QUESTION 3The following conversion equivalents are given:1 gal 231 in 1 ft 12 in 1 min 60 sA pipe delivers water at the rate of 51 gal/min. The rate in ft3/s, is closest to:0.0830.110.0930.0730.10

Answered: water at the rate of 51 gal/min.

Engineering

Mechanical Engineering

water at the rate of 51 gal/min.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 1.A liquid refrigerant (sg = 1.080) is flowing at a weight flow rate of 23.0 N/h. Required…

A: As per our guidelines we are supposed to solve only one question if multiple questions are asked .…

Q: If the net positive suction head (NPSH) requirement for the pump is not satisfied, then, Select one:…

A: ANSWER = (a) cavitation will formed.

Q: The pump is used to increase the pressure of water from 100 kPa to 900 kPa at arate of 160 L/min. If…

Q: VISSA TA py w..... 14.40 What type of pump should be used to pump water at a rate of 10 cfs and…

Q: Provide one question and its solution involving an external flow of fluid .

Q: Water is supplied at a rate of 3000 litres per minute from a height of 4 metres to a hydraulic ram…

Q: Measure the volumetric flow rate of water coming out of a faucet. Also determine the average…

A: given: Measure the volumetric flow rate of water coming out of a faucet. Also determine the average…

Q: Thirty (30) liters/second of stream water must be pumped up a vertical height of 12 meters to…

A: Water flow rate, Q=30 Lit/s Water pumped to vertical height, H=12 m Pump efficiency, ηpump=62% Motor…

Q: Hydraulic fluid flows at velocity of 200 in/min through a conduit with an internal diameter of 2…

A: The objective of this question is to calculate the flow rate of hydraulic fluid in gallons per…

Q: 1. Water is flowing from the inlet to the exit. At the inlet the speed is 20m/s. Calculate (a) the…

A: Given data :Speed at inlet Inlet diameter Exit diameter

Concept explainers

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Please provide complete solution and diagram. An air compressor takes air and discharges it to 200 psi. If the volume flow of the discharge is 1.5 m3/sec, determine the capacity of the compressor in liters per sec. A. 9570.23 li/s C. 9680.24 li/sB. 8680.25 li/s D. 9750.24 li/s
QI) The vapour pressure, p, of nitric acid varies with temperature as follows: 0 20 40 1.92 6.38 17.7 27.7 62.3 89.3 124.9 170.9 50 70 80 90 100 p/kPa What are : (a) the normal boiling point (b) the enthalpy of vaporization of nitric acid? Q2) Calculate the melting point of ice under a pressure of 50 bar. Assume that the density of ice under these conditions is approximately 0.92 g cm and that of liquid water is 1.00 g em'. Q3) An open vessel containing (a) water, (b) benzene, (e) mercury stands in a laboratory measuring 5.0 m x 5.0 m x 3.0 m at 25°C. What mass of each substance will be found in the air if there is no ventilation? (The vapour pressures are (a) 3.2 kPa, (b) 13.1 kPa, (c) 0.23 Pa.)
1) Pitot tube can be used to measure the flow velocity. The equation can be derived from Bernoulli Equation. True or False 2) Which of the following statement is NOT correct about piping network? a) In parallel pipes, the flow rate is proportional to its diameter and inversely proportional to its length and friction factor. b) When analyzing the piping network, conservation of mass throughout the system must be satisfied. c) In piping systems with pumps, the Bernoulli equation should be corrected by introducing a kinetic energy correction factor. d) The algebraic sum of head losses for all loops equal to zero. 3) The EGL is always a distance V2/2g above the HGL. True or False
56.0 mL of two different liquids are poured through a funnel with a narrow exit tube, and the time for all of the liquid to flow through is recorded. Here are some results: time to flow through funnel trial Liquid X Liquid Y 1.60 s 3.62 s 1.52 s 3.44 s 1.44 s 3.56 s Note: the two liquids have the same density. Which statement below is true about these liquids based only on the data in the table? O The intermolecular forces in liquid X are stronger than those in liquid Y. The boiling point of liquid X is higher than the boiling point of liquid Y. The viscosity of liquid X is greater than the viscosity of liquid Y. The surface tension of liquid X is greater than the surface tension of liquid Y. The viscosity of liquid X is less than the viscosity of liquid Y. 3.
Please don't provide handwritten solution ...
Convert the following using the conversion table attached.
Calculated f) as 4690 l/s, g) as 1.29m/s and h) as 293.89 bar. How to calculate i) average velocity of flow at cross section 4
HELP. im confused between choosing foward interpolation or newtons divided difference formula, please send the entire solution
Solve the ff. The discharge pressure of an air compressor is 5 times the suction pressure. If the volume flow at suction is 0.7m3/s and discharge volume flow of 0.2217m3/s, what is the compressor power(hp) if suction pressure is 100kpa. Ans. 191.72 A double acting air compressor has a cylinder dimension of 50cm x 60cm, 750rpm will have a volume displacement (m3/s) of: Ans. 2.945 A pump has a specific speed of 45 and 600rpm when it delivers 0.01m3/s. Find the head developed by the pump in ft. Ans. 926.07
3. A pump discharges 126 liters per second of brine (sp.gr.1.20). The pump inlet, 304.8 mm diameter, is at the same level as the outlet, 203.2 mm in diameter. At the inlet, the vacuum is 152.4 mm Hg. The center of the pressure gauge connected to the pump discharge flange is 122 cm. The gauge reads 138 KPag. For a pump efficiency of 83%, what is the power output of the motor? 122 cm. PUMP
Project 1 100 20. 150 200 250 300 350 400 450 500 550 600 650 CUPONTHFC-134a 700 200. 0.0016 1- 00018 10. Pressure-Enthalpy 0.0014 000124 0.0020 8. 0.0030 100. 80. 6. Diagram volume-0.0040 mikg (SI Units) 0.0060 0 0080 0.010 60. 40. 2. 0.015 0 020 20. 0030 0.8 0.040 10. 8. 0.6 0.060 0.4 6. 0 080 010 0.2 0.15 020 2. 0.1 0.08 0.30 0.40 1. 0.8 0.06 060 0.04 0.6 O80 1.0 0.4 0.02 1.5 20 0.2 0.01 100 150 200 250 300 350 400 450 0.1 700 500 550 600 650 Enthalpy (kJ/kg) Refrigerant HFC-134a as the working fluid - Ideal cycle operation condition is assumed Cycle is operated at high pressure line of 0.8 MPa Cycle is operated at low temperature line of – 10° C - Flow rate is 0.1 kg/sec The head of the department in the company that you are working in asked you to make use of pressure - enthalpy chart provided for HFC-134a refrigerant a. Construct didactic sketches, showing the operating principles of a refrigeration system Pressure (bar) 4. -Dozz -auneadu H 061 ta 091 Ti 1000 06 0 - --- 99'O 09…
Hey Can someone help with these questions in the pictures explanation and answer short and great please. Thank u