CMP 210 HW 10

Q1: Select the correct answer. up to A. Resilience is the energy absorbed by the material a. yield. b. ultimate sensile stress. c. fracture. B. The grain boundaries are a. less chemically active than grains themselves. b. the regions of orientation mismatch of the neighbouring grains. c. classified as linear defects. C. All polycrystalline materials are considered as isotropic because a) they have crystallographic direction-mechanical properties independence relation b) all the crystals' orientations are the same c) the random direction of many grains cancels the anisotropic effect D. Dislocations slip process in metallic crystalline materials a) is essential to explain why the metals exhibit much lower strength than that theoretically predicted based on metallic bonding. b) makes metals and alloys brittle. c) cannot be used to control the mechanical properties of metallic materials E. The atomic stacking ABCABCABC is for d) FCC crystal structure e) BCC crystal structure f) HCP crystal…

4

If the cooling system operates above 100 degrees Celsius how should the cooling system, cooling fans, and thermostat be tested? (80 - 100 Words)

QUESTION 1 Match each of the following terms to the phrase that describes it. Answers are used only once. * Technique that might be used to spread components apart. A. Diagram B. CAGE * Parts list column for government number. C. Inseparable D. Application E. Exploded F. Installation + Name of a block with a Used On column. + Could be called Notes. Parts list column related to purchased parts. G. Procurement * Type of assembly most likely made with symbols. H. Find + Welding drawing, for example. I. Zone J. Remarks * Type of assembly most likely to be pictorial. + Parts list column to help find a part on the page. Often the first column in basic parts list.

I need answers to parts 7, 8, and 9, pertaining to the print provided.

I need answers to parts 13, 14, and 15, pertaining to the print provided.

A symbol used to identify a physical feature of a part as a datum feature is called a: O Reference feature O Feature control frame Feature of size O Datum feature symbol

these are shot questions please answer the all questions it's important for me

Q-1A) Identify if TRUE or FALSE, give an explanation for the FALSE ones only). a. If a homogenous piece of rock is cut into two pieces, then each one will have the same formation factor. h Micro-resistivity log can be used in oil-based mud and water-based mud systems. L. In a water bearing formation, Ro is equal to the Rt. d. A high GR value always indicates the presence of shale. e One of the most important application of the SP log is to measure the formation permeability. L Caliper log shows a smaller reading that the bit size for evaporite (Salt) layers. g. If the micro-Inverse and micro-Normal logs exhibit positive separation, the permeability of the formation is small. b. A reverse/positive SP deflection occurs when Rmf< Rw. i Water Saturation is defined by the ratio of water volume to the bulk volume of a rock. i The higher formation porosity, the larger invasion diameter. k. Induction log measures the formation resistivity. L Well-logging measurements are recorded while puling…

Partial Question 9 Which choices are correct explanations about the scanning electron microscope (SEM)? (Select all that apply.) Visible light is the main light source. The microscope can investigate non conductive samples as good as the conductive ones. Samples need to be polished. The condensed beam does not pass through the specimen, but is reflected from a surface of the specimen and was collected to obtain the picture. Useful resolution range is much wider than the optical microscopes.

Assignment Booklet 4B ce 24: Module 4 6 Identify the safety features shown in this automobile from the following list. Place your answers in the blank spaces given. • bumper • hood • crumple zones • roll cage • side-impact beams Return to page 75 of the Student Module Booklet and begin Lesson 2. For questions 7 to 10, read each question carefully. Decide which of the choices BEST completes the statement or answers the question. Place your answer in the blank space given. 7. According to Transport Canada, how many Canadians owe their lives to seat belts between 1990 and 2000? A. 690 В. 1690 С. 1960 D. 11 690 8. By what percent is the webbing of a seat belt designed to stretch to help absorb energy in a collision? A. 0% B. 5-10% C. 10-15% D. 15-20% 9. What is the level of seat belt use in Alberta? A. 90% В. 70% С. 50% D. 30% Teacher

It says surface Temperature is not 125.49oC (look at picture I attached). What would be the correct value? Thank you.

Don't provide wrong answer since it's Important one.