You are asked to design a unit to condense ammonia. The required condensation rate is 0.09kg/s. Saturated ammonia at 30 o C is passed over a vertical plate (10 cm high and 25 cm wide).The properties of ammonia at the saturation temperature of 30°C are hfg = 1144 ́10^3 J/kg andrho_v = 9.055 kg/m 3 . Use the properties of liquid ammonia at the film temperature of 20°C (Ts =10 o C):Pr = 1.463 rho_l= 610.2 kf/m^3 liquid viscosity= 1.519*10^-4 kg/ ms kinematic viscosity= 2.489*10^-7 m^2/s Cpl= 4745 J/kg C kl=0.4927 W/m C hfg*=hfg+0.68Cpl(Tsat-Given Ts) a) Instead of one plate you want to use small plates and install many of them. Calculate the requiredsurface temperature to achieve the desired condensation rate (0.09 kg/s) if you install 36vertical plates (with the same dimension as above: 10 cm high and 25 cm wide).

You are asked to design a unit to condense ammonia. The required condensation rate is 0.09kg/s. Saturated ammonia at 30 o C is passed over a vertical plate (10 cm high and 25 cm wide).The properties of ammonia at the saturation temperature of 30°C are hfg = 1144 ́10^3 J/kg andrho_v = 9.055 kg/m 3 . Use the properties of liquid ammonia at the film temperature of 20°C (Ts =10 o C):Pr = 1.463 rho_l= 610.2 kf/m^3 liquid viscosity= 1.51910^-4 kg/ ms kinematic viscosity= 2.48910^-7 m^2/s Cpl= 4745 J/kg C kl=0.4927 W/m C hfg*=hfg+0.68Cpl(Tsat-Given Ts) a) Instead of one plate you want to use small plates and install many of them. Calculate the requiredsurface temperature to achieve the desired condensation rate (0.09 kg/s) if you install 36vertical plates (with the same dimension as above: 10 cm high and 25 cm wide).

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter8: Natural Convection

Section: Chapter Questions

Problem 8.28P

See similar textbooks

Similar questions

Water boils at 100°C at atmospheric pressure, that is, at sea level (To=15ºC). The boiling point is defined as the temperature at which the vapor pressure of water is equal to the atmospheric pressure. This has consequences for cooking in places such as Atok where it takes quite a bit longer to make a hard-boiled egg than it would in Baguio City. If the albumen in an egg needs to reach 75°C for the protein to coagulate, at what height would it be impossible to hard boil an egg?
4. 1.00 mol of water at 25°C evaporated on a steel plate heated to 150°C. Calculate ASwater, Splate, and AStotal using the given values. Cp(HzO(I)) Cp(H2O(g)) AHvap (water) Normal boiling point(water) 75.4 J/(K.mol) 36.0 J/(K.mol) 40.68 KJ/mol 100°C
At the pressure of P=0.1MPa, the saturation temperature of water is Tsat=100 ºC, the specific volume of the saturated liquid water is vf=0.001043 m3/kg, and the specific volume of the saturated vapor water is vg=1.6720 m3/kg. (3) Please match regions shown in the diagram with correct names.
Please read and solve this question carefully and circle the final answer ( Write clear) Use image below
please help me with this
0.110 mol of argon gas is admitted to an evacuated 60 cm^3 container 50 degrees C. The container is then sealed and the gass undergoes an isochoric heating to a temperature of 500 degrees C. a. What is the final pressure of the gas? (in kPa).
i need the answer quickly
Use the Kedzierski (2003) refrigerant/lubricant mixture pool boiling model to predict the boiling heat transfer coefficient (hm) for a range of superheats (4T, = 8 K to 40 K) and Ts = 277.6 K: 5.9×107(1−x,)ph ATk, (1-e*) x, To Where 1₂ %₁ = = 9m T-T Г x Τσ PL-Pbx 5.9×107(1-x₂)ph AT 0.755lp₁ (1-x₁) _ 18.75Ãµ₁ (1—x₁) _ 18.75×10¯¹º[m]p, (1-x₂) Xp Prv XpPrv XpPrv Assume that λ = 1.34 for xb=0.005 and that λ = 0.3 for Xb = 0.02. The properties of the refrigerant (R123) at the film temperature are: KL (W/mK) 0.139 R123 Or (N/m) 179692.3 0.01764 hfg (J/kg) The properties of the mineral oil (lubricant) are: PL (kg/m³) 917.8 York-C VL (cSt) 60 Prv (kg/m³) 2.701 VL (m²/s) 6 × 10-5 OL (N/m) 0.026 1.) Plot hm vs ATs and le vs ATs for two lubricant mass fractions: x = 0.005 (use 2 = 1.34 for Xb = = 0.005) and x = 0.02 (use λ = 0.3 for xb = 0.02). Compare the predicted ro for the two mass fraction cases. Provide a plausible reason for why the boiling heat transfer coefficient for a given AT's for…
Hi, please provide the need solution for this problem. The final answer is already provided below. Thank you so much. *** Determine the result when 100g of steam at 100C is passed into 200g of water and 20g of ice at exactly 0C in a calorimeter which behaves thermally as if it were equivalent to 30g of water. Answer: 49 grams of steam condense, final temperature 100°C
What is the mass flow rate of zinc in the scrap brass stream (ṁZn,3) in kg/h to 0 decimal place? What is the mass fraction of copper in the mixed scrap stream (xCu,4) to 2 decimal places?
By writing E and S as functions of T and P, obtain the following expressions for the differentials dE and dF: dE = (CP-PVb)dt + V(kb-bT)dP and dF = -(PVb+S)dT+PVkdP. β and κ are the isobaric thermal expansion coefficient and the isothermal compressibility, respectively.
The initial state of 1.00 mol of a dilute gas is P1 = 3.00 atm, V1 = 1.00 L, and Eint1 = 456 J and its final state is ?2 = 2.00 atm, V2 = 3.00 L, and Eint 2 = 912 J. The gas is heated and is allowed to expand such that it follows a single straight-line path on a PV diagram from its initial state to its final state. (a) Illustrate this process on a PV diagram and calculate the work done by the gas. (b) Find the heat absorbed by the gas during this process.