Degarmo's Materials And Processes In Manufacturing
13th Edition
ISBN: 9781119492825
Author: Black, J. Temple, Kohser, Ronald A., Author.
Publisher: Wiley,
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 23, Problem 1RQ
How is the tool-work relationship in turning different from that in facing?
Expert Solution & Answer
To determine
The reason of tool work relationship in turning different from the facing.
Explanation of Solution
In turning operation, the workpiece is rotated with a fixed velocity, and it is mounted on a work-holding device named as chuck. In this operation, feed is provided to the cutting tool along with parallel to the axis of the workpiece. The cutting tool used in turning is named as a single-point cutting tool.
While in facing, the workpiece is the same rotated on the work holding device, but here the tool used is facing tool, and its movement along the workpiece is perpendicular to the workpiece. The facing tool, which is wider than the depth of cut, is only used for end facing operation.
Want to see more full solutions like this?
Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
Step by step solution please
I need answer correctly and fast please its urgent
Need answer quickly
Chapter 23 Solutions
Degarmo's Materials And Processes In Manufacturing
Ch. 23 - How is the tool-work relationship in turning...Ch. 23 - What different kinds of surfaces can be produced...Ch. 23 - How does form turning differ from ordinary...Ch. 23 - What is the basic difference between facing and a...Ch. 23 - Which operations shown in Figure 23.3 do not form...Ch. 23 - Why is it difficult to make heavy cuts if a form...Ch. 23 - Show how equation 23.6 is an approximate equation.Ch. 23 - Why is the spindle of the lathe hollow?Ch. 23 - What function does a lathe carriage have?Ch. 23 - Why is feed specified for a boring operation...
Ch. 23 - Why are depths of cut in boring usually smaller...Ch. 23 - How can work be held and supported in a lathe?Ch. 23 - How is a workpiece that is mounted between centers...Ch. 23 - What will happen to the workpiece when turned, if...Ch. 23 - Why is it not advisable to hold hot-rolled steel...Ch. 23 - How does a steady rest differ from a follow rest?Ch. 23 - What are the advantages and disadvantages of a...Ch. 23 - Why should the distance the cutting tool overhangs...Ch. 23 - Prob. 19RQCh. 23 - How can a tapered part be turned on a lathe?Ch. 23 - Why might it be desirable to use a heavy depth of...Ch. 23 - If the rpm for a facing cut (assuming given work...Ch. 23 - Why is it usually necessary to take relatively...Ch. 23 - How does the corner radius of the tool influence...Ch. 23 - What effect does a BUE have on the diameter of the...Ch. 23 - How does the multiple-spindle screw machine differ...Ch. 23 - Why does boring ensure concentricity between the...Ch. 23 - Why are vertical spindle machines better suited...Ch. 23 - Prob. 29RQCh. 23 - Prob. 30RQCh. 23 - In which figures in this chapter is a dead center...Ch. 23 - Prob. 32RQCh. 23 - In which figures in this chapter showing setups do...Ch. 23 - How many form tools are being utilized in the...Ch. 23 - Prob. 35RQCh. 23 - Select the speed, feed, and depth of cut for...Ch. 23 - Calculate the rpm NS to run the spindle on a lathe...Ch. 23 - The lathe in problem 2 has rpm settings of 20, 30,...Ch. 23 - Calculate the cutting time if the length of cut is...Ch. 23 - Calculate the metal removal rate for machining at...Ch. 23 - Determine the speed, feed, and depth of cut when...Ch. 23 - At a speed of 90 fpm, feed of 0.030 ipr, and depth...Ch. 23 - Calculate the cutting time for a 4-in. length of...Ch. 23 - For a boring operation at V=90,fr=0.030, and...Ch. 23 - A cutting speed of 100 sfpm has been selected for...Ch. 23 - The following data apply for machining a part on a...Ch. 23 - A finish cut for a length of 10 in. on a diameter...Ch. 23 - A workpiece 10 in. in diameter is to be faced down...Ch. 23 - A hole 89 mm in diameter is to be drilled and...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
Find the magnitude of the projected component of the force along the pipe AO.
INTERNATIONAL EDITION---Engineering Mechanics: Statics, 14th edition (SI unit)
The inclined-tube manometer shown has D = 76 mm and d = 8 mm, and is filled with Meriam red oil. Compute the an...
