![Heating Ventilating and Air Conditioning: Analysis and Design](https://www.bartleby.com/isbn_cover_images/9780471470151/9780471470151_largeCoverImage.gif)
What do you think is the best thermostat setting (air dry bulb temperature) in a shop where the workmen are standing, walking, lifting, and performing various machining tasks? Assume that a globe temperature measurement reads 72 F (22 C), the relative humidity will be in the 45 percent range, and air motion will likely be around 30 ft/mm (0.15 m/s). The men are dressed in typical summer garments
![Check Mark](/static/check-mark.png)
Want to see the full answer?
Check out a sample textbook solution![Blurred answer](/static/blurred-answer.jpg)
Chapter 4 Solutions
Heating Ventilating and Air Conditioning: Analysis and Design
Additional Engineering Textbook Solutions
Manufacturing Engineering & Technology
Engineering Mechanics: Statics
Fundamentals of Heat and Mass Transfer
Fundamentals Of Thermodynamics
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
Engineering Mechanics: Dynamics (14th Edition)
- QUESTION 24 300 people are watching a movie at a movie theater which is maintained at 75°F DB. The movie starts at 12:30 pm and ends at 2:30 pm. What is the total cooling load from people ? 20,000 BTU/hr O 31,500 BTU/hr O 67,500 BTU/hr 99,000 BTU/hrarrow_forward2. what do we need to ensure when it comes to sound and noise in the Hangar? 3. why do we need to control the temperature and humidity in the hangar? how does it affect our mechanics?arrow_forwardQuestion The condition of air in a restaurant kitchen is defined based on the Tab of 23°C and relative humidity (RH) of 60%. Please respond to the following questions: a) Find the psychrometric properties of air at this point (TWB, TDP, W, v, h) and show them on the chart. (Attach a screenshot of your chart [can be done by hand] in the same file as your response) b) The surface temperature of the kitchen window in winter is 12°C. Determine if moisture will condense on the window surface. Why?arrow_forward
- please answer do not image formatarrow_forwardFor Questions 6 and 7 The dry-bulb temperature and wet-bulb temperature of a sample of air are 23°C and 18°C, respectively. The pressure of the air is 97 kPa. If the air was adiabatically saturated: Question 6 Calculate the humidity ratio in kg of vapor per kg of dry air. Round your answer to 5 decimal places. Add your answer Question 7 What is its degree of saturation in %? Round your answer to 0 decimal places. Add your answerarrow_forwardQ2) Air is supplied to an automobile cabin from the outside, where the temperature is 20F and the relative humidity is 70%. It is desired to keep the cabin at 70F and Ø = 60%. Hoe many pounds of water must be supplied to each pound of air entering the car cabin if these conditions are to be met? The barometric pressure is 29.5 in.Hg. %3D Ans. (0.00797 lbs/Ibdry air)arrow_forward
- ASHRAE standard 62.2 states that the minimum acceptable rate of airflow into and out of a room is 15cfm (cubic feet per minute). If air is supplied at 68°F with a relative humidity of 45%, how many gallons of water (minimum) must be added to a portable room humidifier before you go to sleep if you would like to maintain the room at 65% humidity for 7 hours?arrow_forwardIf the dry-bulb temperature of the air surrounding a typical cooling is 90 degrees Fahrenheit and the relative humidity of the air is 50%, the cooling tower should be able to cool the water in the tower to a temperature of: A. 82 degree Fahrenheit B. 75 degree Fahrenheit C. 89 degree Fahrenheit D. 95 degree Fahrenheitarrow_forwardUse the concept of evaporative cooling to explain how air’s relative humidity is measured using a sling psychrometerarrow_forward
- Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. An air-conditioning system operates at a total pressure of 1 atm and consists of a heating section and a humidifier that supplies wet steam (saturated water vapor) at 100°C. Air enters the heating section at 10°C and 70 percent relative humidity at a rate of 32 m /min, and it leaves the humidifying section at 20°C and 60 percent relative humidity. Use data from the tables. Sat. vapor 100°C Heating coils Humidifier 10°C Air 20°C 70% 60% ymYmin P=1 atm Determine the temperature and relative humidity of air when leaves the heating section. The temperature is °C. The relative humidity is %.arrow_forward1. Using a sling psychrometer, you measure the air temperature to be 6°C and the wet-bulb temperature to be 2°C. What is the dew point temperature? (number to one decimal place only). 2. Using a sling psychrometer, you measure the air temperature to be 0°C and the wet-bulb temperature to be -1°C. What is the dew point temperature? 3. Using a sling psychrometer, you measure the air temperature to be 0°C and the wet-bulb temperature to be -1°C. What is the relative humidity?arrow_forwardUsing a psychometric diagram, describe the heating and humidification process from the following data. Initially the air was at dry bulb temperature (DBT) 35 ° C and RH 35%. air preheated to DBT 85 ° C. The heated air is then flowed through a humidifier to increase the RH to 25%. for this process, count, a. change in absolute humidity of air from initial to final conditions = ..... (kg water / kg air) b. change in air enthalpy from initial to final conditions = ..... (kj / kg air)arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
![Text book image](https://www.bartleby.com/isbn_cover_images/9780190698614/9780190698614_smallCoverImage.gif)
![Text book image](https://www.bartleby.com/isbn_cover_images/9780134319650/9780134319650_smallCoverImage.gif)
![Text book image](https://www.bartleby.com/isbn_cover_images/9781259822674/9781259822674_smallCoverImage.gif)
![Text book image](https://www.bartleby.com/isbn_cover_images/9781118170519/9781118170519_smallCoverImage.gif)
![Text book image](https://www.bartleby.com/isbn_cover_images/9781337093347/9781337093347_smallCoverImage.gif)
![Text book image](https://www.bartleby.com/isbn_cover_images/9781118807330/9781118807330_smallCoverImage.gif)