A 15° wedge is forced under a 50-kg pipe as shown. Knowing that the coefficient of static friction at both surfaces of the wedge is 0.20, determine the largest coefficient of static friction between the pipe and the vertical wall for which slipping will occur at A.
Fig. P8.64 and P8.65
Find the largest coefficient of static friction between the pipe and the vertical wall for the condition.
Answer to Problem 8.65P
The largest coefficient of static friction between the pipe and the vertical wall is
Explanation of Solution
Given information:
The mass of the pipe is
The value of angle
The coefficient of static friction at all surfaces is
Calculation:
Find the weight (W) of the pipe using the relation.
Here, the acceleration due to gravity is g.
Consider the acceleration due to gravity is
Substitute 50 kg for m and
Show the free-body diagram of the pipe as in Figure 1.
Find the friction force at point B using the relation.
Here, the normal force at point B is
Find the normal force at point B by taking moment about point A.
Substitute 490.5 N for W, 0.20 for
Find the normal force at point A
Substitute 0.20 for
Find the friction force at point A
Substitute 490.5 N for W, 0.20 for
Find the coefficient of static friction at point A
Substitute 137.507 N for
Therefore, the largest coefficient of static friction between the pipe and the vertical wall is
Want to see more full solutions like this?
Chapter 8 Solutions
VECTOR MECH...,STAT.+DYNA.(LL)-W/ACCESS
- 8.50 and 8.51 Two 6° wedges of negligible weight are used to move and position the 900-kg block. Knowing that the coefficient of static friction is 0.30 at all surfaces of contact, determine the smallest force P that should be applied as shown to one of the wedges. Fig. P8.50 900 kgarrow_forwardEnd A of a slender, uniform rod of length L and weight W bears on a surface as shown, while end B is supported by a cord BC Knowing that the coefficients of friction are µs = 0.40 and µk = 0.30, determine (a) the largest value of 6 for which motion is impending, (b) the corresponding value of the tension in the cord.arrow_forwardA lever AB of negligible weight is loosely fitted onto a 2.5-in.-diameter fixed shaft. Knowing that the coefficient of static friction between the fixed shaft and the lever is 0.15, determine the force P required to start the lever rotating counterclockwise.arrow_forward
- W = 10 N B W=10 N PROBLEM 8.36 Two 10-N blocks A and B are connected by a slender rod of negligible weight. The coefficient of static friction is 0.30 between all surfaces of contact, and the rod forms an angle = 30°. with the vertical. (a) Show that the system is in equilibrium when P=0. (b) Determine the largest value of P for which equilibrium is maintained.arrow_forwardThe foot of a uniform ladder, of length 2a and weight W, rests on rough horizontal ground and the top of the ladder rests against a smooth vertical wall, The ladder makes an angle of 60° with the horizontal. A man of weight 4W climbs up the ladder. Given that the ladder begins to slip when the man has climbed two-thirds of the way up the ladder, find (a) the coefficient of friction between the ladder and the ground, (b) how far a boy of weight 2W can climb up the ladder before it slips.arrow_forwardthe coefficient of static friction is the same between block B and the horizontal surface and between the rope and support c. knowing that Wa = Wb, determine the smalles value of static friction for which equilibrium is maintainedarrow_forward
- A lever AB of negligible weight is loosely fitted onto a 2.5-in.-diameter fixed shaft. Knowing that the coefficient of static friction between the fixed shaft and the lever is 0.15, determine the force P required to start the lever rotating counterclockwise.arrow_forwardQuestion: An 18-kg mass is hung from a lever which rests againsta 10 degree wedge at A and is supported by a frictionless pin at C.Knowing that the coefficient of static friction is 0.25 at bothsurfacees of the wedge and that for the position shown the springis stretched 100 mm, determine (a) the magnitude of the force P forwhich motion of An 18-kg mass is hung from a lever which rests againsta 10 degree wedge at A and is supported by a frictionless pin at C.Knowing that the coefficient of static friction is 0.25 at bothsurfacees of the wedge and that for the position shown the springis stretched 100 mm, determine (a) the magnitude of the force P forwhich motion of the wedge is impending, (b) the components of thecorresponding reaction at C.arrow_forwardA 15° wedge is forced under a 50-kg pipe as shown. Knowing that the coefficient of static friction at both surfaces of the wedge is 0.20, determine the largest coefficient of static friction between the pipe and the vertical wall for which slipping will occur at A.arrow_forward
- Solve Prob. 8.62 assuming that the wedge is to be forced under the machine base at B instead of A.(Reference to Problem 8.62):A 5° wedge is to be forced under a 1400-lb machine base at A . Knowing that the coefficient of static friction at all surfaces is 0.20, (a) determine the force P required to move the wedge, (b) indicate whether the machine base will move.arrow_forwardb.7arrow_forwardThe cylinder shown is of weight W and radius r . Express in terms XV and r the magnitude of the largest couple M that can be applied to the cylinder if it is not to rotate, assuming the coefficient of static friction to be (a) zero at A and 0.30 at B, (b) 0.25 at A and 0.30 at B.Fig. P8.18arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY