VECTOR MECH...,STAT.+DYNA.(LL)-W/ACCESS
VECTOR MECH...,STAT.+DYNA.(LL)-W/ACCESS
11th Edition
ISBN: 9781259633133
Author: BEER
Publisher: MCG
bartleby

Concept explainers

bartleby

Videos

Question
Book Icon
Chapter 17.1, Problem 17.24P

(a)

To determine

Find the change in the angular velocity of the turbine disk.

(a)

Expert Solution
Check Mark

Answer to Problem 17.24P

The change in angular velocity of the turbine disk is Δω=0.250rpm_.

Explanation of Solution

Given information:

The mass of the turbine disk is mturbine=30kg.

The centroidal radius of gyration of the turbine disk is kturbine=175mm.

The angular velocity of the small blade is ω1=60rpm.

The weight of the small blade is Wblade=0.5N.

The centroidal radius of the blade is kblade=300mm

The angle the turbine disk rotates is θ=90°.

Position 1:

Find the mass of inertia about point O (I¯O) using the equation.

I¯O=mturbinekturbine2mbladekblade2=mturbinekturbine2Wbladegkblade2

Here, the acceleration due to gravity is g.

Consider the acceleration due to gravity is g=9.81m/s2.

Substitute 30 kg for mturbine, 175 mm for kturbine, 0.5 N for Wblade, 9.81m/s2 for g, and 300 mm for kblade.

I¯O=30×(175mm×1m1,000mm)20.59.81×(300mm×1m1,000mm)2=0.918754.58716×103=0.91416kgm2

Find the location of mass center (x¯) using the relation.

x¯=mbladerblademturbinemblade=(Wbladeg)rblademturbine(Wbladeg)

Position 1 (θ=0°):

The angular velocity at the position 1 is ω1=60rpm.

Find the total kinetic energy (T1) using the equation.

T1=12I¯Oω12

Substitute 0.91416kgm2 for I¯O and 60 rpm for ω1.

T1=12×0.91416×(60rpm×2πrad1rev×1min60s)2=18.04480J

Find the total potential energy (V1) using the equation.

V1=mturbinegh1mbladegh1

Here, the conditional center of gravity is h1.

In this case, the center of gravity lies at the point O. so, h1=0.

Substitute 0 for h1.

V1=mturbineg(0)mbladeg(0)=0

Position 2 (θ=90°):

Find the total kinetic energy (T2) using the equation.

T2=12I¯Oω22

Substitute 0.91416kgm2 for I¯O.

T2=12×0.91416×ω22=0.45708ω22

Find the total potential energy (V2) using the equation.

V2=mturbinegh2mbladegh2=mturbinegh2Wbladeh2

Here, the conditional center of gravity is h2.

In this case, the center of gravity lies at the point O. so,

h2=x¯=(Wbladeg)rblademturbine(Wbladeg).

Substitute (Wbladeg)rblademturbine(Wbladeg) for h2.

V2=(mturbinegWblade)(Wbladeg)rblademturbine(Wbladeg)

Substitute 30 kg for mturbine, 9.81m/s2 for g, 0.5 N for Wblade, and 300 mm for rblade.

V2=(30×9.810.5)(0.59.81)×300mm×1m1,000mm30(0.59.81)=293.8×0.01529129.94903=0.15Nm

Write the equation of conservation of energy as follows;

T1+V1=T2+V2

Substitute 18.04480 J for T1, 0 for V1, 0.45708ω22 for T2, and 0.15Nm for V2.

18.04480+0=0.45708ω22+0.15ω2=6.25702rad/s×1rev2πrad×60s1min=59.75rpm

Find the change in angular velocity (Δω) using the relation.

Δω=ω2ω1

Substitute 59.75 rpm for ω2 and 60 rpm for ω1.

Δω=59.7560=0.250rpm

Therefore, the change in angular velocity of the turbine disk is Δω=0.250rpm_.

(b)

To determine

Find the change in the angular velocity of the turbine disk.

(b)

Expert Solution
Check Mark

Answer to Problem 17.24P

The change in angular velocity of the turbine disk is Δω=0.249rpm_.

Explanation of Solution

Given information:

The mass of the turbine disk is mturbine=30kg.

The centroidal radius of gyration of the turbine disk is kturbine=175mm.

The angular velocity of the small blade is ω1=60rpm.

