Solve Prob. 3.55, assuming that the shaft AB is replaced by a hollow shaft of the same outer diameter and 25-mm inner diameter.
3.55 Two solid steel shafts (G = 77.2 GPa) are connected to a coupling disk B and to fixed supports at A and C. For the loading shown, determine (a) the reaction at each support, (b) the maximum shearing stress in shaft (c) the maximum shearing stress in shaft BC.
Fig. p3.55
(a)
The reaction at the supports.
Answer to Problem 56P
The reaction at the supports are
Explanation of Solution
Given information:
The modulus of rigidity of solid shafts is
Inner diameter of the shaft AB is 25 mm.
Calculation:
The outer radius of the shaft AB is
The inner radius of the shaft AB is
The polar moment of inertia of shaft AB of outer radius
The torque carried by the shaft AB
Here,
Substitute
The radius of the shaft BC is
The polar moment of inertia of shaft BC of radius
The torque carried by the shaft BC
Here,
Substitute
The value of total torque in the shaft is
The total torque
Substitute
Substitute
Therefore, the reaction at the supports are
(b)
The maximum shearing stress in the shaft AB.
Answer to Problem 56P
The maximum shearing stress in the shaft AB is
Explanation of Solution
Given information:
The modulus of rigidity of solid shafts is
Calculation:
Refer (a).
The value of torque in the shaft AB is
The polar moment of inertia of shaft AB is
The maximum shearing stress in the shaft AB
Substitute
Therefore, the maximum shearing stress in the shaft AB is
(c)
The maximum shearing stress in the shaft BC.
Answer to Problem 56P
The maximum shearing stress in the shaft BC is
Explanation of Solution
Given information:
The modulus of rigidity of solid shafts is
Calculation:
Refer (a).
The value of torque in the shaft BC is
The polar moment of inertia of shaft BC of radius
The maximum shearing stress in the shaft BC
Substitute
Therefore, the maximum shearing stress in the shaft BC is
Want to see more full solutions like this?
Chapter 3 Solutions
EBK MECHANICS OF MATERIALS
- Two solid steel shafts (G = 77.2 GPa) are connected to a coupling disk B and to fixed supports at A and C. For the loading shown, determine (a) the reaction at each support, (b) the maximum shearing stress in shaft AB, (c) the maximum shearing stress in shaft BC. A 200 mm B 50 mm 250 mm 38 mm 1.4 kN. marrow_forwardProblem 3.56arrow_forward3. A shaft composed of segments AC, CD and DB is fastened to rigid walls and loaded as shown. For bronze G = 35 GPa, for aluminum G = 28 GPA, and for steel G=83 GPa. Tc = 300 N.m T₁ = 700 N-m C Aluminum D A Bronze Steel 25 mm 25 mm 50 mm ◊ 2 m 2 m 2.5 m Determine: (a) FBD of the composite shaft showing T (N-m) vs. axial distance (b) the maximum shearing stress (MPa) developed in segment AC (c) the maximum shearing stress (MPa) developed in segment CD (d) the maximum shearing stress (MPa) developed in segment DB (e) angle of twist (deg) of point C w.r.t. A, OC/A (f) angle of twist (deg) of point D w.r.t. C, D/C ~3~arrow_forward
- 2.14 The aluminum rod ABC (E 10.1 × 106 psi), which consists of two cylindrical portions AB and BC, is to be replaced with a cylin- drical steel rod DE (E = 29 × 106 psi) of the same overall length. Determine the minimum required diameter d of the steel rod if its vertical deformation is not to exceed the deformation of the aluminum rod under the same load and if the allowable stress in the steel rod is not to exceed 24 ksi. Ĵ 12 in. + 18 in. 28 kips -1.5 in. Fig. P2.14 B -2.25 in. 28 kips D E --arrow_forwardIn the mechanism shown below, the distributed load W is 300 N/m and the angle 0 is 35", knowing that link AB has 1.5cm x 1.5cm cross-section. W |C 1.5 m 1-What is the average normal stress at section b-b?arrow_forwardProblem 3.54, not 3.55, problem 3.54arrow_forward
- 3.38 The aluminum rod AB (G = 27 GPa) is bonded to the brass rod BD (G = 39 GPa). Knowing that portion CD of the brass rod is hollow and has an inner diameter of 40 mm, determine the angle of twist at A. 60 mm T = 1600 N m 36 mm TA = S00 N - mn 250 mm B 375 mm A 400 mm Fig. P3.38arrow_forward3.6 Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is 20 mm. Determine the largest allowable value of P if the shear stress in the shaft is not to exceed 120 MPa and its angle of twist is limited to 7°. Use G= 80 GPa for steel. 300 mm B 500 mm FIG. P3.6arrow_forwardV3arrow_forward
- 3.11 Knowing that each of the shafts AB, BC, and CD consists of a solid circular rod, determine (a) the shaft in which the maximum shear- ing stress occurs, (b) the magnitude of that stress. 48 N. m 144 N. m A Fig. P3.11 and P3.12 dAB 60 Nm B = 15 mm dBC C = 18 mm D dcp = 21 mmarrow_forwardSolve using method of forces and then separately by method of displacements, using matrix form: Two cylindrical rods, one of steel and the other of brass, are joined at C and restrained by rigid supports at A and E. Knowing the loading shown and using Es = 200 GPa, E, = 105 GPa determine the reactions and A and E and the displacements of B, C, D. 100 100 Steel B. Bras 60 kN 40 kN 40-mm dlam. 30-mm diam.arrow_forward1. The member BD is attached to a rod at B, to a hydraulic cylinder at C, and to a fixed support at D. The bolt used at D acts in double shear and is made from a steel for which the maximum allowable shearing stress is Tallow = 40 ksi. The rod AB is made of a steel for which the maximum allowable tensile stress is Oallow = 60 ksi. The upward hydraulic force applied at C is 12 kip. 1) Calculate the minimum diameter of the rod AB. 2) Calculate the minimum diameter of the bolt at D. B FAB 12 kip 8 in. FBDarrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY