It is commonly recommended that hot foods be cooled first to room temperature by simply waiting a while before they are put into the refrigerator to save energy. Despite this commonsense recommendation, a person keeps cooking a large pan of stew three times a week and putting the pan into the refrigerator while it is still hot, thinking that the money saved is probably too little. But he says he can be convinced if you can show that the money saved is significant. The average mass of the pan and its contents is 5 kg. The average temperature of the kitchen is 23°C, and the average temperature of the food is 95°C when it is taken off the stove. The refrigerated space is maintained at 3°C, and the average specific heat of the food and the pan can be taken to be 3.9 kJ/kg·°C. If the refrigerator has a coefficient of performance of 1.5 and the cost of electricity is $0.125/kWh, determine how much this person will save a year by waiting for the food to cool to room temperature before putting it into the refrigerator.
FIGURE P6–123
Want to see the full answer?
Check out a sample textbook solutionChapter 6 Solutions
CENGEL'S 9TH EDITION OF THERMODYNAMICS:
- and finally find the volume rate in ft3/dayarrow_forward1. Is a temperature difference necessary to operate a heat engine? State why or why not. 2. Definitions of efficiency vary depending on how energy is being converted. Compare the definitions of efficiency for the human body and heat engines. How does the definition of efficiency in each relate to the type of energy being converted into doing work? 3. Why-other than the fact that the second law of thermodynamics says reversible engines are the most efficient-should heat engines employing reversible processes be more efficient than those employing irreversible processes? Consider that dissipative mechanisms are one cause of irreversibility. 1. (a) What is the efficiency of a cyclical heat engine in which 75.0 kJ of heat transfer occurs to the environment for every 95.0 kJ of heat transfer into the engine? (b) How much work does it produce for 100 k) of heat transfer into the engine? 2. The engine of a large ship does 2.00×10°J of work with an efficiency of 5.00%. (a) How much heat…arrow_forwardDescribe the heat and work are energy transfer mechanisms between a system and its surroundings, and there are many similarities between them?arrow_forward
- (c) A resistant heater jacket 6.5kW is wrapped around a water bath for 240 minutes to raise the water temperature to the desired temperature level. Determine the amount of electric energy used in both kWh and kJ.arrow_forwardb andcarrow_forwardA heat engine has a thermal efficiency of 52%, producing 25 kW of work. Determine the heat transfer rate to the heat engine, in kW. Report your answer to two decimals using rounding.arrow_forward
- A heat engine has a thermal efficiency of 40 percent and it produces 600 kJ of work. What is the heat input to the heat engine, in MJ? Report your answer to one decimal place.arrow_forwardA piston cylinder assembly contains steam. Initially, the specific internal energy (internal energy per unit mass) is equal to 2600 kJ/kg. The steam undergoes a process during which 90 kJ of heat is transferred to the steam. On the other hand, using a specific mechanism installed in the cylinder, 20 kJ of energy are transferred to the steam by work. If 10 kJ of heat is dissipated from the steam to the outside of the cylinder through the wall of the cylinder, Determine the work done by the steam on the piston. The specific internal energy at the final state is equal to 2500 kJ/kg. The mass of the steam is 4.4 kg. Select one: a. 1211 kJ b. 540 kJ c. 780 kJ d. 328 kJarrow_forwardThe thermal effiency of a general heat engine is 35 percent, and it produces 60 hp. At what rate is heat transferred to this engine, in kJ/s?arrow_forward
- Define the Energy can cross the boundaries of a closed system in the form of heat and work?arrow_forwardCalculate the total potential energy, in Btu, of an object that is 20 ft below a datum level at a location where g = 31.7 ft/s2 and which has a mass of 100 lbm.arrow_forwardIf the energy crossing the boundary of a closed system is not heat, it must be work?arrow_forward
- Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning