Explanation Given information: The applied load P is 15 kN . The height ( h ) of the cross-section is 60 mm . The cross-section of the component is a trapezoid. The inner radius of curved component is r 1 = 40 mm . Calculation: Show the cross section of the machine component as shown in Figure 1. Refer Figure 1. Consider the area of the triangle 1 and 2 are denoted by A 1 and A 2 . Calculate the area of the triangle 1 and 2 as follows: A 1 = 1 2 b 1 h 1 = 1 2 × 35 × 60 = 1050 mm 2 A 2 = 1 2 b 2 h 2 = 1 2 × 25 × 60 = 750 mm 2 Calculate the mean radius of triangle 1 as follows: Substitute 40 mm for r 1 and 60 mm for h . r ¯ 1 = r 1 + 1 3 h = 40 + 1 3 × 60 = 60 mm Calculate the mean radius of triangle 2 as follows: Substitute 40 mm for r 1 and 60 mm for h . r ¯ 2 = r 1 + 2 3 h = 40 + 2 3 × 60 = 80 mm Calculate the mean radius ( r ¯ ) of the cross-section using the relation: r ¯ = A 1 r ¯ 1 + A 2 r ¯ 2 A 1 + A 2 (1) Substitute 750 mm 2 for A 2 , 1050 mm 2 for A 1 , 60 mm for r ¯ 1 , and 80 mm for r ¯ 2 in Equation (1). r ¯ = 1050 × 60 + 750 × 80 1050 + 750 = 123 , 000 1 , 800 = 68.333 mm The width of the triangle 1 and 2 are b 1 = 35 mm and b 2 = 25 mm Show the formula for the radius ( R ) of the neutral surface for the trapezoidal cross-section as follows: R = 1 2 h 2 ( b 1 + b 2 ) ( b 1 r 2 − b 2 r 1 ) ln r 2 r 1 − h ( b 1 − b 2 ) (2) Substitute 35 mm for b 1 , 25 mm for b 2 , 40 mm for r 1 , 100 mm for r 2 , and 60 mm for h in Equation (2)

7th Edition

ISBN: 8220100257063

Author: BEER

Publisher: YUZU

See similar textbooks

Videos

Question

Chapter 4.10, Problem 186P

To determine

Find the largest tensile stress in section a-a.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 4.10, Problem 185P

Chapter 4.10, Problem 187P

Students have asked these similar questions

M= 500 Nm PROBLEM 4.2 Knowing that the couple shown acts in the vertical plane, determine the stress at (a) point A, and (b) point B. [Ans. (a) -116.4 MPa (b) -87.3 MPa] 30 mm 40 mm Fig. P4.2 E231 hp

4.99 plz

The member having a rectangular cross-section, Fig. a, is designed to resist a moment of 40 N # m. In order to increase its strength and rigidity, it is proposed that two small ribs be added at its bottom, Fig. b. Determine the maximum normal stress in the member for both cases.

Chapter 4 Solutions

EBK MECHANICS OF MATERIALS

Ch. 4.3 - 4.1 and 4.2 Knowing that the couple shown acts in...Ch. 4.3 - 4.1 and 4.2 Knowing that the couple shown acts in...Ch. 4.3 - Using an allowable stress of 155 MPa, determine...Ch. 4.3 - Solve Prob. 4.3, assuming that the wide-flange...Ch. 4.3 - Using an allowable stress of 16 ksi, determine the...Ch. 4.3 - Knowing that the couple shown acts in a vertical...Ch. 4.3 - 4.7 and 4.8 Two W4 13 rolled sections are welded...Ch. 4.3 - 4.7 and 4.8 Two W4 13 rolled sections are welded...Ch. 4.3 - 4.9 through 4.11 Two vertical forces are applied...Ch. 4.3 - 4.9 through 4.11 Two vertical forces are applied...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Find the largest tensile stress in section a - a .

Solution Summary: The author shows the largest tensile stress in section a-a, and the cross-section of the machine component, as shown in Figure 1.

Videos

Find the largest tensile stress in section a-a.

Want to see the full answer?

Chapter 4 Solutions