Explain why continuous chips are not necessarily desirable.

Question

Want to see more full solutions like this?

Answer 1

Textbook Question

Chapter 21, Problem 1RQ

Explain why continuous chips are not necessarily desirable.

Expert Solution & Answer

To determine

Explain why continuous chips are not necessarily desirable.

Explanation of Solution

In computer-controlled machine tools, continuous chips are not preferred. This is because they can get tangled around the tool holder, fixture or even the workpiece. It can also get tangled into the chip disposal system. To clear these chips, it is possible that the operation may be needed to halted.

This problem can be resolved if we use chip breakers. The cutting speed can be changed, or the feed, depth of cut can be varied. It can also be solved by using cutting fluids.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Students have asked these similar questions

Please draw the section view of the following problems

7) Please draw the front, top and side view for the following object. Please cross this line out

A 10-kg box is pulled along P,Na rough surface by a force P, as shown in thefigure. The pulling force linearly increaseswith time, while the particle is motionless att = 0s untilit reaches a maximum force of100 Nattimet = 4s. If the ground has staticand kinetic friction coefficients of u, = 0.6 andHU, = 0.4 respectively, determine the velocityof the A 1 0 - kg box is pulled along P , N a rough surface by a force P , as shown in the figure. The pulling force linearly increases with time, while the particle is motionless at t = 0 s untilit reaches a maximum force of 1 0 0 Nattimet = 4 s . If the ground has static and kinetic friction coefficients of u , = 0 . 6 and HU , = 0 . 4 respectively, determine the velocity of the particle att = 4 s .

Answer 2

Textbook Question

Chapter 21, Problem 1RQ

Explain why continuous chips are not necessarily desirable.

Expert Solution & Answer

To determine

Explain why continuous chips are not necessarily desirable.

Explanation of Solution

In computer-controlled machine tools, continuous chips are not preferred. This is because they can get tangled around the tool holder, fixture or even the workpiece. It can also get tangled into the chip disposal system. To clear these chips, it is possible that the operation may be needed to halted.

This problem can be resolved if we use chip breakers. The cutting speed can be changed, or the feed, depth of cut can be varied. It can also be solved by using cutting fluids.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 3

Textbook Question

Chapter 21, Problem 1RQ

Explain why continuous chips are not necessarily desirable.

Expert Solution & Answer

To determine

Explain why continuous chips are not necessarily desirable.

Explanation of Solution

In computer-controlled machine tools, continuous chips are not preferred. This is because they can get tangled around the tool holder, fixture or even the workpiece. It can also get tangled into the chip disposal system. To clear these chips, it is possible that the operation may be needed to halted.

This problem can be resolved if we use chip breakers. The cutting speed can be changed, or the feed, depth of cut can be varied. It can also be solved by using cutting fluids.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 4

Textbook Question

Chapter 21, Problem 1RQ

Explain why continuous chips are not necessarily desirable.

Expert Solution & Answer

To determine

Explain why continuous chips are not necessarily desirable.

Explanation of Solution

In computer-controlled machine tools, continuous chips are not preferred. This is because they can get tangled around the tool holder, fixture or even the workpiece. It can also get tangled into the chip disposal system. To clear these chips, it is possible that the operation may be needed to halted.

This problem can be resolved if we use chip breakers. The cutting speed can be changed, or the feed, depth of cut can be varied. It can also be solved by using cutting fluids.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 5

Textbook Question

Answer 6

Textbook Question

Answer 7

Expert Solution & Answer

To determine

Explain why continuous chips are not necessarily desirable.

Explanation of Solution

In computer-controlled machine tools, continuous chips are not preferred. This is because they can get tangled around the tool holder, fixture or even the workpiece. It can also get tangled into the chip disposal system. To clear these chips, it is possible that the operation may be needed to halted.

This problem can be resolved if we use chip breakers. The cutting speed can be changed, or the feed, depth of cut can be varied. It can also be solved by using cutting fluids.

Answer 8

Expert Solution & Answer

To determine

Explain why continuous chips are not necessarily desirable.

Explanation of Solution

In computer-controlled machine tools, continuous chips are not preferred. This is because they can get tangled around the tool holder, fixture or even the workpiece. It can also get tangled into the chip disposal system. To clear these chips, it is possible that the operation may be needed to halted.

This problem can be resolved if we use chip breakers. The cutting speed can be changed, or the feed, depth of cut can be varied. It can also be solved by using cutting fluids.

Answer 9

Expert Solution & Answer

Answer 10

Expert Solution & Answer

Answer 11

To determine

Explain why continuous chips are not necessarily desirable.

Answer 12

Explanation of Solution

In computer-controlled machine tools, continuous chips are not preferred. This is because they can get tangled around the tool holder, fixture or even the workpiece. It can also get tangled into the chip disposal system. To clear these chips, it is possible that the operation may be needed to halted.

This problem can be resolved if we use chip breakers. The cutting speed can be changed, or the feed, depth of cut can be varied. It can also be solved by using cutting fluids.

Answer 13

Ch. 21 - Explain why continuous chips are not necessarily...Ch. 21 - Name the factors that contribute to the formation...Ch. 21 - What is the cutting ratio? Is it always less than...Ch. 21 - Explain the difference between positive and...Ch. 21 - Explain how a dull tool can lead to negative rake...Ch. 21 - Comment on the role and importance relief angle.Ch. 21 - Explain the difference between discontinuous chips...Ch. 21 - Why should we be interested in the magnitude of...Ch. 21 - What are the differences between orthogonal and...Ch. 21 - What is a BUE? Why does it form?

Explain why continuous chips are not necessarily desirable.

Concept explainers

Videos

Explanation of Solution

Want to see more full solutions like this?

Chapter 21 Solutions

Additional Engineering Textbook Solutions