Discretize the original geometry into three equal-length finite elements and (a) Compute all the nodal displacements. (b) Compute all the element axial stresses. (c) Plot the displacement field from the finite element method solution. (d) Plot the axial stress field from the finite element method solution.
The assembly consists of two-rod brass C83400 copper alloy rods AB and CD of diameter 30 mm, a stainless 304 steel alloy rods EF and FG of diameter 40 mm, and a rigid cap H as shown in Figure 2. Neglect the size of the collar at F. Assume that the modulus of elasticity Esteel = 200 GPa and Ebrass = 101 GPa. If the force, P = 5 kN, (a) Sketch the free body diagram and calculate the internal forces acting in each section of the rod. (b) Determine the average normal stress developed in rods FG, EF and AB. (c) Determine the average normal strain in the rod of AB.(d) If the horizontal displacement of end G of rod FG is 0.6 mm, determine the new magnitude of P.