An old fashioned ice cream kit consists of two concentric cylinders of radii Ra and Rb. The inner cylinder is filled with milk and ice cream ingredients while the space between the two cylinders is filled with an ice-brine mixture. Ice cream begins to form on the inner surface of the inner cylinder. To expedite the process, would you recommend rotating the inner cylinder? Justify your recommendation. icecream/ ice-brine Ra Rb

An old fashioned ice cream kit consists of two concentric cylinders of radii Ra and Rb. The inner cylinder is filled with milk and ice cream ingredients while the space between the two cylinders is filled with an ice-brine mixture. Ice cream begins to form on the inner surface of the inner cylinder. To expedite the process, would you recommend rotating the inner cylinder? Justify your recommendation. icecream/ ice-brine Ra Rb

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter28: Special Refrigeration Applications

Section: Chapter Questions

Problem 1RQ: List the evaporating temperatures for liquid nitrogen and CO2: _____and____.

See similar textbooks

Similar questions

A process equipment contains 100 gallons of water at 25C. It isrequired to bring it to boiling in 10 minutes. The heat loss is estimated tobe 5%.What is the kilowatt rating of the heater? the answer is 207kW (According to ECE board exam answer key) I can't solve it, Can you show me your solution?
Explain what a "heated zone" is, how it operates, and any potential restrictions.
Solve the attachment
Using the answers from questions 14, 15, and 16, whatwould be the total heat gain due to the fresh air for thehouse in question 13? [13. A house has 3500 ft2 of floor space and a 9-ft ceiling.What is the cubic volume of the house?14. If the fresh-air requirements for the house in question 13were to be 0.4 air changes per hour, how much fresh airmust be taken in per minute?15. If the outside fresh-air conditions were to be 93°F drybulband 74°F wet-bulb, what would the total heat contentof the air be?16. If the air leaving the cooling coil were to be 55°F drybulband 53°F wet-bulb, what would the total heat contentof the air be?]
Describe what a "heated zone" is, how it works, and any limitations that may apply to it.
One of the ways to keep a pipe warm is by means of a steam tracer, through which an electrical resistance is used around the pipe and in a helical shape throughout its diameter?
Show your commplete solution.
A sprue is 250 mm long. The velocity of the molten metal at the top of the sprue is 0.15 m/s. The middle diameter of the sprue is 10 mm. The total cavity of the "runner system + mold" is 2.5 × 106 mm³. The viscosity of the molten metal is 0.0022 kg/(m · s) and the density is 2700 kg/m³. According to given information i. For a proper sprue design, calculate the bottom diameter of the sprue ii. Find the velocity at the bottom of the sprue iii. Find the volumetric and mass flow rates at the bottom of the sprue iv. Find the required time to fill the mold completely v. Is the flow laminar, mixed or turbulent at the bottom of the sprue? P v? pg' 2g h+-+; = constant Q = A,V1 = A2V2 h2 h1 pVD Re A1 TST = Cm G) A2
Thermal properties of mould and Iron is given as latent heat of iron = 270 the freezing temperature of iron = 1500 C. the density of molten iron = 7500 kg kJ kg-K the specific heat of mould material = 1.2 the themal condudivity of mould material = 09 Wm-K the density of the mould material = 1500 kg Determine the solidification time for a slab-shaped casting of 16 e thickness when iỘn withaut superheat is poured into the sand mold at an initial m temperature of 300 C BI U
Water is to be boiled at atmospheric pressure in a polished copper pan placed on top of a heating unit. The diameter of the bottom of the pan is 00.2 m. If during 30 minutes the water level is dropped by 0.1 m, calculate the inner surface of the bottom of the pan. Assumptions 1 Steady operating conditions exist. 2 Heat losses from the heater and the pan are negligible 3 The boiling regime is nucleate boiling. Note. Write your answer step by step and clearly explain your work. You need to upload a file.
Given that Wm= weight of the molten metal displaced by a core and Wc = weight of the core, the buoyancy force is which one of the following downward force = Wm + Wc downward force = Wm - Wc + CO upward force = Wm + Wc upward force = Wm - Wc O buoyancy force = Wm - Wc O
Question 3 Which statement about vaporization enthalpy and condensation enthalpy is correct? O The condensation enthalpy is equal in magnitude but opposite in sign when compared to the vaporization enthalpy O There is no general relationship between these two quantities and the values depend on the substance involved. O The vaporization enthalpy is always less than the condensation enthalpy. O The vaporization enthalpy is exactly equal to the condensation enthalpy.