Electric Motor Control
10th Edition
ISBN: 9781133702818
Author: Herman
Publisher: CENGAGE L
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 39, Problem 10SQ
The speed of a synchronous motor is fixed by the
- a. rotor winding.
- b. amortisseur winding.
- c. supply voltage.
- d. frequency of power supply and number of poles.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Consider the circuit shown in the figure. The current through the 6.00Ω resistor is 4.00 A, in the direction shown. Determine the value of(a) the overall voltage in the voltage source and (b) the current andvoltage for each resistor.
Design a circuit to interface 8KB RAM to the 8085 microprocessor starting at address from 2000H.
HANDWRITTEN SOLUTION NOT USE CHATGPT
Use the mesh - current method to find io in the circuit in ( Figure 1 ) . Suppose that v = 100V . Express your answer to three significant figures and include the appropriate units.
Chapter 39 Solutions
Electric Motor Control
Ch. 39 - Prob. 1SQCh. 39 - What is the effect of the starting winding of the...Ch. 39 - What are typical applications of synchronous...Ch. 39 - Prob. 4SQCh. 39 - A loaded synchronous motor cannot operate...Ch. 39 - Why must a discharge resistor be connected in the...Ch. 39 - Depending on their power factor ratings, what is...Ch. 39 - At what power factor do incandescent lights...Ch. 39 - Prob. 9SQCh. 39 - The speed of a synchronous motor is fixed by the...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The memory map of a 8 kB memory chip begins at the location E000H. The last location of the memory address.arrow_forwardThe question was to obtain the Fourier series for the periodic function f(x)= -2 when -πarrow_forwardConsider the homogeneous RLC circuit (no voltage source) shown in the diagram below. Before the switch is closed, the capacitor has an initial charge go and the circuit has an initial current go. R w i(t) q(t) C н After the switches closes, current flows through the circuit and the capacitor begins to discharge. The equation that describes the total voltage in the loop comes from Kirchoff's voltage law: di(t) L + Ri(t) + (t) = 0, dt (1) where i(t) and q(t) are the current and capacitor charge as a function of time, L is the inductance, R is the resistance, and C is the capacitance. Using the fact that the current equals the rate of change of the capacitor charge, and dividing by L, we can write the following homogeneous (no input source) differential equation for the charge on the capacitor: ä(t)+2ag(t)+wg(t) = 0, (2) where R a 2L and w₁ = C LC The solution to this second order linear differential equation can be written as: where 81= q(t) = Ae³¹- Bel 82 = (3) (4) (5)arrow_forward
- 2. 1. A. Simplify the models in the following block diagrams to open loop models (Y/R = G). U(s) o G₁ ROS G₂ 1-GG G4 X₁ Σ az 51- 515 G6 G₂ 5 G₂ M b₁ b₂ Σ o Y(s) X₁ byarrow_forwardNeed handwritten solution do not use chatgpt or AIarrow_forwardB. Design a 2nd order Band Stop Filter (BSF) with overall gain=10, centre frequency-12kHz, and bandwidth=4KHz. (8 Marks)arrow_forward
- Design a fifth (5th) order HPF with 8 KHz cutoff frequency, and overall gain Av=35.57dB. Calculate the roll-off rate and draw its frequency response.arrow_forwardThe reverse recovery charge and the peak reverse current are QH-500 uC and I-250A respectively. Assume that the softness factor is SF=0.5, estimate (a) The reverse recovery time of the diode trr (b) The rate of fall of the diode current di/dtarrow_forwardQ2: A 208V, Y-connected synchronous motor is drawing 40A at unity power factor from a 208V power system. The field current flowing under these conditions is 2.7A. Its synchronous reactance is 0.82 and its armature resistance is 0.2 2. Assume a linear open-circuit characteristic. 1- Find EA and the torque angle. 2- How much field current would be required to make the motor operate at 0.8 PF lagging. 3- How much field current would be required to make the motor operate at 0.8 PF leading. 4- How much field current would be required to make the motor operate at unity PF.arrow_forward
- 6) For each case find the answer: 2 (a) If q (t) = 2+ + 6 + + 3 Coulombs Find i(t) at t = 4 seconds (b) If i(t) = 4 Amperes If Find q (t) for 25 = ≤6 seconds (c) If w(t) = 5t³ Joules Find p(t) at t = 3 seconds (d) If p(t 2t+3+4 Watts Find w(t) for 1st≤5 secondsarrow_forwardAs we will learn in Chapter 8, to maximize the transfer of power from an input circuit to a load ZL, it is necessary to choose ZL such that it is equal to the complex conjugate of the impedance of the input circuit. For the circuit in Fig. P7.50, such a condition translates into requiring ZL = Zth*. Determine ZL such that it satisfies this condition.arrow_forward7.44 In the circuit of Fig. P7.44, what should the value of L be 104 rad/s so that i(t) is in-phase with u,(t)? at i(t) 50 Ω www Ds(f) z- 25 Ω 4μF L b Figure P7.44 Circuit for Problem 7.44.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Electricity for Refrigeration, Heating, and Air C...Mechanical EngineeringISBN:9781337399128Author:Russell E. SmithPublisher:Cengage Learning
Electricity for Refrigeration, Heating, and Air C...
Mechanical Engineering
ISBN:9781337399128
Author:Russell E. Smith
Publisher:Cengage Learning
Working of Synchronous Motor; Author: Lesics;https://www.youtube.com/watch?v=Vk2jDXxZIhs;License: Standard Youtube License