.. A factory has two machines, A and B. Machine A produces 60% of the parts, while Machine Bproduces 40%. Machine A produces defective parts 5% of the time, while Machine B produces defectiveparts 10% of the time. A randomly selected part from production is inspected.a) Draw a tree diagram to represent the probability of getting a defective part.b) What is the probability that a randomly selected part is defective?c) If a part is found to be defective, what is the probability it came from Machine A?

Answered: Image /qna-images/answer/2da5d8d1-d883-415b-9440-bdbd9a10b11e.jpg

Answered: .. A factory has two machines, A and B.…

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter27: Single-phase Transformers

Section: Chapter Questions

Problem 6RQ: What is a disadvantage of an autotransformer?

See similar textbooks

Similar questions

a.it a Moore machine or Mealy? Why? b. Create the next-state table. Show your work. Label your columns. c. Question b's table and question c is attached from the picture below
Could you explain how these factors cause the degradation?
With the aid of well labeled diagrams, explain the principle of operation of: a. a pyranometer. b. a wind turbine, from resource to electrical power
A Factory produces light bulbs from two different machines: Machine A and Machine B. The probability that a randomly selected light bulbs is from Machine A is 60%, and the probability that a light bulb is defective is 5%. Suppose that probability that a light bulb is defective given that it was made by Machine A is 0.05. Similarly, the probability that a light bulb is defective given that it was made by Machine B is 0.03. Are the events “the light bulb is from Machine A” and “the light bulb is defective” independent?
Select the best answer for the question. 4. Look at the drawing shown in the figure above. When you see this drawing in a schematic diagram, you should recognize that it represents a/an O A. step-up transformer. O B. inverter. C. bridge rectifier. OD. thermal relay.
What is a disadvantage of an autotransformer?
Q1. Draw flowchart to find the average of 10 positive numbers. [Hint: Read the number in a loop, add them if it is positive and then find average] Q2. Draw flowchart to read 5 numbers from a user and then find the second largest number of them.
1.A. You've assembled the following components to join two copper conductors: a mould, powdered copperoxide, powdered aluminum, and an igniter. With these components, which of the following processes willyou use to connect the conductors?A. Exothermic weldingB. Irreversible compression groundingC. Mechanical groundingD. Thermal cycling 1.B. Two electricians are discussing voltage ratings. Electrician A says that a motor that's installed 40 feetfrom a power source will show a lower applied voltage than a motor that's installed 20 feet from the samepower source. Electrician B says that an exact voltage of 240 V must be applied to a motor that's rated at240 V. Who is correct?A. Neither Electrician A nor Electrician B is correct.B. Only Electrician A is correct.C. Only Electrician B is correct.D. Both Electrician A and Electrician B are correct.
Define slew rate with the formula and its unit.
A JFET is a driven device .... ... Select one: a. none of the above b. both current and voltage C. current d. voltage
Please answer fast in 30-60 minutes an u can send the solution im very needed thank u
How is induction applied? For each , give details of how induction is achieved?

SEE MORE QUESTIONS

Recommended textbooks for you

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS