Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781305176423
Author: ERJAVEC
Publisher: Cengage
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 43, Problem 7RQ
Ifa transmission does not have a dipstick, how do you check the level of the fluid?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
4.
(a) State the conditions that must be met to ensure dynamic balance is achieved for long rotors.
(b) A rotor carries three out-of-balance discs in planes A, B and C as shown in Figure 4. The out-of-
balance mass x radius products of the rotor discs are tabulated in Table 4.
The shaft is to be dynamically balanced by adding balancing masses in planes P and Q, spaced along
the shaft at a distance da = 800 mm.
Determine the magnitude mara and angular position of the balancing mass x radius product that
must be added to plane Q.
MBB
Ов
θε
mdc
Мага
End View on Plane P
P
MBB
MATA
dA
dB
dc
do
Figure 4
moc
Table 4
MATA = 0.6 kg mm
6A = 0°
d₁ = 200 mm
mers = 0.2 kg mm
6g = 45°
dB = 400 mm
mcrc = 0.4 kg mm
Bc=240°
dc = 600 mm
Ans. (b) = 110.5°, moro = 0.2 kg mm
Need help in adding demensioning am am so confused
Complete the following activity. Save as .pdf and upload to the assignment to the dropbox.
口
Use the general dimensioning symbols to correctly specify the following requirements on the
drawing above.
Chapter 43 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 43 - What is the most probable cause of a low fluid...Ch. 43 - What does milky colored ATF indicate?Ch. 43 - What do varnish or gum deposits on the dipstick...Ch. 43 - Typically during a pressure test, the pressure...Ch. 43 - What should you do if a valve does not move freely...Ch. 43 - Which of the following is the most likely cause...Ch. 43 - Ifa transmission does not have a dipstick, how do...Ch. 43 - What is checked during a stall test?Ch. 43 - When should the ATF level be checked on most...Ch. 43 - List five reasons for replacing a torque...
Ch. 43 - Pressure readings reveal possible problems in...Ch. 43 - Which of the following is a probable cause for a...Ch. 43 - When rebuilding an automatic transmission, which...Ch. 43 - Explain why oil circuit diagrams are invaluable...Ch. 43 - Explain how a plugged fluid cooler can cause a...Ch. 43 - Technician A says that a prerequisite to accurate...Ch. 43 - While discussing proper band adjustment...Ch. 43 - Technician A says that if the shift for all...Ch. 43 - Technician A says that the only positive way to...Ch. 43 - Technician A says that delayed shifting can be...Ch. 43 - While checking the condition of a cars ATF:...Ch. 43 - While discussing the results of an oil pressure...Ch. 43 - While discussing a pressure test: Technician A...Ch. 43 - While checking the engine and transmission mounts...Ch. 43 - While discussing the cause of aerated fluid in a...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- please solve and show workarrow_forwardWater is boiling in a 25 cm diameter aluminum pan (k=237 W/mK) at 95 degrees C. Heat is transferred steadily to the boiling water in the pan through its .5 cm thick flat bottom at a rate of 800 W. if the inner surface temp of the bottom of the pan is 108 degrees C determine the boiling heat transfer coefficent on the inner surface of the pan and the outer surface temp of the bottom of the pan.arrow_forwardplease solve and show workarrow_forward
- please solve and show workarrow_forwardA thin plastic membrane separates hydrogen from air. The molar concentrations of hydrogen in the membrane at the innner and outer surfaces are determined to be 0.045 and 0.002 kmol/m^3 respectiveley. The binary diffusion coefficent of hydrogen in plastic at the operation temp is 5.3*10^-10 m^2/s. Determine the mass flow rate of hydrogen by diffusion through the membrane under steady conditions if the thickeness of the membrane is 2mm and 0.5 mm.arrow_forwardCalculate the vertical cross section moment of inertia for Orientations 1 and 2. State which number is the higher moment of inertia using equation 1. Given: b1=1 in, h1=1.5 in, b2=1.5 in, h2=1 in, t=0.0625 in. Then calculate the maximum deflection for a point load of 8 lb on the free end of the beam using equation 2. Given: E=10.1*10^6 psi. 1. ((bh^3)/12) - (((b-2t)(h-2t)^3))/12) 2. S = (PL^3)/(3EI)arrow_forward
- 1-69E The pressure in a natural gas pipeline is measured by the manometer shown in Fig. P1-69E with one of the arms open to the atmosphere where the local atmospheric pressure is 14.2 psia. Determine the absolute pressure in the pipeline. Natural Gas 10 in 6 in FIGURE P1-69E Mercury SG= 13.6 Air 2 in + 25 in Waterarrow_forwardB 150 mm 120 mm PROBLEM 15.193 The L-shaped arm BCD rotates about the z axis with a constant angular velocity @₁ of 5 rad/s. Knowing that the 150-mm- radius disk rotates about BC with a constant angular velocity @2 of 4 rad/s, determine (a) the velocity of Point A, (b) the acceleration of Point A. Answers: V₁ =-(0.600 m/s)i + (0.750 m/s)j - (0.600 m/s)k a=-(6.15 m/s²)i- (3.00 m/s²)jarrow_forward3 Answer: 002 PROBLEM 15.188 The rotor of an electric motor rotates at the constant rate @₁ = 1800 rpm. Determine the angular acceleration of the rotor as the motor is rotated about the y axis with a constant angular velocity 2 x of 6 rpm counterclockwise when viewed from the positive y axis. α = (118.4 rad/s²)iarrow_forward
- 12 in.. 10 in. PROBLEM 15.187 At the instant considered the radar antenna shown rotates about the origin of coordinates with an angular velocity @ = ai + @j+wk Knowing that (VA) = 15 in./s, (VB), 9 in./s, and (VB), = 18 in./s, determine (a) the angular velocity of the antenna, (b) the velocity of point A. B 10 in. Answers: = (0.600 rad/s)i - (2.00 rad/s) j + (0.750 rad/s)k V₁ = (20.0 in./s)i + (15.00 in./s) j + (24.0 in./s)karrow_forward3. An engine has three cylinders spaced at 120° to each other. The crank torque diagram can be simplified to a triangle having the following values: Angle 0° Torque (Nm) 0 (a) What is the mean torque? 60° 4500 180° 180° to 360° 0 0 (b) What moment of inertia of flywheel is required to keep the speed to within 180 ± 3 rpm? (c) If one cylinder of the engine is made inoperative and it is assumed that the torque for this cylinder is zero for all crank angles, determine the fluctuation in speed at 180rpm for the same flywheel. (a) 3375 Nm (b) 50kgm (c) ±21 rpmarrow_forwardProb 5. Determine the largest load P that can be applied to the frame without causing either the average normal stress or the average shear stress at section a-a to exceed o-150 MPa and 1-60 MPa, respectively. Member CB has a square cross section of 25 mm on each side. 2 m FAC 1.5 m Facarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Fluid Mechanics - Viscosity and Shear Strain Rate in 9 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=_0aaRDAdPTY;License: Standard youtube license