(a) Explanation Given Information: The mass ( m ) of the block is 12 kg. The spring constant ( k ) is 5 kN/m . Calculation: The static elongation of the spring ( δ s t ) is equal to amplitude ( x m ) is 0.2222 in . . Calculate the natural circular frequency ( ω n ) using the relation: ω n = k m Substitute 5 kN/m for k and 12 kg for m . ω n = ( 5 kN/m × 1000 N 1 kN ) 12 = 416.667 = 20.412 rad/s Calculate the period ( τ n ) using the relation: τ n = 2 π ω n Substitute 20 (b) To determine The maximum velocity ( v m ) and maximum acceleration ( a m ) of the block.

11th Edition

ISBN: 9781259633133

Author: BEER

Publisher: MCG

See similar textbooks

Question

Chapter 19.1, Problem 19.5P

(a)

To determine

The period (τn) and frequency (fn) of the resulting motion.

(b)

To determine

The maximum velocity (vm) and maximum acceleration (am) of the block.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 19.1, Problem 19.4P

Chapter 19.1, Problem 19.6P

Students have asked these similar questions

The gears shown in the figure have a diametral pitch of 2 teeth per inch and a 20° pressure angle. The pinion rotates at 1800 rev/min clockwise and transmits 200 hp through the idler pair to gear 5 on shaft c. What forces do gears 3 and 4 transmit to the idler shaft? TS I y 18T 32T This a 12 x 18T C 48T 5

Question 1. Draw 3 teeth for the following pinion and gear respectively. The teeth should be drawn near the pressure line so that the teeth from the pinion should mesh those of the gear. Drawing scale (1:1). Either a precise hand drawing or CAD drawing is acceptable. Draw all the trajectories of the involute lines and the circles. Specification: 18tooth pinion and 30tooth gear. Diameter pitch=P=6 teeth /inch. Pressure angle:20°, 1/P for addendum (a) and 1.25/P for dedendum (b). For fillet, c=b-a.

5. The figure shows a gear train. There is no friction at the bearings except for the gear tooth forces. The material of the milled gears is steel having a Brinell hardness of 170. The input shaft speed (n2) is 800 rpm. The face width and the contact angle for all gears are 1 in and 20° respectively. In this gear set, the endurance limit (Se) is 15 kpsi and nd (design factor) is 2. (a) Find the revolution speed of gear 5. (b) Determine whether each gear satisfies the design factor of 2.0 for bending fatigue. (c) Determine whether each gear satisfies the design factor of 2.0 for surface fatigue (contact stress). (d) According to the computation results of the questions (b) and (c), explain the possible failure mechanisms for each gear. N4=28 800rpm N₁=43 N5=34 N₂=14 P(diameteral pitch)=8 for all gears Coupled to 2.5hp motor

Chapter 19 Solutions

VECTOR MECH...,STAT.+DYNA.(LL)-W/ACCESS

Ch. 19.1 - A particle moves in simple harmonic motion....Ch. 19.1 - Prob. 19.2P Ch. 19.1 - Prob. 19.3P Ch. 19.1 - Prob. 19.4P Ch. 19.1 - Prob. 19.5P Ch. 19.1 - Prob. 19.6P Ch. 19.1 - Prob. 19.7P Ch. 19.1 - Prob. 19.8P Ch. 19.1 - Prob. 19.9P Ch. 19.1 - Prob. 19.10P

Knowledge Booster

The period ( τ n ) and frequency ( f n ) of the resulting motion.

The period (τn) and frequency (fn) of the resulting motion.

The maximum velocity (vm) and maximum acceleration (am) of the block.

Want to see the full answer?

Chapter 19 Solutions