Engineering Mechanics: Dynamics (14th Edition)
14th Edition
ISBN: 9780133915389
Author: Russell C. Hibbeler
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 18.5, Problem 7RP
If the disk rolls without slipping, determine the velocity of the collar at the instant the rod becomes horizontal, i.e., θ = 0°. The system is released from rest when θ = 45°.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
The system consists of a 19-lb disk A, a 4-lb slender rod BC, and a 3-lb smooth collar C. If the disk rolls without slipping, determine the velocity of the collar at the instant θ = 20°. The system is released from rest when θ = 48°.
The slotted arm OB rotates in a horizontal plane about point O of the fixed circular cam with constant angular velocity 0 = 10rad/s.
The spring has a stiffness of 6.4 kN/m and is uncompressed when 80. The smooth roller A has a mass of 0.36 kg. Determine the
normal force N which the cam exerts on A and also the force R exerted on A by the sides of the slot when 8 52°. The force R is positive
if contact is with the lower surface. All surfaces are smooth. Neglect the small diameter of the roller.
Answers:
N=
R=
0.19
m
0.19
m
B
278.166820949951087 N
N
The particle of mass m = 2.1 kg is attached to the light rigid rod of length L = 0.91 m, and the assembly rotates about a horizontal axis through O with a constant angular velocity θ˙θ˙ = ω = 2.9 rad/s. Determine the force T in the rod when θ = 28°. The force T is positive if in tension, negative if in compression.
Determine the force T in the rod when θ = 28°. The force T is positive if in tension, negative if in compression.
Chapter 18 Solutions
Engineering Mechanics: Dynamics (14th Edition)
Ch. 18.4 - Determine the kinetic energy of the 100-kg object.Ch. 18.4 - The 80-kg wheel has a radius of gyration about its...Ch. 18.4 - If the rod is at rest when = 0, determine its...Ch. 18.4 - Determine the angular velocity of the rod when the...Ch. 18.4 - If the wheel starts from rest and rolls Without...Ch. 18.4 - If the uniform 30-kg slender rod starts from rest...Ch. 18.4 - When it is subjected to a couple moment of M = 50...Ch. 18.4 - Show that its kinetic energy can be represented a...Ch. 18.4 - If the torsional spring attached to the wheel's...Ch. 18.4 - If the torsional spring attached to the wheel's...
Ch. 18.4 - Determine the angular velocity of the reel after...Ch. 18.4 - Determine the angular velocity of the reel after...Ch. 18.4 - Determine the angular velocity of the reel after...Ch. 18.4 - It has a weight of 50 lb and a centroidal radius...Ch. 18.4 - It has a weight of 50 lb and a centro1dal radius...Ch. 18.4 - If it starts from rest, determine its angular...Ch. 18.4 - If the 10-kg block is released from rest,...Ch. 18.4 - Determine the angular velocity of the 20-kg wheel...Ch. 18.4 - Initially, the system is at rest. The reel has a...Ch. 18.4 - The force is always perpendicular to the rod.Ch. 18.4 - Determine the angular velocity of the rod when it...Ch. 18.4 - If it is released from rest in the position shown,...Ch. 18.4 - If the elevator has a mass of 900 kg, the...Ch. 18.4 - If the ring rolls without slipping, determine its...Ch. 18.4 - A motor supplies a torque M = (40 + 900) Nm ,...Ch. 18.4 - When empty it has a mass of 800 kg and a radius of...Ch. 18.4 - If P = 200 N and the 15-kg uniform slender rod...Ch. 18.4 - If it is released from rest, determine how far it...Ch. 18.4 - The windlass A can be considered as a 30-lb...Ch. 18.4 - If the conveyor belt is moving with a speed of Vc...Ch. 18.4 - A couple moment of M = 80 Nm is then applied to...Ch. 18.4 - A couple moment M = 80 Nm is then applied to the...Ch. 18.4 - If the plate is released from rest at = 90,...Ch. 18.4 - If the ring gear C is fixed, determine the angular...Ch. 18.4 - If the rod is released from rest when the spring...Ch. 18.4 - Determine the speed of the sptere's center of mass...Ch. 18.4 - Motor M exerts a constant force of P = 750 Non the...Ch. 18.4 - When = 0, rod AB is rotating with an angular...Ch. 18.4 - If rod CD is subjected to a couple moment M = 30...Ch. 18.4 - The gears roll within the fixed ring gear C, which...Ch. 18.4 - When = 0, rod AB is rotating with