
Perform the following estimations without using a calculator.
- Estimate the mass of water (kg) in an Olympic-size swimming pool.
- A drinking glass is being filled from a pitcher. Estimate die mass flow rate of the water (g/s).
- Twelve male heavyweight boxers coincidentally get on the same elevator in Great Britain. Posted on the elevator wall is a sign that gives the maximum safe combined weight of the passengers, Wmax, in stones. (A stone is a unit of mass equal to 14 lbm. It is commonly used in England as a measure of body weight, which, like the numerical equivalence between the lbm and lbf, is only valid at or near sea level.) If you were one of the boxers, estimate the lowest value of Wniaxfor which you would feel comfortable remaining on the elevator.
- The Trans-Alaska Pipeline has an outside diameter of 4 ft and extends 800 miles from the North Slope of Alaska to the northernmost ice-free port in Valdez, Alaska. How many barrels of oil arc required to fill the pipeline?
- Estimate the volume of your body (cm3) in two different ways. (Show your work.)
- A solid block is dropped into water and very slowly sinks to the bottom. Estimate its specific gravity.

(a)
Interpretation:
The mass of water (kg) in an Olympic-size pool should be estimated.
Concept introduction:
The density is the ratio of mass and volume given as:
Here, m is mass and V is volume
Answer to Problem 3.1P
Explanation of Solution
Let,
The size of a pool is
The density of water is
Since, the formula for density is:
Thus,
The mass of water is:

(b)
Interpretation:
The mass flow rate of the water (g/s) should be estimated.
Concept introduction:
An arithmetical multiplier which is used for converting a quantity expressed in one unit into another equivalent set of units is said to be conversion factor.
The relationship between US and SI units are,
Answer to Problem 3.1P
Explanation of Solution
We can assume that the pitcher is a ‘large jug’.
In US standard system the volume of a drinking water glass is 8 oz and we can assume that the glass can be filled within 2 seconds using the pitcher.
The answer can be calculated as:

(c)
Interpretation:
The lowest value of maximum weight (Wmax) for which you would feel comfortable remaining on the elevator should be estimated.
Concept introduction:
An arithmetical multiplier which is used for converting a quantity expressed in one unit into another equivalent set of units is said to be conversion factor. A stone is a unit of mass equal to 14 lbm.
Answer to Problem 3.1P
220 stones.
Explanation of Solution
A boxer who weight 220 lbm or above is considered as the boxer in heavy weight category.
The weight of a boxer can be considered as 220 lbm.
So calculate the minimum weight,
Where

(d)
Interpretation:
The number of barrels of oil required to fill the pipeline should be calculated.
Concept introduction:
The pipeline has an outside diameter of 4 ft and extends 800 miles.
The volume of a pipe (V) is given by,
Where, D = diameter of the pipe and L = length of the pipe
Answer to Problem 3.1P
Explanation of Solution
Let,
There are 42 gals in 1 barrel.
1 mile = 5880 ft
So the number of barrels in the pipe line can be calculated as,

(e)
Interpretation:
The volume of your body should be estimated in two different ways.
Concept introduction:
The density is the ratio of mass and volume given as:
Here, m is mass and V is volume
Answer to Problem 3.1P
The answer is
Explanation of Solution
Given Information:
The volume of the person is
Calculation:
Method 1:
Assume that the volume of the person can be considered as,
Height = 6 ft, width = 1 ft, thickness (distance between heal and toe) = 0.5 ft
Unit conversion,
1 ft3= 28 317 cm3
The volume of the person,
Method 2:
Assume,
The weight of the person to be 150 lbm
The density of the person to be 62.4 lbm / ft3
Volume = mass / density
The volume of the person,