The weight of the small blade is Wblade=0.5N.

The centroidal radius of the blade is kblade=300mm

The angle the turbine disk rotates is θ=270°.

Position 1:

Find the mass of inertia about point O (I¯O) using the equation.

I¯O=mturbinekturbine2mbladekblade2=mturbinekturbine2Wbladegkblade2

Here, the acceleration due to gravity is g.

Consider the acceleration due to gravity is g=9.81m/s2.

Substitute 30 kg for mturbine, 175 mm for kturbine, 0.5 N for Wblade, 9.81m/s2 for g, and 300 mm for kblade.

I¯O=30×(175mm×1m1,000mm)20.59.81×(300mm×1m1,000mm)2=0.918754.58716×103=0.91416kgm2

Find the location of mass center (x¯) using the relation.

x¯=mbladerblademturbinemblade=(Wbladeg)rblademturbine(Wbladeg)

Position 1 (θ=0°):

The angular velocity at the position 1 is ω1=60rpm.

Find the total kinetic energy (T1) using the equation.

T1=12I¯Oω12

Substitute 0.91416kgm2 for I¯O and 60 rpm for ω1.

T1=12×0.91416×(60rpm×2πrad1rev×1min60s)2=18.04480J

Find the total potential energy (V1) using the equation.

V1=mturbinegh1mbladegh1

Here, the conditional center of gravity is h1.

In this case, the center of gravity lies at the point O. so, h1=0.

Substitute 0 for h1.

V1=mturbineg(0)mbladeg(0)=0

Position 3 (θ=270°):

Find the total kinetic energy (T3) using the equation.

T3=12I¯Oω32

Substitute 0.91416kgm2 for I¯O.

T3=12×0.91416×ω22=0.45708ω32

Find the total potential energy (V3) using the equation.

V3=mturbinegh3mbladegh3=mturbinegh3Wbladeh3

Here, the conditional center of gravity is h3.

In this case, the center of gravity lies at the point O. so,

h3=x¯=(Wbladeg)rblademturbine(Wbladeg).

Substitute (Wbladeg)rblademturbine(Wbladeg) for h3.

V3=(mturbinegWblade)((Wbladeg)rblademturbine(Wbladeg))

Substitute 30 kg for mturbine, 9.81m/s2 for g, 0.5 N for Wblade, and 300 mm for rblade.

V2=(30×9.810.5)((0.59.81)×300mm×1m1,000mm30(0.59.81))=293.8×0.01529129.94903=0.15Nm

Write the equation of conservation of energy as follows;

T1+V1=T3+V3

Substitute 18.04480 J for T1, 0 for V1, 0.45708ω22 for T2, and 0.15Nm for V2.

18.04480+0=0.45708ω320.15ω3=6.309247rad/s×1rev2πrad×60s1min=60.249rpm

Find the change in angular velocity (Δω) using the relation.

Δω=ω3ω1

Substitute 60.249 rpm for ω3 and 60 rpm for ω1.

Δω=60.24960=0.249rpm

Therefore, the change in angular velocity of the turbine disk is Δω=0.249rpm_.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
In conventional drawing of a stainless steel wire, the original diameter D.-3mm, the area reduction at each die stand r-40%, and the proposed final diameter D₁-0.5mm, how many die stands are required to complete this process.
A vertical true centrifugal casting process is used to produce bushings that are 250 mm long and 200 mm in outside diameter. If the rotational speed during solidification is 500 rev/min, determine the inside radii at the top and bottom of the bushing if R-2Rb. Take: 8-9.81 m/s
In non-continuous dieless drawing process for copper tube as shown in Fig. (1), take the following data: Do-20mm, to=3mm, D=12mm, ti/to=0.6 and vo-15mm/s. Calculate: (1) area reduction RA, (2) drawing velocity v. Knowing that: t₁: final thickness D₁ V. Fig. (1) D