an angular...Ch. 18.4 - When = 0, rod AB is rotating with an angular...Ch. 18.5 - If the 30-kg disk is released from rest when = 0...Ch. 18.5 - If it is released from rest, determine its angular...Ch. 18.5 - Determine its angular velocity when = 45.The...Ch. 18.5 - Determine the angular velocity of the rod when =...Ch. 18.5 - Determine the angular velocity of the rod when =...Ch. 18.5 - Determine its angular velocity when = 90. The...Ch. 18.5 - If a 2-kg block is suspended from the cord,...Ch. 18.5 - Prob. 37PCh. 18.5 - If it is released from rest at A on the incline,...Ch. 18.5 - The spool has a mass of 20 kg and a radius of...Ch. 18.5 - If the 15-kg block A is released from rest,...Ch. 18.5 - If it is allowed to fall freely determine the...Ch. 18.5 - Gear A has a mass of 10kg and a radius of gyration...Ch. 18.5 - If the rod is released from rest when = 30,...Ch. 18.5 - If the rod is released from rest when = 30,...Ch. 18.5 - The 40-kg wheel has a radius of gyration about its...Ch. 18.5 - If the bars are released from rest when = 60,...Ch. 18.5 - If the bars are released from rest when = 60,...Ch. 18.5 - If it has a mass of 3 kg and a rad1us of gyration...Ch. 18.5 - Lifting is done using the two springs, each of...Ch. 18.5 - If the spring has an unstretched length of 1.5 m,...Ch. 18.5 - If the spring has an unstretched length of 1.5 m,...Ch. 18.5 - The drum has a weight of 50 lb and a radius of...Ch. 18.5 - If the track in which it moves is smooth,...Ch. 18.5 - The pulley has a weight of 50 lb and a rad1us of...Ch. 18.5 - The gear has a weight of 100 lb and a radius of...Ch. 18.5 - Determine the stiffness k of the spring so that...Ch. 18.5 - The slender 6-kg bar AB is horizontal and at rest...Ch. 18.5 - If the spring has an unstretched length of 0.2 m,...Ch. 18.5 - The 500-g rod AB rests along the smooth inner...Ch. 18.5 - The 50-lb wheel has a radius of gyration about its...Ch. 18.5 - The system consists of 60-lb and 20-lb blocks A...Ch. 18.5 - The door is made from one piece, whose ends move...Ch. 18.5 - The door is made from one piece, whose ends move...Ch. 18.5 - The end A of the garage door AB travels along the...Ch. 18.5 - The system consists of a 30-kg disk, 12-kg slender...Ch. 18.5 - The system consists of a 30-kg disk A, 12-kg...Ch. 18.5 - If it is released from rest when = 0, determine...Ch. 18.5 - If it is subjected to a torque of M = (91/2+ 1)...Ch. 18.5 - Starting from rest, the suspended 15-kg block B is...Ch. 18.5 - If it is released from rest, determine how far its...Ch. 18.5 - If the rack is originally moving downward at 2...Ch. 18.5 - The spring attached to its end always remains...Ch. 18.5 - If the disk rolls without slipping, determine the...Ch. 18.5 - At the instant the spring becomes undeformed, the...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- In the figure, rod AB has a mass of 10 kg, and must slide within the slots as shown. If the spring is unstretched when θ = 0°, determine the angular velocity of the bar when it reaches that angle after being released from θ = 30°.arrow_forward1. If the cord is subjected to a horizontal force of P = 150N, and gear is supported by a fixed pin at O, determine the angular velocity of the gear and the velocity of the 20-kg gear rack in 4 s, starting from rest. The mass of the gear is 50-kg and it has a radius of gyration of ko = 125 mm. Assume that the contact surface between the gear rack and the horizontal plane is smooth. 75 mm P = 150 N 150 mmarrow_forwardThe spring-held follower AB has a mass of 0.5 kg and moves back andforth as its end rolls on the contoured surface of the cam, where r = 0.15 m and z =(0.02 cos 2θ) m. If the cam is rotating at a constant rate of 30 rad/s, determine theforce component Fz at the end A of the follower when θ = 30°. The spring isuncompressed when θ = 90°. Neglect friction at the bearing C.arrow_forward