(f)
Interpretation:
The specific gravity of a solid block in water should be calculated.
Concept introduction:
The specific gravity of a body with respect to water is calculated by taking ratio of density of that body to the density of water. It is also related to molar mass as follows:
Here,
Answer to Problem 3.1P
Explanation of Solution
Since, the solid block sinks into the water very slowly, the density of block should be close to the density of water. So, assume density of the block to be 1050 kg / m3.
The Specific gravity is calculated as follows:
Putting the values,
Want to see more full solutions like this?
Chapter 3 Solutions
ELEM.PRIN.OF CHEMICAL PROC.-W/ACCESS
Additional Engineering Textbook Solutions
Java: An Introduction to Problem Solving and Programming (8th Edition)
Concepts Of Programming Languages
Electric Circuits. (11th Edition)
Computer Science: An Overview (13th Edition) (What's New in Computer Science)
Database Concepts (8th Edition)
Degarmo's Materials And Processes In Manufacturing
- Can you provide me the answer of these pleasearrow_forwardA constant-volume process involving 2.0 moles of diatomic ideal gas, for which cV = (5/2)R, is at an initial state of 111 kPa and 277 K and is then heated reversibly to 356 K. Calculate the P2 (kPa), dU (kJ), heat transfer q (kJ mol–1), and w (kJ mol–1).arrow_forwardProblem 1 Marks: 60 Section: 1a): 30 marks, Section 1b):30 marks A laboratory scale fluidized bed is considered for studying a catalytic ozone decomposition. a) It is requested to derive model equations under the following assumptions: ■ Operation of the catalytic reactor under steady state conditions, There is no influence of thermal ozone decomposition reactions. The fluidized bed includes bubbles and dense phase. □ The dense phase can be simulated using a CSTR The fluidized bed bubbles contain catalyst particles and can be simulated as a DSTR (batch). □ The jets contain particles and can be simulated with a PFR. The influence of the freeboard has to be considered using a PFR model. The available catalytic reaction rate model is r (moles/gcat.s)= -k CA b) Same than on a) under unsteady state conditions, using an absorbable and reactive tracer. Note: A step-by step derivation of the model equations is required here. A quick answer will not do. Problem 2 Marks: 40 Section 2a: 30 marks,…arrow_forward
- Penicillin process Penicillium chrysogenum is used to produce penicillin in a 90,000-litre fermenter. The volumetric rate of oxygen uptake by the cells ranges from 0.45 to 0.85 mmol l^−1 min^−1 depending on time during the culture. Power input by stirring is 2.9 W l^−1. Estimate the cooling requirements.arrow_forwardProduction of bakers’ yeast Bakers’ yeast is produced in a 50,000-litre fermenter under aerobic conditions. The carbon substrate is sucrose; ammonia is provided as the nitrogen source. The average biomass composition is CH_1.83O_0.55N_0.17 with 5% ash. Under conditions supporting efficient growth, biomass is the only major product and the biomass yield from sucrose is 0.5 g g^−1. If the specific growth rate is 0.45 h^−1, estimate the rate of heat removal required to maintain constant temperature in the fermenter when the yeast concentration is 10 g l^−1.arrow_forwardSensible energy change Calculate the enthalpy change associated with the following processes:(a) m-Cresol is heated from 25°C to 100°C(b) Ethylene glycol is cooled from 20°C to 10°C(c) Succinic acid is heated from 15°C to 120°C(d) Air is cooled from 150°C to 65°Carrow_forward
- ▼ Enzyme conversion An immobilised enzyme process is used in an ice-cream factory to hydrolyse lactose (C12H22O11) to glucose (C6H12O6) and galactose (C6H1206): C12H22O11 + H2O →→ C6H12O + C6H12O6 Gel beads containing ß-galactosidase are packed into a column reactor; 2500 kg of lactose enters the reactor per day as a 10% solution in water at 25°C. The reactor operates at steady state and 32°C; all of the lactose is converted. Because the heat of reaction for enzyme conversions is not as great as for cell culture, sensible heat changes and heats of mixing cannot be ignored. Lactose Water Ah (kJ gmol¹) C, (cal g¹ ºC-¹) Ahm (kcal gmol¹) 3.7 -5652.5 0.30 1.0 Glucose -2805.0 0.30 5.6 Galactose -2805.7 0.30 5.6 (a) What is the standard heat of reaction for this enzyme conversion? (b) Estimate the heating or cooling requirements for this process. State explicitly whether heating or cooling is needed.arrow_forwardBacterial production of alginate Azotobacter vinelandii is investigated for production of alginate from sucrose. In a continuous fermenter at 28°C with ammonia as nitrogen source, the yield of alginate was found to be 4 g g^−1 oxygen consumed. It is planned to produce alginate at a rate of 5 kg h^−1. Since the viscosity of alginate in aqueous solution is considerable, energy input due to mixing the broth cannot be neglected. The fermenter is equipped with a flat-blade disc turbine; at a satisfactory mixing speed and air flow rate, the power requirements are estimated at 1.5 kW. Calculate the cooling requirements.arrow_forwardPreheating nutrient medium Steam is used to heat nutrient medium in a continuous-flow process. Saturated steam at 150°C enters a coil on the outside of the heating vessel and is completely condensed. Liquid medium enters the vessel at 15°C and leaves at 44°C. Heat losses from the jacket to the surroundings are estimated as 0.22 kW. If the flow rate of medium is 3250 kg h^−1 and its heat capacity is 0.9 cal g^−1 °C^−1, how much steam is required?arrow_forward
- Q3] Determine the optimal operating conditions (XA, t, and CR) in a mixed flow reactor to maximize the concentration of R (CR) in the effluent, where an aqueous feed A with an initial concentration of CA0-40 mol/m³ enters the reactor, undergoes decomposition, and exits as a mixture containing A, R, and S. K₁ AR, FR = k₁C, k₁ = 0.4 m³/(mol min) SA AS, rs = k₂CA, k₂ = 2(min), CA0 = 40 mol/m³arrow_forwardConsider the parallel decomposition of A of different orders with FR = 1, rs = 2CA and IT = C. Determine the maximum concentration of desired product obtainable in mixed flow reactor and plug flow reactor. (1) R is desired product and CA0 = 2. (2) S is desired product and CA0 = 4. R S Tarrow_forward1. Copper is known to be toxic to fish, and in particular, the free ion Cu²+ species typically shows greatest toxicity. a. Calculate the speciation of Cu(II) for freshwater at a pH value of 8.3 as the hardness increases from 20 (soft) to 100 (moderately hard) to 200 (very hard) mg/L as CaCO3. Assume that the total divalent Cu(II) concentration is 10 µg/L. b. Based on your findings in part (a), do you think it is appropriate to set a single regulatory limit or should it depend on variables such as pH and hardness? Explain your answer.arrow_forward
- Introduction to Chemical Engineering Thermodynami...Chemical EngineeringISBN:9781259696527Author:J.M. Smith Termodinamica en ingenieria quimica, Hendrick C Van Ness, Michael Abbott, Mark SwihartPublisher:McGraw-Hill EducationElementary Principles of Chemical Processes, Bind...Chemical EngineeringISBN:9781118431221Author:Richard M. Felder, Ronald W. Rousseau, Lisa G. BullardPublisher:WILEYElements of Chemical Reaction Engineering (5th Ed...Chemical EngineeringISBN:9780133887518Author:H. Scott FoglerPublisher:Prentice Hall
- Industrial Plastics: Theory and ApplicationsChemical EngineeringISBN:9781285061238Author:Lokensgard, ErikPublisher:Delmar Cengage LearningUnit Operations of Chemical EngineeringChemical EngineeringISBN:9780072848236Author:Warren McCabe, Julian C. Smith, Peter HarriottPublisher:McGraw-Hill Companies, The





