![Mechanics of Materials, 7th Edition](https://www.bartleby.com/isbn_cover_images/9780073398235/9780073398235_largeCoverImage.gif)
A 250-mm-long aluminum tube (E = 70 GPa) of 36-mm outer diameter and 28-mm inner diameter can be closed at both ends by means of single-threaded screw-on covers of 1.5-mm pitch. With one cover screwed on tight, a solid brass rod (E = 105 GPa) of 25-mm diameter is placed inside the tube and the second cover is screwed on. Since the rod is slightly longer than the tube, it is observed that the cover must be forced against the rod by rotating it one-quarter of a turn before it can be tightly closed. Determine (a) the average normal stress in the tube and in the rod, (b) the deformations of the tube and of the rod.
Fig. P2.16
a)
![Check Mark](/static/check-mark.png)
The average normal stress in the tube
Answer to Problem 16P
The average normal stress in the tube
Explanation of Solution
Given information:
The length of the tube (L) is
The outer diameter of the tube
The inner diameter of the tube
The Young’s modulus of the aluminium
The diameter of the rod
The Young’s modulus of the brass
The pitch of the single-threaded screw-on cover (p) is
The load act in the tube is P.
Calculation:
Calculate the cross sectional area of the tube
Substitute
Calculate the cross sectional area of the rod
Substitute
Calculate the deformation of the tube
Substitute
Calculate the deformation of the rod
Substitute
Calculate the deformation of the screw
Substitute
Calculate the load (P) act in the tube using the formula:
Substitute
Calculate the average normal stress in the tube
Substitute
Calculate the average normal stress in the rod
Substitute
Hence, the average normal stress in the tube
b)
![Check Mark](/static/check-mark.png)
The deformations of the tube
Answer to Problem 16P
The deformations of the tube
Explanation of Solution
Given information:
The length of the tube (L) is
The outer diameter of the tube
The inner diameter of the tube
The Young’s modulus of the aluminium
The diameter of the rod
The Young’s modulus of the brass
The pitch of the single-threaded screw-on cover (p) is
The load act in the tube is P.
Calculation:
Calculate the cross sectional area of the tube
Substitute
Calculate the cross sectional area of the rod
Substitute
Calculate the deformation of the tube
Substitute
Calculate the deformation of the rod
Substitute
Calculate the deformation of the screw
Substitute
Calculate the load (P) act in the tube using the formula:
Substitute
Calculate the deformations of the tube
Substitute
Calculate the deformations of the rod
Substitute
Hence, the deformations of the tube
Want to see more full solutions like this?
Chapter 2 Solutions
Mechanics of Materials, 7th Edition
- Please Solve this ASAParrow_forwardSolve fast and correctly pleasearrow_forwardThe rectangular bar shown is connected to a support bracket with a 24 mm diameter pin. The width of the rectangular bar is 70 mm and its thickness is 15 mm. The bearing stress in the bar cannot exceed 120 MPa. Determine the maximum value of Pmax that can be supported based solely on consideration of the bearing stress in the bar. Note: This question is not asking about any stresses in the support bracket...just bearing stress in the rectangular bar.arrow_forward
- A double riveted butt joint, in which the pitch of the rivets in the outer rows is twice that in the inner Rows, connects two 16mm thick plates with two cover plates each 12 mm thick. The diameter of rivets is 22 mm. Determine the pitches of the rivets in the two rows if the working stresses are not to exceed the following limits: Tensile stress in plates =100 MPa; Shear stress in rivets =75 MPa; and bearing stress in rivets and plates =150 MPa. Make a fully dimensioned sketch of the joint by showing at least two views.arrow_forwardA 20 mm diameter steel rod passes concentrically through a bronze tube (200+SN) mm long, 50 mm external diameter and 40 mm internal diameter. The ends of the steel rod are threaded and provided with nuts and washers which are adjusted initially so that there is no end play at 25°C.. 1. Assuming that there is no change in the thickness of the washers, if the stress produced in the steel is (200+SN) MN/m2 when one of the nuts is tightened, the pitch of the thread being 1 mm. Find the number of turns for the nut and stress in bronze tube.2. If the temperature of the steel and bronze is then raised to 4O°C find the changes that will occur in the stresses in both materials. The coefficient of linear expansion per C is 10 x10-6 for steel and 17 x10-6 for bronze. E for steel = 210 GN/m2. E %3D for bronze = 100 GN/m2.. Note: SN = %3D Student number Student Number =32arrow_forwardPROBLEM 3. A double-row butt joint is used as a connection. It is made up of two 210-mm by 20-mm cover plates and 210-mm by 35-mm main plate. The plates are to be connected by 32-mm diameter rivets. The allowable stresses are 75MPa for shear, 90MPa for tension and 285MPa bearing. Assume that each hole is 3mm larger than the rivet diameter. ust PDF ng imen GIBL o Alel 1. What is the largest value of P (kN) that can be applied without exceeding the ollowable stress for shear? 2. What is the largest value of P (kN) that can be applied without exceeding the ollowable stress for bearing? 3. What is the largest value of P (kN) that can be applied withour exceeding the allowable stress for tension? ng inarrow_forward
- Compute for (a) the force exerted on the bolt and rivets at joints A, B, and C and (b) the normal stress in member AD, if a force P of magnitude 300 N is applied to the handles of the bolt cutter shown in figure below, from which it has a uniform cross-sectional area of 2x10-4 m22x10-4 m². 300 N 24 mm D 12 mm B E 96 mm 24 mm 24 mm 460 mm- 300 Narrow_forwardPlease solve the problem correctly and submit within 30min. I have attached the translation of the question.arrow_forwardQuickly pleasearrow_forward
- B2arrow_forwardA circular steel bar 50 mm diameter and 200 mm long is welded perpendicularly to a steel plate to form a cantilever to be loaded with 5 kN at the free end. Determine the size of the weld, assuming the allowable stress in the weld as 100MPa.arrow_forwardAxial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal stress in aluminum rod (1) must be limited to 19 ksi, the normal stress in brass rod (2) must be limited to 23 ksi, and the normal stress in steel rod (3) must be limited to 12 ksi. Determine the minimum diameter required for each of the three rods. Assume P = 8 kips, Q = 6 kips, R = 20 kips and S = 21 kips. A D First: Calculate the internal force (positive if tensile, negative if compresive) in rod (1). Use a FBD cutting through the rod in the section that includes the free end A. Answer: F₁ = i kips. (2) (3) O B Carrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
![Text book image](https://www.bartleby.com/isbn_cover_images/9780190698614/9780190698614_smallCoverImage.gif)
![Text book image](https://www.bartleby.com/isbn_cover_images/9780134319650/9780134319650_smallCoverImage.gif)
![Text book image](https://www.bartleby.com/isbn_cover_images/9781259822674/9781259822674_smallCoverImage.gif)
![Text book image](https://www.bartleby.com/isbn_cover_images/9781118170519/9781118170519_smallCoverImage.gif)
![Text book image](https://www.bartleby.com/isbn_cover_images/9781337093347/9781337093347_smallCoverImage.gif)
![Text book image](https://www.bartleby.com/isbn_cover_images/9781118807330/9781118807330_smallCoverImage.gif)