A cast iron cylinder of 200 mm inner diameter and 12.5 mm thick is closely wound with a layer of 4 mm diameter steel wire under a tensile stress of 55 MN/m². Determine the stresses set up in the cylinder and steel wire if water under a pressure of 3 MN/m² is admitted in the cylinder. Take E= 100 GN/m², E = 200 GN/m² and Poisson's ratio = 0.25.

A cast iron cylinder of 200 mm inner diameter and 12.5 mm thick is closely wound with a layer of 4 mm diameter steel wire under a tensile stress of 55 MN/m². Determine the stresses set up in the cylinder and steel wire if water under a pressure of 3 MN/m² is admitted in the cylinder. Take E= 100 GN/m², E = 200 GN/m² and Poisson's ratio = 0.25.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. A steel rod of 20 mm diameter passes centrally through a copper tube of external diameter 40 mm and internal diameter 20 mm. The tube is closed at each end with the help of rigid washers (of negligible thickness) which are screwed by the nuts. The nuts are tightened until the compressive load on the copper tube is 50 kN. Determine the stresses in the rod and the tube, when the temperature of whole assembly falls by 50°C. Take Es = 200 GPa ; Ec = 100 GPa ; as = 12 x 10-6/°C and ac = 18 x 106/°C.
2. The tank shown in the figure is fabricated from 10 mm steel plate. Determine the maximum longitudinal and circumferential stress caused by an internal pressure of 1.2 MPa. 400mm 600 mm
Extensometers attached to the external surface of a pressure vessel indicate that a = 0.002 and & = 0.005 along the longitudinal and transverse directions, respectively. Determine the corresponding stresses for E= 210 GPa and v = 0.4. What would be the error in these stresses if Poisson's ratio were not considered?
The inner diameter of the AB compressed air tank is 160, the wall thickness is 1.Since the manometer pressure in the tank is 1,6 ,at point a at the top of the tank maximum normal stress and determine the maximum plane shear stress.(c=16 , d=38, e =32, g=160, h=1, k =1.6 , F=160)
The normal strain measured on the outside surface of a spherical pressure vessel is 670 με.The sphere has an outside diameter of 1.20 m and a wall thickness of 10 mm, and it will befabricated from an aluminum alloy [E = 73 GPa;ν = 0.33]. Determine (a) the normal stress inthe vessel wall and (b) the internal pressure in the vesssel
A standpipe with an inside diameter of 108 in. contains water, which has a weight density of Y=62.4 Ib/ft³. The column of water stands h=30 ft above an outlet pipe, which has an outside diameter of 6.625 in. and an inside diameter of 6.065 in. (a) Determine the longitudinal and hoop stresses in the outlet pipe at B. (Pressure at the outlet is P=Y*h) (b) If the maximum hoop stress in the standpipe at point A must be limited to2,500 psi, determine the minimum wall thickness that can be used for the standpipe.
The spherical pressure hull of the undersea submarine, under a research study shown in the figure below, has a 1 meter radius with a shell thickness of 30mm. The pressure hull is made of steel having a yield point of 700 MPa. Consider sea water to have a constant specific weight of 10kN/m³. Determine the depth pressure of submergence that would setup the yield point stress in the spherical shell. Use:p = yy, where y is the depth r = 1m t = 30mm comex
* Your answer is incorrect. A spherical rubber balloon is blown up until its diameter is three times the initial diameter. If E = 10750 psi and v=0.46, determine the stresses in the balloon. Assume the stress-strain behavior is linear. Answer: 0 = 268.75 ksi
The storage capacity of a thin cylindrical pressure vessel is 0.028 m³. The cylinder is subjected to an internal pressure of 21 MPa. The length of the cylinder is twice its internal diameter. Determine all the dimensions of the cylinder, if (a) the longitudinal stress does not exceed 160 MPa; and (b) the circumferential stress does not exceed 235 Mpa.
A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 20 mm. The diameter of the pressure vessel is 450 mm and its length is 2.0 m. Determine the maximum internal pressure that can be applied if the longitudinal stress is limited to 140 МРа, and the circumferential stress is limited to 60 МРа. A spherical shell with 70-in. outer diameter and 67-in. inner diameter contains helium at a pressure of 1200 psi. Compute the stress in the shell.
Air pressure in the cylinder is increased by exerting forces P = 3 kN on the two pistons, each having a radius of 45 mm. The cylinder is shown in the figure below. If the cylinder has a wall thickness of 2 Mm, determine the circumferential stress in the wall of the cylinder. Express your answer to three significant figures and include appropriate units.
The ring, with dimensions shown, is placed over a flexible membrane which is pumped up with a pressure p. The thickness r,-r; is small compared to r; (a) Determine the axial force F in the ring in terms of p, w and r;. Hint: Consider a FBD by cutting the ring+membrane in two. (b) Determine the hoop stress in the ring. (c) Determine the hoop strain in the ring. The modulus of elasticity for the ring is E. (d) Relate the hoop strain to the change in the inner radius of the ring after this pressure is applied, and use this to get the change in the inner radius in terms of p, E, w, r, and ri- (PLEASE ANSWER ASAP AND CORRECTLY)!