Electric Motor Control
10th Edition
ISBN: 9781133702818
Author: Herman
Publisher: CENGAGE L
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 39, Problem 6SQ
Why must a discharge resistor be connected in the field circuit for starting?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Q choose the correct answer:
1-Brushless excitation system consisting of....
a- Stator field winding and power diodes
b-stator and rotor field winding and capacitor
c- stator and rotor field winding and capacitor
d- Everything mentioned in the options
2- Voltage generated per phase in an alternator is
proportional to
a- Flux per pole
b- Number of turns in armature
c-Winding factors
d- Everything mentioned in the options
e- Frequency of waveform
3- If input mech. Power of SG constant, the functionality of
AVR is
a- Control flux of rotor
b-Control terminal voltage
c- Control flux and terminal voltage
d-Control Load angle
Q2: b- Explain how does the three- phase induction motor work? *
Identify the DC Generator used for
Arc Welding purpose. With a neat
sketch explain its working. List it's
advantages and disadvantages.
Chapter 39 Solutions
Electric Motor Control
Ch. 39 - Prob. 1SQCh. 39 - What is the effect of the starting winding of the...Ch. 39 - What are typical applications of synchronous...Ch. 39 - Prob. 4SQCh. 39 - A loaded synchronous motor cannot operate...Ch. 39 - Why must a discharge resistor be connected in the...Ch. 39 - Depending on their power factor ratings, what is...Ch. 39 - At what power factor do incandescent lights...Ch. 39 - Prob. 9SQCh. 39 - The speed of a synchronous motor is fixed by the...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Answer by step by step procedure Make sure to illustrate the problem Box the final answerarrow_forwardIdentify the DC Generator used for Arc Welding purposes. with a neat sketch explain its working. List it’s advantages and disadvantages.arrow_forwardSolve the question in step by step procedure. Make sure to illustrate if needed Box the final answerarrow_forward
- Subject : electrical machine Please write handwritten Answerarrow_forwardAnswer Letter C only.arrow_forwardAn 8-pole, 600 rpm dc shunt with 778 wave connected armature conductors of 12.5 ohms resistance at a terminal voltage of 250 volts. The armature resistance is 0.25 ohm the shunt field resistance is 250 ohms. Determine the flux per pole? (Our subject is Electrical Machines 1 ) (I need a clear answer and solution. Thank you so much)arrow_forward
- Question 11 Design a Duplex layer simplex lap winding DC machine armature winding by providing a complete wiring diagram with the following Number of Poles: 2 Number of Slots; 8 Thank you and Godbless ASAP pleaseearrow_forwardWhy is more than one coil used on a generator armature? a) to help keep the brush voltage as low as possible b) to increase the difference between the brush low voltage and brush high voltage c) to help maintain a more constant brush voltage d) none of the above . Which of the following is/are a type of DC generator armature winding configuration? a) lap b) wave c) frogleg d) all of the abovearrow_forwardA shunt generator delivers 195 Amp of terminal of voltage 250Volts. The armature resistance and shuntfield resistance are 0.02 ohm and 50 ohms respectively. The iron and friction losses equal to 950 Watts.The overall efficiency is?arrow_forward
- What is the answer for Question 13?arrow_forward1. It is a machine that converts mechanical energy to electrical energy. 2. It is a machine that converts electrical energy to mechanical energy. 3. It is cylindrical or drum-shaped where the coils are placed and can either be lap wounded or wave wounded. 4. It connects the commutator to the other parts of the DC machine. 5. It serves as the housing of the dc machine. 6. True or False: The shunt field winding is part of the armature. 7. True or False: The long shunt compound generator is when the armature is in series with the series field winding and parallel to the shunt field winding. 8-10. Your newly built house needs an elevator. Which from the following will be best to use- series, shunt or compound motor and why?arrow_forwardExplain, in details, why it is necessary to use starting resistance?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Delmar's Standard Textbook Of ElectricityElectrical EngineeringISBN:9781337900348Author:Stephen L. HermanPublisher:Cengage Learning
Electricity for Refrigeration, Heating, and Air C...Mechanical EngineeringISBN:9781337399128Author:Russell E. SmithPublisher:Cengage Learning
Delmar's Standard Textbook Of Electricity
Electrical Engineering
ISBN:9781337900348
Author:Stephen L. Herman
Publisher:Cengage Learning
Electricity for Refrigeration, Heating, and Air C...
Mechanical Engineering
ISBN:9781337399128
Author:Russell E. Smith
Publisher:Cengage Learning
How Electric Motors Work - 3 phase AC induction motors ac motor; Author: The Engineering Mindset;https://www.youtube.com/watch?v=59HBoIXzX_c;License: Standard Youtube License