- The collar has a mass of 2 kg and is attached to the light spring, which has a stiffness of 30 N∕m and an unstretched length of 1.5 m. The collar is released from rest at A and slides up the smooth rod under the action of the constant 50-N force. Calculate the velocity v of the collar as it passes position B. Use a datum coinciding with B such that y axis is positive to the right and z axis is positive down.arrow_forward1. The two blocks A and B each have a mass of 470 g. The blocks are fixed to the horizontal rods, and their initial velocity along the circular path is 2 m/s. The spheres are also subjected to tangential forces of P= 10 N. A couple moment of M= (f+2) N.m is applied about CD of the frame. The mass of the frame is negligible, and it is free to rotate about CD. Neglect the size of the blocks. Determine the speed of the blocks when t = 5 s. C M = ( + 2) N · m A В P = 10 N P = 10 N 0.3 m- 0.3 m. Darrow_forwardThe 10-kg rod AB shown is confined so that its ends move in the horizontal andvertical slots. The spring has a stiffness of k = 800N/m and is unstretched when θ = 0˚.Determine the angular velocity of AB when θ = 0˚, if the rod is released from rest when θ = 30˚.Neglect the mass of the slider blocks. It’s frictionless.arrow_forward
- If the cord is subjected to a horizontal force of P = 150 N, and gear is supported by a fixed pin at O,determine the angular velocity of the gear and the velocity of the 20-kg gear rack in 4 s, starting from rest. The mass of the gear is 50 kg and it has a radius of gyration of k0 = 125 mm. Assume that the contact surface between the gear rack and the horizontal plane is smooth.arrow_forwardThe 1.2-kg uniform slender bar rotates freely about a horizontal axis through O. The system is released from rest when it is in the horizontal position 0 = 0 where the spring is unstretched. If the bar is observed to momentarily stop in the position 0 = 50° determine the spring constant k. For your computed value of k, what is the angular velocity of the bar when 0 = 35°? 0.6 m 0.6 m 1.2 kg 0.2 m wwwarrow_forwardAt the instant shown, the spring is undeformed. Determine the change in potential energy if the 20 kg disk (kG = 0.5 m) rolls 2 revolutions without slipping. ½(200)(1.2 π )2 + (20) (9.81) (1.2 π sin 30°) - ½(200)(1.2 π )2 - (20) (9.81) (1.2 π sin 30°) ½(200)(1.2 π )2 - (20) (9.81) (1.2 π sin 30°) ½(200)(1.2 π )2arrow_forward
- Rod OA rotates counterclockwise at a constant angular rate 0 = 4 rad/s. The double collar Bis pin-connected together such that Determine the magnitude of the force which the circular rod exerts on one of the collars at the instant 0 = 45°. one collar slides over the rotating rod and the other collar slides over the circular rod described by the equation r = (1.6 cos 0) m Both collars have a mass of 0.65 kg. Motion is in the vertical plane. (Figure 1) Express your answer to three significant figures and include the appropriate units. HA ? F = - 11.766 Figure 1 of 1 Submit Previous Answers Request Answer X Incorrect; Try Again; 3 attempts remaining r = 1.6 cos 0 0 = 4 rad/s B Part B Determine the magnitude of the force that OA exerts on the other collar at the instant 0 = 45°. Express your answer to three significant figures and include the appropriate units. 0.8 m HẢ ? FOA = 11.766arrow_forwardBy using a forked rod, a smooth cylinder C having a mass of 0.5 kg is forced to move along the vertical slotted path (r = 0.4 θ) m, where θ is in radians. If the angular position of the arm is θ = (0.3 t3 ) rad, where t is in seconds. The cylinder is in contact with only one edge of the rod and slot at any instant. Find "the force of the rod on the cylinder at the instant t=2s" Find "the normal force of the slot at the instant t=2s" Find the "radius of curvature at t=2s" Find the "ψ angle at t=2s"arrow_forwardThe four balls, each of mass m = 2.3 kg, are rigidly mounted to the rotating frame and shaft, which are initially rotating freely about the vertical z-axis at the angular rate of 19.5 rad/s clockwise when viewed from above. The distances r = 0.25 m and R = 0.52 m. If a constant torque M = 23.1 N·m is applied to the shaft, calculate the time t to reverse the direction of rotation and reach an angular velocity = 19.5 rad/s in the same sense as M. m R m r M m R marrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Mechanical SPRING DESIGN Strategy and Restrictions in Under 15 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=dsWQrzfQt3s;License: Standard Youtube License