Explanation Drawing can be defined as the method in which metal or material is dragged through the die that leads to a decrease in thickness. This process is very much similar to the process of extrusion, but the major difference is the use of exerted force. Extrusion is the process in which material is forces to pass through die, so that the change in the shape of the material can take place. This process is used to create a product that has a fixed cross-sectional profile. The comparison between the conventional extrusion, wire drawing, and continuous extrusion is shown below using tabular form. Process Possible materials Reduction in area Typical temperature Process parameters Speeds Conventional extrusion Aluminum, Magnesium, Lead alloys. 10 % to 40 % At most annealed temperatures 300 m / min

Degarmo's Materials And Processes In Manufacturing

13th Edition

ISBN: 9781119492825

Author: Black, J. Temple, Kohser, Ronald A., Author.

Publisher: Wiley,

See similar textbooks

Concept explainers

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the s…

Videos

Question

Chapter 18, Problem 6P

To determine

The comparison on several processes.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 18, Problem 5P

Chapter 18, Problem 7P

Students have asked these similar questions

A turbocharged engine with a compression ratio of 8 is being designed using an air standard cycle. The ambient air is assumed to be 300K and 100 kPa. The temperature at the end of the compression in the cylinder is desired to be 1000K, assuming no combustion prior to reaching TDC. At the end of the cylinder expansion the temperature is also desired to be 1000K. If both the turbine and the compressor have mechanical efficiencies of 80%, what will be the pressure ratio of the compressor and what will be the turbine exhaust temperature?

Q6: A turbocharged engine with a compression ratio of 8 is being designed using an air standard cycle. The ambient air is assumed to be 300K and 100 kPa. The temperature at the end of the compression in the cylinder is desired to be 1000K, assuming no combustion prior to reaching TDC. At the end of the cylinder expansion the temperature is also desired to be 1000K. If both the turbine and the compressor have mechanical efficiencies of 80%, what will be the pressure ratio of the compressor and what will be the turbine exhaust temperature?

Q5: A 5.6 litre V8 engine with a compression ratio of 9.4:1 operates on an air-standard Otto cycle at 2800 RPM, with a volumetric efficiency of 90 % and a stoichiometric air-fuel ratio using gasoline. The exhaust flow undergoes a temperature drop of 44ºC as it passes through the turbine of the supercharger. Calculate (a) mass flow rate of exhaust gas and (b) power available to drive the turbocharger compressor.

Chapter 18 Solutions

Degarmo's Materials And Processes In Manufacturing

Ch. 18 - Briefly describe the evolution of forming...Ch. 18 - What are some of the possible means of classifying...Ch. 18 - How are bulk deformation processes different from...Ch. 18 - Prob. 4RQ Ch. 18 - Prob. 5RQ Ch. 18 - Prob. 6RQ Ch. 18 - Prob. 7RQ Ch. 18 - Why is it undesirable to minimize friction between...Ch. 18 - Prob. 9RQ Ch. 18 - Prob. 10RQ

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

The comparison on several processes.

Solution Summary: The author explains the differences between drawing and extrusion, and compares them using tabular form.

Concept explainers

Videos

The comparison on several processes.

Want to see the full answer?

Chapter 18 Solutions