Fox and McDonald's Introduction to Fluid Mechanics
What parts are included in the vehicle chassis?
Automotive Technology: Principles, Diagnosis, and Service (5th Edition)
During an engine test on the ground, a propeller thrust T=3000N is generated on the 1800-kg air-plane with mass...
Engineering Mechanics: Statics
1.1 What is the difference between an atom and a molecule? A molecule and a crystal?
Manufacturing Engineering & Technology
Determine the normal stress in each member of the truss structure. All joints are ball joint, and the material ...
Introduction To Finite Element Analysis And Design
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- What machine tool is available with either horizontal or vertical spindle orientation and uses rotating cutting tools to primarily produce flat surfaces?arrow_forwardMake a comprehensive write up on tool-wear and tool life with due reference to cutting speed and tool life. ( Manufacturing process)arrow_forward1 . Built-up edge is generated on the surface of workpart ? 2. hardening occurs due to generated high temperature and pressure between work and tool ? 3. Tool life is usually measured in days ?arrow_forward
- Suppose you have a turning operation using a tool with a zero back rake and 5° end relief. The insert flank has a wear land on it of 0.020 in. How much has the diameter of the workpiece grown (increased) due to this flank wear, assuming the tool has not been reset to compensate for the flank wear?arrow_forwardIn a production turning operation, the workpart is 60 mm in diameter and 500 mm long. A feed of 0.75 mm/rev is used in the operation. If cutting speed-9 m/s, the tool must be changed every 4 workparts; But if cutting speed=5 m/s, the tool can be used to produce 50 pieces between tool changes. Determine the Taylor tool life equation for this job. (use the equations given below for solution) L Tm- 1,= Nf N AD, vT" = C %3| AD,L Tm fvarrow_forwardFor pocket operation of 2 x 3 inch surface and dept of 0.06 in using 0.5 in end mill tool. What is the time required to finished a cut when the depth of cut is 0.3 inch and the feed rate 0.05 inch/rev, spindle RPM is 60. The subject is Machine Shop Theory. Please make clear the solution and answer and understandable. Thanksarrow_forward
- Explain any one of the turning operations in terms of tool shape,tool path, final and generated geometry, possible tolerances. Then list possible applications or products that are made using that operation.arrow_forwardI need correct answer onlyarrow_forwardIn a production turning operation, the workpart is 60 mm in diameter and 500 mm long. A feed of 0.75 mm/rev is used in the operation. If cutting speed=9 m/s, the tool must be changed every 4 workparts; But if cutting speed=5 m/s, the tool can be used to produce 50 pieces between tool changes. Determine the Taylor tool life equation for this job. (use the equations given below for solution)arrow_forward
- In addition to cutting speed, what other cutting variables are included in the expanded version of the Taylor tool life equation?arrow_forwardThree tool materials are to be compared for the same finish turning operation on a batch of 100 steel parts: high speed steel, cemented carbide, and ceramic. For the high speed steel tool, the 170 Taylor equation parameters are: n = 0.125 and C = 70. The price of the HSS tool is $15.00 and it is estimated that it can be ground and reground 15 times at a cost of $1.50. Tool change time = 3 min. Both carbide and ceramic tools are in insert form and can be held in the same mechanical toolholder. The Taylor equation parameters for the cemented carbide are: n = 0.25 and C = 500; and for the ceramic: n = 0.6 and C = 3,000. The cost per insert for the carbide = $6.00 and for the ceramic = $8.00. Number of cutting edges per insert in both cases = 6. Tool change time = 1.0 min for both tools. Time to change parts = 2.0 min. Feed = 0.25 mm/rev, and depth = 3.0 mm. The cost of machine time = $30/hr. The part dimensions are: diameter = 56.0 mm and length = 290 mm. Setup time for the batch is 2.0…arrow_forward1. In a production turning operation, the cylindrical workpiece is 425 mm long and 190 mm in diameter, Feed 0.30 mm/rev. What cutting speed must be used to achieve a machining time of 7.0 min?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Precision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
The Most Common Metal Machining Processes (Metal Machining Video 1); Author: Sofeast Ltd;https://www.youtube.com/watch?v=uxVJ3qtezGw;License: Standard YouTube License, CC-BY
Machining process and Machine Tools; Author: Amar Gandhi;https://www.youtube.com/watch?v=X2mUJ8baaE0;License: Standard Youtube License