Concept explainers
Find the slope

Answer to Problem 34P
The slope
The deflection
The slope
The slope
The deflection
Explanation of Solution
Given information:
The Young’s modulus (E) is 30,000 ksi.
The moment of inertia of the section AB is (I) is
The moment of inertia of the section BD is (I) is
Calculation:
Consider Young’s modulus (E) of the beam is constant.
To draw a
Show the free body diagram of the given beam as in Figure (1).
Refer Figure (1),
Consider upward is positive and downward is negative.
Consider clockwise is negative and counterclowise is positive.
Refer Figure (1),
Consider reaction at A and C as
Take moment about point B.
Determine the reaction at C;
Determine the reaction at support A;
Determine the moment at A:
Show the reactions of the given beam as in Figure (2).
Determine the bending moment at B;
Determine the bending moment at C;
Determine the bending moment at D;
Determine the positive bending moment at A;
Show the reaction and point load of the beam as in Figure (3).
Determine the value of
Substitute
Show the
Show the elastic curve as in Figure (5).
The slope at point B can be calculated by evaluating the change in slope between A and B.
Express the change in slope using the first moment-area theorem as follows:
Here, b is the width and h is the height of the respective triangle and rectangle.
Substitute 16 ft for
Determine the slope B (left) using the relation;
Substitute 30,000 ksi for E and
Hence, the slope at B (left) is
Determine the deflection at B using the relation;
Substitute
Determine the deflection at B (left) using the relation;
Substitute 30,000 ksi for E and
Hence, the deflection at B (left) is
Determine the deflection between B and C using the relation;
Here, b is the width and h is the height of the triangle.
Substitute 8 ft for b and
Express the relationship between the deflection and slope of span BC as follows:
Here,
Substitute
Determine the slope between B and C using the relation;
Substitute 8 ft for b and
Determine the slope at B (right) using the relation;
Substitute
Substitute 30,000 ksi for E and
Hence, the slope at B (right) is
Determine the slope between C and D using the relation;
Here, b is the width and h is the height of the triangle.
Substitute 8 ft for b and
Determine the slope at D using the relation;
Substitute
Substitute 30,000 ksi for E and
Hence, the slope at point D is
Determine the deflection between C and D using the relation;
Substitute
Determine the deflection at point D using the relation;
Substitute 8 ft for
Substitute 30,000 ksi for E and
Hence, the deflection at point D is
Want to see more full solutions like this?
Chapter 6 Solutions
Structural Analysis, 5th Edition
- please solve and neglect the distance between the two angles for simplecalculationsarrow_forwardDetermine the required solids retention time (SRT) of a completely mixed activated sludge aeration tank for a conventional activated sludge system treating a design flow rate of 34,560 m³/d, where the effluent standards are 30.0 mg/L for BODs and 30.0 mg/L for total suspended solids (TSS). Assume that the BOD5 of the effluent TSS is 70% of the TSS concentration. Assume the BODs concentration leaving the primary clarifier is 128 mg/L that the MLVSS concentration (X₂) is 2,500 mg/L. Assume the following values for the growth constants: Ks 100 mg/L BODS ⚫ Hm - 2.5 d 1 kd = 0.050 d 1 Y = 0.50 mg VSS/mg BODs removed Express your answer in days and round to the nearest 0.1.arrow_forwardFor the gravity concrete dam shown in the figure, the following data are available: Unit weight of concrete (7)-2.4 ton/m Neglect Wave pressure, silt pressure, ice force and earth quake force) -0.65, (7)-1 ton/m' Solve on paper and sketch Find factor of safety against sliding and overturning (F.Sa & F.S), If heel and toe stresses (Pain & P) are 57.17ton/m2 and 84.53 ton/m² respectively. Solve in table on paper w.s.l 83m 10m 8m 80marrow_forward
