If an object is heated, the temperature of the body will increase. The energy (Q) associated with a change in temperature (ΔT) is a function of the mass of the object (m) and the specific heat(Cp). In an experiment, heat is applied to the end of an object, and the temperature change at the other end of the object is recorded. This leads to the following equation.
An unknown material with a mass of = kilograms is tested in the lab, yielding the following results. Use the polyfit function to determine the specific heat of this material and store the final result in the variable Cp.
Create a proper plot of the data. Add a linear trendline, showing the resulting trend line equation, on the graph for a change in temperature over a range of energy from 5 joules to 70 joules.
Want to see the full answer?
Check out a sample textbook solutionChapter 18 Solutions
Thinking Like an Engineer: An Active Learning Approach (3rd Edition)
- Vibration Engineeringarrow_forwardA chamber of unknown volume is filled with an unknown amount of ideal gas. A cylinder with an open bottom and calibrated volume is connected to the chamber and is closed with a movable piston. A gas pressure sensor is also mounted on the chamber as shown in the figure. The whole experimental setup is kept at a constant temperature of 300 K. Doris moves the piston from mark 0 to mark 200 mL in steps of 50 mL and records the corresponding pressure in the chamber (see the table below). She moves the piston very slowly and waits several minutes before recording the pressure values. VCyl(mL) P(105N/m2)) 0 4.35 50 3.85 100 3.50 150 3.15 200 2.90 Determine the volume of the chamber using Doris's data in the table. (Note: This is a problem that requires linearization of data.) Determine the number of moles of gas. (Note: This is a problem that requires linearization of data.)arrow_forwardThe stress profile shown below is applied to six different biological materials: Log Time (s] The mechanical behavior of each of the materials can be modeled as a Voigt body. In response to o,= 20 Pa applied to each of the six materials, the following responses are obtained: 2 of Maferial 6 Material 5 0.12 0.10 Material 4 0.08 Material 3 0.06 0.04 Material 2 0.02 Material 1 (a) Which of the materials has the highest Young's Modulus (E)? Why? Log Time (s) (b) Using strain value of 0.06, estimate the coefficient of viscosity (n) for Material 6. Stress (kPa) Strainarrow_forward
- *Hi, please help me with this differential equations questions and please show the full solution. Thank you very much. * Question 1.) A load weighing 2 kg is attached to a spring. If the damping force is 5.5, spring constant is 4.2, and external force is sin(t), and the load is released from rest 0.2 inches below its equilibrium, determine the displacement of the object at any time t.arrow_forwardPLS USE THE ODD TABLE, MY LAST DIGIT NU IS 3arrow_forwardDon't Use Chat GPT Will Upvote And Give Handwritten Solution Pleasearrow_forward
- Question 13 Given, a 50 N bar is rotating downward at 2 rad/s. The spring has an un- stretched length of 2 m and a spring constant of 12 N/m. Find, the angle (measured down from the horizontal) to which the bar rotates before it stops its initial downward movement. [Ans : 47.5 deg] C 4 ft A B. 2 rad/s 6 ftarrow_forwardMechanical resistancearrow_forwardE and 5 v X O file:///C:/Users/Hp/Desktop/mm/OUTCOME%20NO.2%20and%205%20with%20Problems.pdf + O Fit to page D Page view A Read aloud 1 Add notes Problems 1. A brass rod of diameter 25 mm and length 250 mm is subjected to a tensile load of 50 kN and the extension of the rod is equal to 0.3 mm. Find the Young's Modulus or Modulus of Elasticity. 99+ to search hp delete prt sc 14 DI backs & 7 8 24 4 P EJR -0 J K H D. Farrow_forward
- A single degree-of-freedom linear elastic structure was subjected to a series of harmonic excitations, one at a time. The excitations had the same forcing magnitude but different forcing frequency. Forcing frequencies and observed peak steady-state displacements are shown in the graph below. Find the natural period and damping ratio of the structure. Displacement (mm) 60 50 40 30 20 10 0 0 1 2 . 3 4 Forcing frequency, f [Hz] 5 4. 6 7arrow_forwardQ2 A uniformly distributed force of C kN/m and a concentrated load of D kN are applied to a cantilever beam with a cross-section as shown in Figure Q2. By using the parameters listed in Table Q2. (a) Determine the support reaction of the cantilever beam. (b) Draw the shear and moment diagrams of the beam. (c) Determine the maximum bending moment, Mmax of the beam. (d) Determine the moment of inertia, I of the beam cross-section. (e) Calculate the maximum tensile and compressive stresses in the beam.arrow_forwarda) Sydney tap-water has a fluid electrical conductivity (EC or σ) of approximately 210μS/cm. Express this in terms of Ohm metres (resistivity) and mS/m (conductivity). b) The fluid electrical conductivity (EC) was measured on a water sample first at 25 °C to 305 μS/cm, then later at 20 °C to 272 μS/cm. Assuming a linear relationship, calculate the EC at 10 and 30 °C. c) A 20 cm long cylinder with 10 cm diameter is filled with an undisturbed fully saturated sandstone core. A current (I) of 100 mA was passed through the cylinder and a voltage(V) of 10,700 V was measured. Calculate the resistance and the resistivity of the sample. d) If we further know that the porosity is 1%, can you estimate the fluid electrical conductivity?arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY