DeGarmo's Materials and Processes in Manufacturing
12th Edition
ISBN: 9781118987674
Author: J. T. Black, Ronald A. Kohser
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 23, Problem 5P
Calculate the metal removal rate for machining at a speed of 80 fpm, feed of 0.030 ipr, at a depth of 0.625 in. Use any data from Problem 4 that you need.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
In an orthogonal cutting operation an 8 mm deep groove is to be turned on a 50 mm diameter steel bar. Spindle speed is 300 rpm and a feed rate of 0.25 mm/rev is given to the tool. Produced chips have a width of 2 mm. Calculate the material removal rate at the beginning and at the end of the cut.
Can u help me please?
Whats the answer for this please ?
None
Chapter 23 Solutions
DeGarmo's Materials and Processes in Manufacturing
Ch. 23 - How is the tool-work relationship in turning...Ch. 23 - What different kinds of surfaces can be produced...Ch. 23 - How does form turning differ from ordinary...Ch. 23 - What is the basic difference between facing and a...Ch. 23 - Which operations shown in Figure 23.3 do not form...Ch. 23 - Why is it difficult to make heavy cuts if a form...Ch. 23 - Show how equation 23.6 is an approximate equation.Ch. 23 - Why is the spindle of the lathe hollow?Ch. 23 - What function does a lathe carriage have?Ch. 23 - Why is feed specified for a boring operation...
Ch. 23 - Why are depths of cut in boring usually smaller...Ch. 23 - How can work be held and supported in a lathe?Ch. 23 - How is a workpiece that is mounted between centers...Ch. 23 - What will happen to the workpiece when turned, if...Ch. 23 - Why is it not advisable to hold hot-rolled steel...Ch. 23 - How does a steady rest differ from a follow rest?Ch. 23 - What are the advantages and disadvantages of a...Ch. 23 - Why should the distance the cutting tool overhangs...Ch. 23 - Prob. 19RQCh. 23 - How can a tapered part be turned on a lathe?Ch. 23 - Why might it be desirable to use a heavy depth of...Ch. 23 - If the rpm for a facing cut (assuming given work...Ch. 23 - Why is it usually necessary to take relatively...Ch. 23 - How does the corner radius of the tool influence...Ch. 23 - What effect does a BUE have on the diameter of the...Ch. 23 - How does the multiple-spindle screw machine differ...Ch. 23 - Why does boring ensure concentricity between the...Ch. 23 - Why are vertical spindle machines better suited...Ch. 23 - Prob. 29RQCh. 23 - Prob. 30RQCh. 23 - In which figures in this chapter is a dead center...Ch. 23 - Prob. 32RQCh. 23 - In which figures in this chapter showing setups do...Ch. 23 - How many form tools are being utilized in the...Ch. 23 - Prob. 35RQCh. 23 - Select the speed, feed, and depth of cut for...Ch. 23 - Calculate the rpm NS to run the spindle on a lathe...Ch. 23 - The lathe in problem 2 has rpm settings of 20, 30,...Ch. 23 - Calculate the cutting time if the length of cut is...Ch. 23 - Calculate the metal removal rate for machining at...Ch. 23 - Determine the speed, feed, and depth of cut when...Ch. 23 - At a speed of 90 fpm, feed of 0.030 ipr, and depth...Ch. 23 - Calculate the cutting time for a 4-in. length of...Ch. 23 - For a boring operation at V=90,fr=0.030, and...Ch. 23 - A cutting speed of 100 sfpm has been selected for...Ch. 23 - The following data apply for machining a part on a...Ch. 23 - A finish cut for a length of 10 in. on a diameter...Ch. 23 - A workpiece 10 in. in diameter is to be faced down...Ch. 23 - A hole 89 mm in diameter is to be drilled and...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
A cylinder that is 500 mm in diameter and 2.0 m long has a specific weight of 535N/m3. It is held down into pos...
Applied Fluid Mechanics (7th Edition)
What parts are included in the vehicle chassis?
Automotive Technology: Principles, Diagnosis, and Service (5th Edition)
Determine the magnitude of the velocity of point B at the instant shown.
Engineering Mechanics: Dynamics (14th Edition)
F47. Determine the resultant moment produced by the forces about point O.
INTERNATIONAL EDITION---Engineering Mechanics: Statics, 14th edition (SI unit)
If F = {350i 250j 450k} N and cable AB is 9 m long, determine the x, y, z coordinates of point A. Prob. 2-89
Engineering Mechanics: Statics
What parts are included in the vehicle chassis?
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- hand write asap ( i'll give you multiple upvotearrow_forwardFind the machining time required to turn a mild steel rod from 65mm to 58 mm over a length of 100 mm by using a carbide insert. If the approach length and over run length is taken as 5 mm, Cutting speed as 20 m/min and feed is =0.2 mm/rev, and the depth of cut is 0.5mmarrow_forwardIn turning of stales steel alloy, 1100 mm length and 400 mm diameter, the Feed was 0.35 mm/rev, and depth of cut = 2.5 mm. The tool used in this cutting is cemented carbide tool where Taylor tool life parameters are n = 0.24 and C = 450 (tool life (min) and cutting speed (m/min). Compute the cutting speed that will allow the tool life to be 10% longer than the machining time for this part.arrow_forward
- A shaper is operated at 120 cutting strokes per minute and is used to machine a work piece of 250 mm in length and 120 mm wide. Use a feed of 0.6 mm per stroke and a depth of cut of 6 mm. Calculate the total machining time to for machining the component. If the forward stroke is completed in 230°, calculate the percentage of the time when the tool is not contacting the work piece.arrow_forwardi need the answer quicklyarrow_forwardIn orthogonal machining operation the chip thickness and the uncut chip thickness are equal to 0.45 mm. If the tool rake and is 0 deg. What is the shear plane angle?arrow_forward
- Calculate spindle RPM and machining time for cutting a 1.5" diameter 4" long at 225 SFPM using a feed rate of 0.004".arrow_forwardplz solve 15 mins i'll give you multiple upvote..hand writearrow_forwardA drilling operation is performed to create a through hole on a steel plate that is 20 mm thick. Cutting speed = 0.4 m/s, and feed = 0.20 mm/rev. The 18-mm-diameter twist drill has a point angle of 120°. Determine the following once the drill reaches full diameter: a. the machining time and, b. the metal removal rate Equation used Tm TD₂L fvarrow_forward
- Need accurate answer for this pleasearrow_forwardDetermine the total machining time for a workpiece 30mm in diameter and the required length is 145 mm. Other data: Material: 38mm dia. X 149 mm Depth of cut (turning): 4mm Depth of cut (facing): 2mm Feed : 0.05 mm/rev : 35 SMPM Cutting speedarrow_forwardDuring orthogonal cutting of MS with a 10 ° rake angle tool, the chip thickness ratio was obtained as 0.4. Calculate shear anglearrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Precision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
The Most Common Metal Machining Processes (Metal Machining Video 1); Author: Sofeast Ltd;https://www.youtube.com/watch?v=uxVJ3qtezGw;License: Standard YouTube License, CC-BY
Machining process and Machine Tools; Author: Amar Gandhi;https://www.youtube.com/watch?v=X2mUJ8baaE0;License: Standard Youtube License