Calculate the vertical cross section moment of inertia for Orientations 1 and 2. State which number is the higher moment of inertia using equation 1. Given: b1=1 in, h1=1.5 in, b2=1.5 in, h2=1 in, t=0.0625 in. Then calculate the maximum deflection for a point load of 8 lb on the free end of the beam using equation 2. Given: E=10.1*10^6 psi. 1. ((bh^3)/12) - (((b-2t)(h-2t)^3))/12) 2. S = (PL^3)/(3EI)

Calculate the vertical cross section moment of inertia for Orientations 1 and 2. State which number is the higher moment of inertia using equation 1. Given: b1=1 in, h1=1.5 in, b2=1.5 in, h2=1 in, t=0.0625 in. Then calculate the maximum deflection for a point load of 8 lb on the free end of the beam using equation 2. Given: E=10.1*10^6 psi. 1. ((bh^3)/12) - (((b-2t)(h-2t)^3))/12) 2. S = (PL^3)/(3EI)

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter9: Deflections Of Beams

Section: Chapter Questions

Problem 9.7.1P: The cantilever beam ACB shown in the figure has moments of inertia /, and I{in parts AC and CB,...

See similar textbooks

Similar questions

3. Determine the displacement and slope (i.e. 0) at the load point for the stepped beam shown in the following figure. Also determine the reaction forces and moments. Each element has E = 200 GPa. The area moment of inertia are given as I₁ = 1.25 × 105 mm4, and 2 = 4 x 104 mm. Clearly show the elemental stiffness matrices (k) for each element, assembly of k matrices to get global stiffness matrix (K) and application of boundary conditions. Then solve the reduced K matrix to get displacements and reactions 3000 N 150 mm 75 mm 125 mm
A thin beam with a solid rectangular cross-section is loaded as shown in Figure Q7 below. L/3 L/3 L/3 Figure Q7 Consider the following statoments and select which combination correctly describes the bending moment diagram for this beam, along its longth using the sign conventions provided in lectures. i lt is symmetrical. ii It has a value of zero at the mid-point. i. It has a negative value for the entire length of the beam. iv. It is described by a quadratic (2nd order) function. O ali and i. are both correct. Ob.li. and iv. are both correct. Oci. and i. are both correct. Od.i. and iv. are both correct. Oe. li. and iv. are both correct. O. None of the provided answers are correct. OBi and i. are both correct.
show full calculation with free body digrams and use Macaulay's notation.
Parvinbhai
A beam with a uniform load has a sliding support at one end and spring support at the other. The spring has a stiffness k = 48EI / L3. Derive the equation of the deflection curve by starting with the third-order differential equation (the shear-force equation). Also, determine the angle of rotation θB at support B.
beam, simply supported at its ends, carries a load which increases uniformly from 15kN/m at the left-hand end to 100 kN/m at the right-hand end. If the beam is 5m long, find the equation for the rate of loading and, using this, to determine the deflection of the beam at mid-span if E= 200GN/m² and I=600*10 m².
Find the torsion constant of the following beam cross section.
Solve using DIM. Previous answer here was wrong so please correct it.
MA MB= Mc= MD= Required information For the beam shown, find the reactions at the supports and plot the shear-force and bending-moment diagrams. V=50 lbf/in and V2 = 7 in. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Hinge = 1400 lbf/ A BI AC R₂ R₁ 4 in 4 in 2 in V1 Determine the values of the moments at points A, B, C, and D. lbf.in lbf.in lbf.in Ibf.in V2 D R₂
The beam shown below is supported by rollers at A and B, and by a pin at C. If EI is constant over the length of the beam, find the reaction forces at A, B, and C. 15 kip AT 6 ft B_ 6 ft 12 ft 3 kip/ft C
Determine the reactions at the supports. The moment of inertia for each segment is shown in the figure. Assume the support at B is a roller. Take E=29(10^3)ksi
Cantilever beam is loaded by three concentrated forces. F, 1 Given: 11= 1Ocm; 1 2 = 25cm; 1 3 = 19cm; F1 = -0.2kN; F , = -0.6kN; F 3 = -1.6kN . Find: algebraical value of reactive moment (in N m) applied at fixed point (considering counterclockwise direction as positive and clockwise as negative). Answer: