MET330L 5.2 Lab

Use excel to make a best curve fit to demonstrate the relationship between ground speed and airflow and ground speed cabin T.

Qu. 7 The v -t graph of a car while travelling along a road is shown. Draw the s -t and a -t graphs for the motion. I need to draw a graph and I need to show all work step by step please do not get short cut  from dtna

QUESTION 3 The following conversion equivalents are given: 1 gal 231 in 1 ft 12 in 1 min 60 s A pipe delivers water at the rate of 51 gal/min. The rate in ft3/s, is closest to: 0.083 0.11 0.093 0.073 0.10

1) Pitot tube can be used to measure the flow velocity. The equation can be derived from Bernoulli Equation. True or False 2) Which of the following statement is NOT correct about piping network? a) In parallel pipes, the flow rate is proportional to its diameter and inversely proportional to its length and friction factor. b) When analyzing the piping network, conservation of mass throughout the system must be satisfied. c) In piping systems with pumps, the Bernoulli equation should be corrected by introducing a kinetic energy correction factor. d) The algebraic sum of head losses for all loops equal to zero. 3) The EGL is always a distance V2/2g above the HGL. True or False

A) Calculate by hand the net head delivered and the efficiency of the pump at flow rate of 63 L/s. B) Use excel sheet and its formula to solve the equations and plot the pump head, power input, and efficiency versus the pump flow rate

56.0 mL of two different liquids are poured through a funnel with a narrow exit tube, and the time for all of the liquid to flow through is recorded. Here are some results: time to flow through funnel trial Liquid X Liquid Y 1.60 s 3.62 s 1.52 s 3.44 s 1.44 s 3.56 s Note: the two liquids have the same density. Which statement below is true about these liquids based only on the data in the table? O The intermolecular forces in liquid X are stronger than those in liquid Y. The boiling point of liquid X is higher than the boiling point of liquid Y. The viscosity of liquid X is greater than the viscosity of liquid Y. The surface tension of liquid X is greater than the surface tension of liquid Y. The viscosity of liquid X is less than the viscosity of liquid Y. 3.

Use at least 4 significant figures throughout the entire problem. 9.80m/s2 for the acceleration due to gravity. Do not use 10 m/s2 for the acceleration due to gravity.

01.0 3 Cylindrical tanks are filled with a liquid as shown below. a)( )Calculate the time to completely drain each tank. Neglect viscous effects. Provide your answers in units of seconds to one decimal place. b) (C ) Determine which tank completely drains the fastest. Rank the three tanks in terms of draining timne: fastest to slowest. Tank 1 Tank 2 Tank 3 20 kPag 20 kPag D= 40 mm D,= 40 mm D, = 40 mm Water 15°C Kerosene SG 0.820 2.0 m Water 15°C O kPag O kPag o kPag D,= 2 mm D. =2 mm D,= 2 mm

show working

Convert the following using the conversion table attached.

Please don't provide handwritten soution ....

I already have the answer and provide it. Show work please

Solve in MS excel using bisection and Newton-Raphson method! Show all steps in excel

C)If both cyclists have 170 mm cranks on their bikes, what will be the mechanical advantage (considering only the movement of the feet with a constant force for walking and riding), in percent, that each rider will have achieved over walking the same distance? (This can be found by dividing the distance wallked by the distance the feet move in riding.)

Question 2 Figure 3 shows the numerical solution of the advection equation for a scalar u along x at three consecutive timesteps. 1.0 0.8- 0.6- 0.4- 0.2- 0.0- -0.2- -0.4- -0.6 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 Figure 3: Advection equation, solution for three different timesteps. a) Provide an explanation what conditions and numerical setup could explain the curves. Identify which of the three curves is the first, second and third timestep. b) Consider explicit schemes with central and upwind discretisations. Explain how each of these candidate discretisations could produce the behaviour shown in Figure 3. c) Determine the CFL number that was used in the simulation for each of the candidate schemes for all possible updates. Assume that the timestep and mesh-width used are constant. Read the data to two digits of accuracy from Figure 4 shown at the end of the question, which is an enlarged version of Figure 3. Demonstrate your method and input data for one calculation, but then use a…

need correct ans or leave

Show the solution and final answer in two decimal.

Suppose you make the following sequence of measurements for the segments in laying out a compressed air line: 4.61 m 211 m 0.500 m What should be the reported total length of the air line?   options:   216.1   216.110   220   216.11   216

A) Perform an analysis of the stenosed artery (diameter D and length L)using the Bernoulli equation to determine an expression for the pressure drop across the segment of artery for a blood flow rate (Q). Create a well labelled diagram indicating the area of analysis and variable names and state all relevant assumptions made in your analysis. You snould assume that the stenosis creates a rapid narrowing of the artery, and that friction is not negligible. B) Explain how your analysis would change following insertion of the stent.

Flow Speed in a Channel The speed of water flowing in achannel, such as a canal or river bed, is governed by theManning Equation,

8.) please help

A chunk of log floats in water, with 2 inches protruding above the surface. The object is put in oil having a SG of 1.35 , it then projects 3.0 inches above the surface. Find the SG of the log. Select the correct response: 0.542 0.659 0.715 0.445 0.224 0.342