Chapter 17 Solutions

VECTOR MECH...,STAT.+DYNA.(LL)-W/ACCESS

Ch. 17.1 - PROBLEM 17.6 The flywheel of a punching machine...Ch. 17.1 - Prob. 17.7PCh. 17.1 - Prob. 17.8PCh. 17.1 - The 10-in.-radius brake drum is attached to a...Ch. 17.1 - Prob. 17.10PCh. 17.1 - Prob. 17.11PCh. 17.1 - Prob. 17.12PCh. 17.1 - Prob. 17.13PCh. 17.1 - The double pulley shown has a mass of 15 kg and a...Ch. 17.1 - Gear A has a mass of 1 kg and a radius of gyration...Ch. 17.1 - Prob. 17.16PCh. 17.1 - Prob. 17.17PCh. 17.1 - A slender 9-lb rod can rotate in a vertical plane...Ch. 17.1 - An adapted golf device attaches to a wheelchair to...Ch. 17.1 - Prob. 17.20PCh. 17.1 - A collar with a mass of 1 kg is rigidly attached...Ch. 17.1 - A collar with a mass of 1 kg is rigidly attached...Ch. 17.1 - Two identical slender rods AB and BC are welded...Ch. 17.1 - Prob. 17.24PCh. 17.1 - Prob. 17.25PCh. 17.1 - Prob. 17.26PCh. 17.1 - Greek engineers had the unenviable task of moving...Ch. 17.1 - A small sphere of mass m and radius r is released...Ch. 17.1 - Prob. 17.29PCh. 17.1 - A half-cylinder with mass m and radius r is...Ch. 17.1 - Prob. 17.31PCh. 17.1 - Two uniform cylinders, each of weight W = 14 lb...Ch. 17.1 - Prob. 17.33PCh. 17.1 - A bar of mass m = 5 kg is held as shown between...Ch. 17.1 - The 1.5-kg uniform slender bar AB is connected to...Ch. 17.1 - The motion of the uniform rod AB is guided by...Ch. 17.1 - Prob. 17.37PCh. 17.1 - Prob. 17.38PCh. 17.1 - The ends of a 9-lb rod AB are constrained to move...Ch. 17.1 - The mechanism shown is one of two identical...Ch. 17.1 - The mechanism shown is one of two identical...Ch. 17.1 - Each of the two rods shown is of length L = 1 m...Ch. 17.1 - The 4-kg rod AB is attached to a collar of...Ch. 17.1 - If in Prob. 17.43 the angular velocity of the...Ch. 17.1 - 17.45 The uniform rods AB and BC weigh 2.4 kg and...Ch. 17.1 - The uniform rods AB and BC weigh 2.4 kg and 4 kg,...Ch. 17.1 - The 80-mm-radius gear shown has a mass of 5 kg and...Ch. 17.1 - Prob. 17.48PCh. 17.1 - Three shafts and four gears are used to form a...Ch. 17.1 - Prob. 17.50PCh. 17.1 - Prob. 17.51PCh. 17.2 - The 350-kg flywheel of a small hoisting engine has...Ch. 17.2 - Prob. 17.2IMDCh. 17.2 - Prob. 17.3IMDCh. 17.2 - Prob. 17.52PCh. 17.2 - Prob. 17.53PCh. 17.2 - Prob. 17.54PCh. 17.2 - A uniform 144-lb cube is attached to a uniform...Ch. 17.2 - Prob. 17.56PCh. 17.2 - Prob. 17.57PCh. 17.2 - Prob. 17.58PCh. 17.2 - Prob. 17.59PCh. 17.2 - Each of the double pulleys shown has a centroidal...Ch. 17.2 - Each of the gears A and B has a mass of 675 g and...Ch. 17.2 - Prob. 17.62PCh. 17.2 - Prob. 17.63PCh. 17.2 - Prob. 17.64PCh. 17.2 - Prob. 17.65PCh. 17.2 - Show that, when a rigid body rotates about a fixed...Ch. 17.2 - Prob. 17.68PCh. 17.2 - A flywheel is rigidly attached to a 1.5-in.-radius...Ch. 17.2 - A wheel of radius r and centroidal radius of...Ch. 17.2 - Prob. 17.71PCh. 17.2 - 17.72 and 17.73 A 9-in.·radius cylinder of weight...Ch. 17.2 - 17.72 and 17.73 A 9-in.·radius cylinder of weight...Ch. 17.2 - Two uniform cylinders, each of mass m = 6 kg and...Ch. 17.2 - Prob. 17.75PCh. 17.2 - Prob. 17.76PCh. 17.2 - A sphere of radius r and mass m is projected along...Ch. 17.2 - A bowler projects an 8.5-in.