Structural Analysis, SI Edition
6th Edition
ISBN: 9780357030981
Author: Aslam Kassimali
Publisher: Cengage Learning US
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 8, Problem 50P
To determine
Draw the influence lines for the force in member AB, BE, EF, BF, and DG.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
The floor of a building, shown in Fig. (a), is subjected to a uniformly distributed load of 3.5 kPa over its surface area.
Determine the loads acting on all the members of the floor system.
AI
Column
Floor beam
B
Slab
C
D
3 at 4 m
= 12 m
Floor beam
E
F
Girder
GT
-9 m.
(a) Framing Plan
Commercial trucks begin to arrive at a seaport entry plaza at 7:50 A.M., at the rate of λ(t) = 6.3 – 0.25t[λ(t) is in veh/min and t is in minutes]. The plaza opens at 8:00 A.M. For the first 10 minutes, one processing booth is open. After the first 10 minutes until the queue clears, two processing booths are open. Each booth processes trucks at a uniform rate of two per minute. What is the average delay per vehicle, the maximum queue length, and the average queue length?
The floor system of a gymnasium consists of a 130-mm-thick concrete slab resting on
four steel beams (A = 9100 mm²) that, in turn, are supported by two steel girders (A =
25600 mm²), as shown in Fig. 2.3. Determine the dead loads acting on beam BF and
girder AD.
2.3 Beam BF
Uniformly distributed load
ㅋㅋ
=28.6 (5) (180) + 77 (100) = 16.04 kN/m
16.04 kN/m
B
80.2 kN
F
80.2 kN.
Chapter 8 Solutions
Structural Analysis, SI Edition
Ch. 8 - Prob. 1PCh. 8 - Prob. 2PCh. 8 - Prob. 3PCh. 8 - Prob. 4PCh. 8 - Prob. 5PCh. 8 - Prob. 6PCh. 8 - Prob. 7PCh. 8 - Prob. 8PCh. 8 - Prob. 9PCh. 8 - Prob. 10P
Ch. 8 - Prob. 11PCh. 8 - Prob. 12PCh. 8 - Prob. 13PCh. 8 - Prob. 14PCh. 8 - Prob. 15PCh. 8 - Prob. 16PCh. 8 - Prob. 17PCh. 8 - Prob. 18PCh. 8 - Prob. 19PCh. 8 - Prob. 20PCh. 8 - Prob. 21PCh. 8 - Prob. 22PCh. 8 - Prob. 23PCh. 8 - Prob. 24PCh. 8 - Prob. 25PCh. 8 - Prob. 26PCh. 8 - Prob. 27PCh. 8 - Prob. 28PCh. 8 - Prob. 29PCh. 8 - Prob. 30PCh. 8 - Prob. 31PCh. 8 - Prob. 32PCh. 8 - Prob. 33PCh. 8 - Prob. 34PCh. 8 - Prob. 35PCh. 8 - Prob. 36PCh. 8 - Prob. 37PCh. 8 - Prob. 38PCh. 8 - Prob. 39PCh. 8 - Prob. 40PCh. 8 - Prob. 41PCh. 8 - Prob. 42PCh. 8 - Prob. 43PCh. 8 - Prob. 44PCh. 8 - Prob. 45PCh. 8 - Prob. 46PCh. 8 - Prob. 47PCh. 8 - Prob. 48PCh. 8 - Prob. 49PCh. 8 - Prob. 50PCh. 8 - Prob. 51PCh. 8 - Prob. 52PCh. 8 - Prob. 53PCh. 8 - Prob. 54PCh. 8 - Prob. 55PCh. 8 - Prob. 56PCh. 8 - Prob. 57PCh. 8 - Prob. 58PCh. 8 - Prob. 59PCh. 8 - Prob. 60PCh. 8 - Prob. 61P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- Trucks begin to arrive at a truck weigh station (with a single scale) at 6:00 A.M. at a deterministic but time-varying rate of λ(t) = 4.3 − 0.22t [λ(t) is in veh/min and t is in minutes]. The departure rate is a constant 2 veh/min (time to weigh a truck is 30 seconds). When will the queue that forms be cleared, what will be the total delay, and what will be the maximum queue length?arrow_forwardhow many custom bricks of size 3 1/4 x 3 3/4arrow_forwardHow many custom bricks of size 3 1/4 x 3 3/4 x 11 7/8 inches are there per square foot of wall area when the mortar joint is 1/4arrow_forward