- 1. Find moments of inertia around horizontal and vertical centroid axes for given 6 cross sections. 30cm 4) "T 0cm 1116 5) 20cm 5cm 6)arrow_forward1. Find moments of inertia around horizontal and vertical centroid axes for given 6 cross sections. 1) 30cm 5cm 10cm 20cm 2) 3)arrow_forwardAn anchored sheet-pile bulkhead is shown in the figure below. Let L₁ = 2 m. L₂ =6 m. l₁ = 1 m = 17 kN/m². sat -18.86 kN/m², '=32°, and c=27 kN/m². Use the free earth support method. Anchor Sand = 0 Water table L Sand Ysat c' = 0 Clay = 0 1. Determine the theoretical depth of embedment, D. (Enter your answer to three significant figures.) D= m 2. Calculate the anchor force per unit length of the sheet-pile wall. (Enter your answer to three significant figures.) F= kN/marrow_forward
- Calculate the dry mass of activated sludge (✗a) produced in wastewater treatment system where the flow rate is 7,500 m³/day, the BOD concentration in the primary effluent (i.e., the BOD concentration in the wastewater going to the aeration basin) is 75 mg/L, the soluble BOD concentration in the liquid effluent of the secondary clarifier is 10 mg/L, and the system is operating with an SRT of 3 days. Assume true yield is 0.5 g VSS per g BOD and the decay rate (i.e., bч or kd) is equal to 0.1 days 1. Assume the system does not achieve nitrification and that the mass of cell debris, nonbiodegradable VSS, and influent inert TSS is negigible. Express your answer in kg/day and round to the nearest 0.1.arrow_forwardIn a school, there are three clubs: Drama Club, Music Club, and debating Club. Some students are members of multiple clubs, while others are only members of one club. a. How would you represent this scenario using set notation and Venn Diagram?arrow_forwardDetermine the required volume of a completely mixed activated sludge aeration tank for a conventional activated sludge system treating a design flow rate of 34,560 m³/d, where the effluent standards are 30.0 mg/L for BOD5 and 30.0 mg/L for total suspended solids (TSS). Assume that the BOD5 of the effluent TSS is 70% of the TSS concentration. Assume the BOD5 concentration leaving the primary clarifier is 128 mg/L that the MLVSS concentration (Xa) is 2,500 mg/L. Assume the following values for the growth constants: • K = 100 mg/L BOD5 • μm = 2.5 d−1 • kd = 0.050 d 1 Y = 0.50 mg VSS/mg BOD5 removed Express your answer in m³ and round to the nearest integer.arrow_forward
- Determine the daily volume of methane and total gas produced in an anaerobic digester if the biosolids flow rate is 200 m³/d and the COD concentration going into the reactor is 5,000 g/m³. Assume yield is 0.05 g VSS/g COD, that there is 90% COD removal, and that methane is 50% of the total gas volume. Assume that actual gas production at the operating temperature is 0.4 L of CH4 per g of COD. Express your answer in m³/d and round to the nearest integer.arrow_forwardConsidering the following stoichiometry shown below, calculate the theoretical true yield of bacteria that use the organic molecule butyrate (C4 H7O2¯) as their source of energy. Express your answer with the units of grams of C5 H7O2 N per gram of O2 and round to the nearest 0.01. Stoichiometric relationship for the microbial oxidation of butyrate with O₂ as terminal electron acceptor 2C4H;O, +502+NHẠ* → C5 H7O2 N + 5H2O+ HCO3 + CO2 Stoichiometric relationship for the complete oxidation of butyrate C4H7O2 +502 + H+ →4CO2+4H₂Oarrow_forwardRefer to the figure below. Given: L₁ = 4m, L2 = 8 m, l₁ = l2 = 2 m, y = 16 kN/m³, Ysat = 18.5 kN/m³, and ' = 26°. Use the charts presented below the answer fields. Sand c' = 0 Anchor L₁ Water table Sand Ysat c' 0 $' Sand c' = 0 1. Determine the theoretical depth of penetration. (Enter your answer to two significant figures.) D= m 2. Determine the anchor force per unit length. (Enter your answer to two significant figures.) F= kN/m 3. Determine the maximum moment in the sheet pile. (Enter your answer to two significant figures.) CDL₁ Mmax = 0.5 kN-m/m 0.4- -24= &' 26° 0.3 -28° 30° 32° 0.2 34° 36° 38° 0.1 0.0 0.1 0.2 0.3 0.4 0.5 1.18 1.16 1.14 1.12 1.10 1.08 1.06 1.04 4₁/(L₁+ L₂2) L₁ 4₁+12 0.3 0.2 = 0.4arrow_forward