-diameter ball...Ch. 17.2 - Prob. 17.79PCh. 17.2 - A satellite has a total weight (on Earth) of 250...Ch. 17.2 - Two 10-lb disks and a small motor are mounted on a...Ch. 17.2 - Prob. 17.82PCh. 17.2 - Prob. 17.83PCh. 17.2 - Prob. 17.84PCh. 17.2 - Prob. 17.85PCh. 17.2 - Prob. 17.86PCh. 17.2 - Prob. 17.87PCh. 17.2 - Prob. 17.88PCh. 17.2 - A 1.8-kg collar A and a 0.7-kg collar B can slide...Ch. 17.2 - Prob. 17.90PCh. 17.2 - A small 4-lb collar C can slide freely on a thin...Ch. 17.2 - Rod AB has a weight of 6 lb and is attached to a...Ch. 17.2 - Prob. 17.93PCh. 17.2 - Prob. 17.94PCh. 17.2 - The 6-lb steel cylinder A of radius r and the...Ch. 17.3 - A uniform slender rod AB of mass m is at rest on a...Ch. 17.3 - Prob. 17.5IMDCh. 17.3 - Prob. 17.6IMDCh. 17.3 - At what height h above its center G should a...Ch. 17.3 - A bullet weighing 0.08 lb is fired with a...Ch. 17.3 - In Prob. 17.97, determine (a) the required...Ch. 17.3 - A 16-lb wooden panel is suspended from a pin...Ch. 17.3 - Prob. 17.100PCh. 17.3 - A 45-g bullet is fired with a velocity of 400 m/s...Ch. 17.3 - A 45-g bullet is fired with a velocity of 400 m/s...Ch. 17.3 - Prob. 17.103PCh. 17.3 - Prob. 17.104PCh. 17.3 - Prob. 17.105PCh. 17.3 - A uniform slender rod AB is at rest on a...Ch. 17.3 - A bullet of mass m is fired with a horizontal...Ch. 17.3 - Determine the height h at which the bullet of...Ch. 17.3 - A uniform slender bar of length L = 200 mm and...Ch. 17.3 - A uniform slender rod of length L is dropped onto...Ch. 17.3 - A uniform slender rod AB has a mass m, a length L,...Ch. 17.3 - 17.113 The slender rod AB of length L = 1 m forms...Ch. 17.3 - The trapeze/lanyard air drop (t/LAD) launch is a...Ch. 17.3 - The uniform rectangular block shown is moving...Ch. 17.3 - The 40-kg gymnast drops from her maximum height of...Ch. 17.3 - Prob. 17.117PCh. 17.3 - Prob. 17.118PCh. 17.3 - A 1-oz bullet is fired with a horizontal velocity...Ch. 17.3 - For the beam of Prob. 17.119, determine the...Ch. 17.3 - Prob. 17.121PCh. 17.3 - Prob. 17.122PCh. 17.3 - A slender rod AB is released from rest in the...Ch. 17.3 - Prob. 17.124PCh. 17.3 - Block A has a mass m and is attached to a cord...Ch. 17.3 - Prob. 17.126PCh. 17.3 - 17.127 and 17.128Member ABC has a mass of 2.4 kg...Ch. 17.3 - 17.127 and 17.128Member ABC has a mass of 2.4 kg...Ch. 17.3 - Prob. 17.129PCh. 17.3 - Prob. 17.130PCh. 17.3 - A small rubber ball of radius r is thrown against...Ch. 17.3 - Sphere A of mass m and radius r rolls without...Ch. 17.3 - In a game of pool, ball A is rolling without...Ch. 17 - A uniform disk, initially at rest and of constant...Ch. 17 - The 8-in.-radius brake drum is attached to a...Ch. 17 - A uniform slender rod is placed at corner B and is...Ch. 17 - The motion of the slender 250-mm rod AB is guided...Ch. 17 - Prob. 17.141RPCh. 17 - Disks A and B are made of the same material, are...Ch. 17 - Disks A and B are made of the same material, are...
Knowledge Booster
Background pattern image
Mechanical Engineering
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.
Similar questions
SEE MORE QUESTIONS
Recommended textbooks for you
Text book image
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Text book image
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Text book image
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Text book image
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Text book image
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Text book image
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
moment of inertia; Author: NCERT OFFICIAL;https://www.youtube.com/watch?v=A4KhJYrt4-s;License: Standard YouTube License, CC-BY