- Given a circular curve connecting 2 tangents that intersect at an angle of 55°. The PI is at thestation (948+50) and the design speed of the highway is 70 mi/h. Determine:(a) stations of the PC and PT(c) Deflection angles and chord lengths for the first, middle, and last chordsarrow_forwardA simple circular curve exists with a radius of 900 ft connects the tangents of a two-lanehighway that has a posted speed limit of 45 mph. The highway curve is not superelevated,e=0. A structure is proposed on land on the inside of the curve. Assume the road is on a levelgrade. Determine the minimum distance allowable between the proposed structure and thecenterline of the curve such that the current maximum safe speed of the curve would notneed to be reducedarrow_forwardA +4.4% grade intersects with a -3.3% grade at a station (550+30) at an elevation of400 ft. If the design speed is 60 mi/h, determine:(a) the minimum length of the vertical curve using the rate of vertical curvature(b) the stations and elevations of the BVC and EVC(c) the tangent and curve elevations of BVC, full stations, and EVC(d) the station and elevation of the highest pointarrow_forward
- Determine the minimum length of a sag vertical curve if the grades are –3% and +4%. The design speed is 75 mi/h. State all assumptions used. Make sure to consider the following criteria: stopping sight distance, comfort, and general appearancearrow_forwardQuestion 6: Chlorine is widely used to purify municipal water supplies and to treat swimming pool waters. Suppose that the volume of a particular sample of Cl₂ gas is 8.70 L at 895 torr and 24°C. (a) How many grams of Cl₂ are in the sample? ⚫ Atomic mass of CI = 35.453 g/mol • Molar mass of Cl₂ = 2 x 35.453 = 70.906 g/mol Solution: Use the Ideal Gas Law: Step 1: Convert Given Values • Pressure: P = 895 torr → atm PV= = nRT 1 P = 895 × = 1.1789 atm 760 • Temperature: Convert to Kelvin: T24273.15 = 297.15 K • Gas constant: R = 0.0821 L atm/mol. K Volume: V = 8.70 L Step 2: Solve for n . PV n = RT n = (1.1789)(8.70) (0.0821)(297.15) 10.25 n = = 0.420 mol 24.405 Step 3: Calculate Mass of Cl₂ Final Answer: 29.78 g of Cl₂. mass nx M mass= (0.420)(70.906) mass= 29.78 garrow_forwardPlease solve the highlighted question.arrow_forward
- 1. Design a PVC sanitary sewer collection system for the Village of Waffle (Figure P-17-24 B, shown below) by preparing a sewer design table similar to that shown in Example 19-2 and a profile drawing similar to Figure 19-13b B. You only need to show the calculations for the pipes running along Bacon Road and Eggs Road, starting at point F and ending at Point B in the figure below. Your design should comply with the requirements specified in Chapter 30 of the 10 States Standards for Wastewater. Use the following assumptions: 0 о о Average daily flow rate is the same as average daily water demand, 9.2 m³/hr Peaking factor for peak dry weather flow is 6.2 Peak wet weather flow is equal to the peak dry weather flow plus an assumption for infiltration and inflow at 40 L/d-mm-km of pipe DODO on Ro 450 m 28 m D. 150 m Apartments D 400 m D 200 m B 250 m 0 Dogs Road ROOD625 m -120 m Syrup River 120 m 100-Year flood Point Elevation Tank 137.0 m A 130.0 m B 122.0 m C 122.3 m D 122.6 m A D 300 m…arrow_forwardNeed helparrow_forward2. Design a circular clarifier for a flow rate of 34,560 m³/d. Use a design overflow rate of 30 m³/d-m². Assume the clarifier has a center feed and a side water depth of 4.3 m. Use a feedwell detention time of 20 min. Provide the following information to support your design: • Diameter of the clarifier • Diameter and depth of the feedwell . Check the flow velocity across the sludge zone • Calculate the weir loading ratearrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
