Open Ended Lab Design an electrical network using Resistors, inductors and capacitors, voltage source and current source that achieves the following: 1. A specific input impedance (10ohm+j5ohm at 1kHz) 2. A specific output range (5-12V across a load of 50ohm 3. The ability to filter out frequencies above or below a given cutoff e.g low pass filter with a cutoff at 1KHz.

Open Ended Lab Design an electrical network using Resistors, inductors and capacitors, voltage source and current source that achieves the following: 1. A specific input impedance (10ohm+j5ohm at 1kHz) 2. A specific output range (5-12V across a load of 50ohm 3. The ability to filter out frequencies above or below a given cutoff e.g low pass filter with a cutoff at 1KHz.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Define briefly the terms used in filter below, a) pass band b) attenuation band c) Cut off frequency (-3db frequency)
What is lead compensator? Draw its circuit diagram and derive the expression for the transfer function of lead compensator. Solve it fast fast plz
5.q4.pt1.t4
Answer True or False, then correct errors or explain if any: 1. The term pole in filter terminology refers to the feedback circuit. 2, A voltage shunt feedback with Ai-10, A-20, p 0.45, then Aif will be 1. 3. The integrator Op-Amp circuit can be used to produce square waves. 4. The equivalent circuit of the crystal oscillator is series and parallel (R, C) components. 5. The transistor in a class A power amplifier conducts for the entire input cycle. 6. Bypass capacitors in an amplifier determine the low and high-frequency responses. 7. The midrange voltage gain of an amplifier is 100. The input RC circuit has a lower critical frequency of 1 kHz. The actual voltage gain at f- 100 Hz is 100. 8. The Bessel filter types produce almost ripple frequency response. 9. RC phase shift oscillators are based on both positive and negative feedback circuits. 10. In a high-pass filter, the roll-off region occurs above the critical frequency,
What is a bandpass filter? How is its bandwidth defined?
For the filter: a) Determine type of filter and the cut-off frequency (Fc). Determine the peak voltage at the cut-off frequency (Fc). b) Find GAIN (Vo/Vi) at f = .1*Fc . Find GAIN (Vo/Vi) at f = 10*Fc . c) Determine the frequency at which GAIN = .4 (i.e., Vo = .4*Vi) . Draw the “Frequency Response Plot” in “Log-Log” format .
What is the function of a low pass filter? Draw a diagram of a simple low-pass filter using a capacitor and a resistor.
a) What kind of filter is this? Be as detailed as you can be. b) What is the equation for the transfer function Vo/v; of this filter? c) What is the equation for the break frequency? Vi R₁ www www R₂ VOUT
Can you check if its correct: Draw and label the Frequency Response Plot of "GAIN vs Frequency" specifying the GAIN at: a. f = .1Fc --> gain = 9.95 b. f = Fc --> gain = 7.071 c. f = 10Fc --> gain = 0.995
. Design a low-pass active filter of cut-off frequency 100 kHz and gain 32 dB.(assume C = 0.1nF)
How can I design an active filter circuit (just the low pass) using resistors, capacitors, and op-amps that will implement the transfer function. You will need to factor the function into cascade functions in order to make this easier. I jus want the drwan design with a litte explanation if possible.
2. a) Consider the circuit shown in figure 3. i) Determine what type of filter is shown in Figure 3 i) Calculate the corner or cutoff frequency. Take R = 4 k &, L= 2 H, and C= 1 uF. R Figure 3 b) Describe the possibility of building a second order filter with only resistors and capacitors? and design the cutoff frequency of second order filter for low pass filter (Expected: Describe the possibility , design the second order filter for low pass filter circuit and design the cutoff frequency as equation only).