4. Given the following Active Filter circuit: Vin= .6 sin wt R2 w R1 w 2ΚΩ Rf ww 18ΚΩ + VCC (+12v) 5.0V U1 + 741 Vo 10ΚΩ C1 .001592μF 5.0V VCC (-12v) 1. Determine the following: a. The cutoff frequency (Fc) b. The Gain of the amplifier at a frequency equal to 100 Hz & The GAIN of the amplifier at the cutoff frequency C. The peak-peak amplitude of Vo at a frequency equal to 100 Hz

4. Given the following Active Filter circuit: Vin= .6 sin wt R2 w R1 w 2ΚΩ Rf ww 18ΚΩ + VCC (+12v) 5.0V U1 + 741 Vo 10ΚΩ C1 .001592μF 5.0V VCC (-12v) 1. Determine the following: a. The cutoff frequency (Fc) b. The Gain of the amplifier at a frequency equal to 100 Hz & The GAIN of the amplifier at the cutoff frequency C. The peak-peak amplitude of Vo at a frequency equal to 100 Hz

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Quarter-bridge strain gauge circuit R2 + Vout – strain gauge E R4 The Wheatstone bridge shown has the following values: E = 15 V R1 = 100 2 R2 = 100 2 R3 = 100 2 R4 = 100 2 (strain gage) If an applied compressive force changes the strain gage to 88.89 2, what is the output voltage? No label, no unit, just the number.
bro pls solve & show all steps for a beginner try to write some explanation pls..
3-terminal circuit element C is modelled with the following terminal equations and terminal graf which is shown in the figure. Find the Thevenin equivalent with respect to the terminal a andb.
4S2 www 32 Q.1: For the circuit shown: 1. Write J22 the voltage equations w.r.t currents. J312 J40 V: 2. Find the value of (V,N2) when ,=0? 3. Find the value of (V2/N1) when I2=0? (Ans.: 0.4236.87° & 0.4253.13°
Registration no is 219.
Can you answer these using your own words.??
D4
control systems
PROBLEM [ B4]: Two resistors R, and R, are connected in parallel in an electric circuit. If the resistance R, is changed from 16 to 16.2 ohms and R, is changed from 28 to 27.8 ohms, find the absolute change, relative change and percentage change in the total resistance R.
B) Page < of 4 并7 OLYMPIC COLLEGE Mar Find the total resistance for the resistor circuit shown in Figure P14. 3 k2 500 2 75 0 4.7 kn 3.3 k2 300 2 150 2 2.2 k2
(a) A d.c bridge based on strain gauge sensor is used to measure the vehicle weight. The vahes of Vac =5 V, R1, R2, and R3 is 150 k2. The vahue of stram gauge, R4 before loaded is 150 k2. Before the measuurement, a standard load with weight of 6000 kg is used for calbration. The galvanometer, I, is flowed about 2.25 uA. Analyse the crcuit to determine vahues of R V and R when it is loaded. Assume the vahue R of galvanometer is zero. R1 R3 Vác R2 Figure Q4
Although we are given the restrictions on Kd and Kp, explain how we arrived at that conclusion and show all work necessary to arrive at the given solution for each restriction.