Water is to be boiled at atmospheric pressure in a polished copper pan placed on top of a heating unit. The diameter of the bottom of the pan is 0.2 m. If during 30 minutes the water level is dropped by 0.1 m, calculate the inner surface of the bottom of the pan. Assumptions 1 Steady operating conditions exist. 2 Heat losses from the heater and the pan are negligible 3 The boiling regime is nucleate boiling. Note. Write your answer step by step and clearly explain your work. You need to upload a file.

Water is to be boiled at atmospheric pressure in a polished copper pan placed on top of a heating unit. The diameter of the bottom of the pan is 0.2 m. If during 30 minutes the water level is dropped by 0.1 m, calculate the inner surface of the bottom of the pan. Assumptions 1 Steady operating conditions exist. 2 Heat losses from the heater and the pan are negligible 3 The boiling regime is nucleate boiling. Note. Write your answer step by step and clearly explain your work. You need to upload a file.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

DESCRIBE THE INTERNAL ENERGY, ENTHALPY, AND SPECIFIC HEATS OF SOLIDS AND LIQUIDS
@ Draw a neat sketch for a seive tray column for gas-liquid contact. Label the main parts of such column? And what are other types of trays?
All properties should be evaluated at the temperature of the steam.Saturated, pure steam at 65 ºC condenses on the surface of a vertical tube with outersurface diameter 2 cm which is maintained at a uniform temperature of 35 ºC. Determinethe tube length for a condensate flow rate of 5 x 10-3 kg/s.
The evaporation pan coefficient of * class A pan is generally taken as
Saturated, pure steam at a temperature of 170 oC condenses on the outer surface of a vertical tube of outer diameter 2 cm and length 1.5 m. The tube surface is maintained at a uniform temperature of 150 oC. Calculate: the local film condensation heat-transfer coefficient at the bottom of the tube. the average condensation heat-transfer coefficient over the entire length of the tube. the total condensation rate at the tube surface.
It has been found that condensation forms on the outside of the refrigerator when the temperature on the surface is T1 and lower certain parts during the year. If the temperature on the inside of the refrigerator is T2 , how thick insulation needed to avoid condensation? The cooling effect in the refrigerator is ?. The refrigerator wall is built (from the outside) with 1 mm metal (thermal conductivity is k1),mineral wool (thermal conductivity is k2)and an additional layer of 1 mm metal. T1 (°C)= 15 , T2(°C)=3 , ? (W)=70 , k1 (W/m·K)=15 , k2 (W/m·K)=0.04
Saturated, pure steam at a temperature of 170 oC condenses on the outer surface of avertical tube of outer diameter 2 cm and length 1.5 m. The tube surface is maintained at auniform temperature of 150 oC.Calculate:a) the local film condensation heat-transfer coefficient at the bottom of the tube. b) the average condensation heat-transfer coefficient over the entire length of the tube. c) the total condensation rate at the tube surface.
Pre-lab 8: Cold Engine The experimental setup for this week's lab consists of a syringe connected to a metal can (reservoir), a cold bath (water - ice mixture) and a "hot" bath (water at room temperature). A schematics of the syringe - reservoir system is shown below. Plunger of mass m Filled with gas (air) Syringe of volume Vcor VH - Volume Vo includes tube + Metal can -Metal can submerged in water of temperature Тс or TH. Tube Stopper Figure 1: Schematic of the syringe - reservoir system. The syringe is essentially a glass cylinder fitted with a movable piston (plunger). The markings on the syringe indicate the volume of gas in the syringe, but do not include the additional, unknown volume, Vo, in the gas can and tubing.
Which mode or condensation is characterized by larger heat transfer rates?
Use the Kedzierski (2003) refrigerant/lubricant mixture pool boiling model to predict the boiling heat transfer coefficient (hm) for a range of superheats (4T, = 8 K to 40 K) and Ts = 277.6 K: 5.9×107(1−x,)ph ATk, (1-e*) x, To Where 1₂ %₁ = = 9m T-T Г x Τσ PL-Pbx 5.9×107(1-x₂)ph AT 0.755lp₁ (1-x₁) _ 18.75Ãµ₁ (1—x₁) _ 18.75×10¯¹º[m]p, (1-x₂) Xp Prv XpPrv XpPrv Assume that λ = 1.34 for xb=0.005 and that λ = 0.3 for Xb = 0.02. The properties of the refrigerant (R123) at the film temperature are: KL (W/mK) 0.139 R123 Or (N/m) 179692.3 0.01764 hfg (J/kg) The properties of the mineral oil (lubricant) are: PL (kg/m³) 917.8 York-C VL (cSt) 60 Prv (kg/m³) 2.701 VL (m²/s) 6 × 10-5 OL (N/m) 0.026 1.) Plot hm vs ATs and le vs ATs for two lubricant mass fractions: x = 0.005 (use 2 = 1.34 for Xb = = 0.005) and x = 0.02 (use λ = 0.3 for xb = 0.02). Compare the predicted ro for the two mass fraction cases. Provide a plausible reason for why the boiling heat transfer coefficient for a given AT's for…
Region I Region II Maximum Region IV | critical) heat | flux. Film Nucleate boiling to Transition boiling boiling Natural convection 10 Minimum boiling Slugs and heat flux,4 Di min to columns- Isolated Region II bubbles 10 10 30 100 320 1000 AT=T,-T. (C) Figure 2. Boiling mechanisms for water. Table 1. Heating Resistor Features. Features and Benefits Power rating of 17.0608 Btu/min • Diameter of 10 mm Length of 65 mm Quartz resistance wire for maximum heater life • TIG-welded end disc prevents contamination and moisture absorption Fibreglass lead wire insulation • Complies with Electrostatic Control Standards ANSI/ESD S20.20:2014 and BS EN 61340-5- 1:2007 ROHS compliant on restricted hazardous substances 4 (W/m)
.All properties should be evaluated at the temperature of the steam.Saturated, pure steam at 65 ºC condenses on the surface of a vertical tube with outersurface diameter 2 cm which is maintained at a uniform temperature of 35 ºC. Determinethe tube length for a condensate flow rate of 5 x 10-3 kg/s.