Concept explainers
A 4-lb uniform rod is supported by a pin at O and a spring at A and is connected to a dashpot at B. Determine (a) the differential equation of motion for small oscillations, (b) the angle that the rod will form with the horizontal 5 s after end B has been pushed 0.9 in. down and released.
Fig. P19.165
(a)
The differential equation of motion for small oscillations.
Answer to Problem 19.165RP
The differential equation of motion for small oscillations is
Explanation of Solution
Given information:
The weight of the uniform rod (W) is 4 lb.
The distance between A to O (a) is 6 inch.
The distance between O to B (b) is 18 in.
The spring constant (k) is 5 lb/ft.
The damping coefficient (c) is
The acceleration due to gravity (g) is
Calculation:
Calculate the mass of the uniform rod (m) using the formula:
Substitute 4 lb for W and
Show the free body diagram of the rod as Figure (1).
For small angle, take
Calculate the deflection at the point A
Substitute 6 in. for a.
Calculate the deflection at the point B
Substitute 18 in. for b.
Calculate the deflection at the point C
Substitute 6 in. for a.
Take the moment about O.
Calculate for the spring force
Substitute
Calculate the damping force
Substitute
Calculate the moment of inertia
Substitute 6 in. for a and 18 in. for b.
The angle
Calculate the acceleration
Substitute 6 in. for a and
Substitute
Consider equilibrium.
Take the moment about O.
Substitute 2 for
Substitute
Therefore, the differential equation of motion for small oscillations is
(b)
The angle that the rod
Answer to Problem 19.165RP
The angle that the rod
Explanation of Solution
Given information:
The weight of the uniform rod (W) is 4 lb.
The distance between A to O (a) is 6 inch.
The distance between O to B (b) is 18 inch.
The spring constant (k) is 5 lb/ft.
The damping coefficient (c) is
The acceleration due to gravity (g) is
Calculation:
Consider the equation (3).
Substitute
Solve the above equation.
Since the computed roots are real and distinct.
Write the expression for the general solution for the differential equation as follows:
Substitute 0 for t.
Differentiate the equation (4) with respect to time ‘t’.
Substitute 0 for t.
The above solution corresponds to a no vibratory motion because the roots
Therefore, the angle that the rod
Want to see more full solutions like this?
Chapter 19 Solutions
VECTOR MECH...,STAT.+DYNA.(LL)-W/ACCESS
- The primary material used in the production of glass products is silica sand. True or Falsearrow_forwardWhich one of the following is the most common polymer type in fiber-reinforced polymer composites? thermosets thermoplastics elastomers none of the abovearrow_forwardA pattern for a product is larger than the actual finished part. True or Falsearrow_forward
- Two forces are applied as shown to a hook support. The magnitude of P is 38 N. 50 N 25° DG a 터 Using trigonometry, determine the required angle a such that the resultant R of the two forces applied to the support will be horizontal. The value of a isarrow_forwardNo chatgpt pls will upvotearrow_forward101 the three shafts if the diameter ratio is 2 (D/d = 2)? Ans. na, tension = 1.21, na, bending = 1.19, na, torsion = 1.17. 6.32 A material with a yield strength of S₁ = 350 MPa is subjected to the stress state shown in Sketch c. What is the factor of safety based on the maximum shear stress and distortion energy theories? Ans. For MSST, n, = 11.67. 50 MPa 85 MPa 20 MPa 70 MPa Sketch c, for Problems 6.32 and 6.33arrow_forward
- Can you draw the left view of the first orthographic projectionarrow_forwardImportant: I've posted this question twice and received incorrect answers. I've clearly stated that I don't require AI-generated working out. I need a genuine, expert-written solution with proper working. If you can't provide that, refer this question to someone who can please!. Note: Please provide a clear, step-by-step handwritten solution (no AI involvement). I require an expert-level answer and will assess it based on quality and accuracy with that I'll give it a thumbs up or down!. Hence, refer to the provided image for clarity. Double-check everything for correctness before submitting. Thank you!arrow_forwardNote: Please provide a clear, step-by-step simplified handwritten working out (no explanations!), ensuring it is done without any AI involvement. I require an expert-level answer, and I will assess and rate based on the quality and accuracy of your work and refer to the provided image for more clarity. Make sure to double-check everything for correctness before submitting appreciate your time and effort!. Question:arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY