(a) Explanation Given information: The mass of slender rod is m . The length of slender rod is L . The impact at D is perfectly plastic. The length b is 0.6 L . Calculation: The motion is falling motion before impact. Consider the position 1 is before impact. Sketch the position 1 of the rod as shown in Figure (1). Consider the position 2 is just before impact. (The rod is in horizontal position). Sketch the position 2 of the rod as shown in Figure (2). Refer Figure (2), Before the impact the rotation is about point A . Write the equation of velocity ( v ¯ 2 ) of rod before impact. v ¯ 2 = L 2 ω 2 Here, ω 2 is the angular velocity of rod at position 2. At position 1, the rod is at rest. Therefore, the kinetic energy of rod ( T 1 ) at position 1 is zero. Write the equation of potential energy ( V 1 ) of rod at position 1. V 1 = m g L 4 At position 2, the rod is in horizontal position. Therefore, the potential energy of rod ( V 2 ) at position 2 is zero. Write the equation of kinetic energy ( T 2 ) of rod at position 2. T 2 = 1 2 m ( L 2 ω 2 ) 2 + 1 2 ( 1 12 m L 2 ) ω 2 2 = 1 6 m L 2 ω 2 2 Apply conservation of energy for position 1 and 2. T 1 + V 1 = T 2 + V 2 Substitute 0 for T 1 , m g L 4 for V 1 , 1 6 m L 2 ω 2 2 for T 2 , and 0 for V 2 . T 1 + V 1 = T 2 + V 2 0 + m g L 4 = 1 6 m L 2 ω 2 2 + 0 ω 2 2 = m g L 4 × 6 m L 2 ω 2 2 = 3 g 2 L ω 2 = 3 g 2 L Consider the impulse and momentum principle. Syst Momenta 1 + Syst Ext Imp 1y2 = Syst Momenta 2 Sketch the impulse and momentum diagram of the system as shown in Figure (3). Refer Figure (3). Take moments about D (anticlockwise moment as positive). I ¯ ω 2 − m v ¯ 2 ( L 10 ) = I ¯ ω 3 + m v ¯ 3 ( L 10 ) (1) Here, v ¯ 3 is the angular velocity of rod just after the impact. Consider the position 3 is just after impact. Sketch the position 3 of the rod as shown in Figure (4) (b) To determine The maximum angle through which the rod will rotate after the impact.

11th Edition

ISBN: 9781259633133

Author: BEER

Publisher: MCG

See similar textbooks

Concept explainers

Thermal Properties of Materials

In mechanical engineering, the thermal property is represented as the physical quantity that is relevant to the application of heat. The thermal properties are evaluated by variations in any specific material due to low heat or high heat. The quantities …

Videos

Question

Chapter 17.3, Problem 17.117P

(a)

To determine

The angular velocity of the rod immediately after the impact.

(b)

To determine

The maximum angle through which the rod will rotate after the impact.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 17.3, Problem 17.116P

Chapter 17.3, Problem 17.118P

Students have asked these similar questions

2. Express the following complex numbers in rectangular form. (a) z₁ = 2еjл/6 (b) Z2=-3e-jπ/4 (c) Z3 = √√√3e-j³/4 (d) z4 = − j³

A prismatic beam is built into a structure. You can consider the boundary conditions at A and B to be fixed supports. The beam was originally designed to withstand a triangular distributed load, however, the loading condition has been revised and can be approximated by a cosine function as shown in the figure below. You have been tasked with analysing the structure. As the beam is prismatic, you can assume that the bending rigidity (El) is constant. wwo cos 2L x A B Figure 3: Built in beam with a varying distributed load In order to do this, you will: a. Solve the reaction forces and moments at point A and B. Hint: you may find it convenient to use the principal of superposition. (2%) b. Plot the shear force and bending moment diagrams and identify the maximum shear force and bending moment. (2%) c. Develop an expression for the vertical deflection. Clearly state your expression in terms of x. (1%)

Question 1: Beam Analysis Two beams (ABC and CD) are connected using a pin immediately to the left of Point C. The pin acts as a moment release, i.e. no moments are transferred through this pinned connection. Shear forces can be transferred through the pinned connection. Beam ABC has a pinned support at point A and a roller support at Point C. Beam CD has a roller support at Point D. A concentrated load, P, is applied to the mid span of beam CD, and acts at an angle as shown below. Two concentrated moments, MB and Mc act in the directions shown at Point B and Point C respectively. The magnitude of these moments is PL. Moment Release A B с ° MB = PL Mc= = PL -L/2- -L/2- → P D Figure 1: Two beam arrangement for question 1. To analyse this structure, you will: a) Construct the free body diagrams for the structure shown above. When constructing your FBD's you must make section cuts at point B and C. You can represent the structure as three separate beams. Following this, construct the…

Chapter 17 Solutions

VECTOR MECH...,STAT.+DYNA.(LL)-W/ACCESS

Ch. 17.1 - A round object of mass m and radius r is released...Ch. 17.1 - Prob. 17.2CQ Ch. 17.1 - Prob. 17.3CQ Ch. 17.1 - Prob. 17.4CQ Ch. 17.1 - Slender bar A is rigidly connected to a massless...Ch. 17.1 - A 200-kg flywheel is at rest when a constant 300...Ch. 17.1 - The rotor of an electric motor has an angular...Ch. 17.1 - Prob. 17.3P Ch. 17.1 - Two disks of the same material are attached to a...Ch. 17.1 - Prob. 17.5P

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.