The pressure in the flask of manometer should be determined in units of torr and atm when the manometer shows a reading of 20.0 inches. Concept Introduction: The manometer is a devise used measure the pressure of a gas . The pressure of gas is determined by the value of ‘ h ’ shown by the manometer. This ‘h’-value is added or subtracted with atmospheric pressure to determine the pressure of gas. If the flask side mercury level is decreased after the filling of gas, then the ‘h’-value will be added to atmospheric pressure to get the pressure of gas. Atmospheric pressure = 760 mm Hg /torr The pressure equivalent of ‘h’ value is, h = 1 inch = 25 .4 mm Hg Pressure of a substance can be stated in various units. The units of pressure are interconvertible. The relations between the units of pressure are, Since the unit mm Hg and the unit torr is used interchangeably. 1 mm Hg = 1 torr Conversion of 1 torr into atm is, 1 mm Hg = 1 760 atm

Question

Want to see the full answer?

Answer 1

Question

Chapter 8, Problem 40E

Interpretation Introduction

Interpretation:

The pressure in the flask of manometer should be determined in units of torr and atm when the manometer shows a reading of 20.0 inches.

Concept Introduction:

The manometer is a devise used measure the pressure of a gas. The pressure of gas is determined by the value of ‘h’ shown by the manometer. This ‘h’-value is added or subtracted with atmospheric pressure to determine the pressure of gas.

If the flask side mercury level is decreased after the filling of gas, then the ‘h’-value will be added to atmospheric pressure to get the pressure of gas.

Atmospheric pressure = 760 mm Hg /torr

The pressure equivalent of ‘h’ value is,

h = 1 inch = 25.4 mm Hg

Pressure of a substance can be stated in various units. The units of pressure are interconvertible. The relations between the units of pressure are,

Since the unit mm Hg and the unit torr is used interchangeably.

1 mm Hg = 1 torr

Conversion of 1 torr into atm is,

1 mm Hg = 1760 atm

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Students have asked these similar questions

b) Certain cyclic compounds are known to be conformationally similar to carbohydrates, although they are not themselves carbohydrates. One example is Compound C shown below, which could be imagined as adopting four possible conformations. In reality, however, only one of these is particularly stable. Circle the conformation you expect to be the most stable, and provide an explanation to justify your choice. For your explanation to be both convincing and correct, it must contain not only words, but also "cartoon" orbital drawings contrasting the four structures. Compound C Possible conformations (circle one): Дет

Lab Data The distance entered is out of the expected range. Check your calculations and conversion factors. Verify your distance. Will the gas cloud be closer to the cotton ball with HCI or NH3? Did you report your data to the correct number of significant figures? - X Experimental Set-up HCI-NH3 NH3-HCI Longer Tube Time elapsed (min) 5 (exact) 5 (exact) Distance between cotton balls (cm) 24.30 24.40 Distance to cloud (cm) 9.70 14.16 Distance traveled by HCI (cm) 9.70 9.80 Distance traveled by NH3 (cm) 14.60 14.50 Diffusion rate of HCI (cm/hr) 116 118 Diffusion rate of NH3 (cm/hr) 175.2 175.2 How to measure distance and calculate rate

For the titration of a divalent metal ion (M2+) with EDTA, the stoichiometry of the reaction is typically: 1:1 (one mole of EDTA per mole of metal ion) 2:1 (two moles of EDTA per mole of metal ion) 1:2 (one mole of EDTA per two moles of metal ion) None of the above