A steel alloy contains 95.7 wt% Fe, 4.0 wt% W,and 0.3 wt% C. (a) What is the eutectoid temperature of this alloy?(b) What is the eutectoid composition?(c) What is the proeutectoid phase?Assume that there are no changes in the positionsof other phase boundaries with the addition of W.

Given Data:The alloy contains:95.7 wt% Fe (Iron)4.0 wt% W (Tungsten)0.3 wt% C (Carbon)It is…

Answered: A steel alloy contains 95.7 wt% Fe, 4.0…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the tensile strength, yield strength and percentage elongation (% ductility) for an iron- carbon alloy with 0.76 wt % carbon composition. O Yield strength - 60000 psi : Tensile strength - 110000 psi: Ductility - 15% O Yield strength - 130000 psi : Tensile strength - 68000 psi;: Ductility - 10% O Yield strength - 68000 psi : Tensile strength - 130000 psi; Ductility - 10% O Yield strength 50000 psi: Tensile strength - 100000 psi: Ductility - 20% O Yield strength - 86000 psi : Tensile strength 150000 psi: Ductility 25%
A 609 g eutectoid steel ( about 0.8%C) is heated to 1,002 C and cooled slowly through the eutectorid temperature. This results in the formation of cementite Fe3C (6.67%C) and ferrite (0.025%C). Calculate the number of grams of cementite that form in the steel.
Problem 1 A 0.65 percent C hypoeutectoid plain-carbon steel is slowly cooled from about 950°C to a temperature just slightly above 723°C. Calculate the weight percent austenite and weight percent proeutectoid ferrite in this steel. a +y a a 0.02% C 0.65% C 0.80% C
These questions are based on a high carbon stell with a composition of 1.5%C and 98.5%Fe 1)Name the phases present and calculate the amounts of these phases just above the eutectoid temperature. 2)With equilibrium cooling just below the eutectoid temperature calculate the total ferrite.
Specify the number of degree of freedom for the following alloys. Refer to the pictures below. A) 95 wt% Ag-5 wt% Cu at 780C B) 2.5 wt% C-97.5 wt% Fe at 1000C
Question 1 You are working on a design team at a small orthopaedic firm. You have been asked to select a cobalt- chrome-molybdenum (CoCr) material that will not experience plastic deformation under a specific mechanical test, as follows... A tensile stress is applied along the long axis of a solid cylindrical rod that has a diameter of 10 mm. An applied load of some magnitude F produces a 7x10-³ mm change in diameter (see figure below, original shape is blue, elongated shape is unshaded). Q1A-B: Calculate the transverse strain in the x-direction (Ex) associated with the reduction in diameter. Calculate the axial strain in the z-direction (₂) associated with the length increase.
Determine the structural constitution of a steel with 0.4% carbon at 727ºC during its cooling. Suggestion: Calculate using the lever rule
An engineer is making determinations on the best alloy of steel to use in cables for a cable-stayed bridge. The investigator’s tool is a tensile testing instrument which can measure the strength of the alloys by slowly increasing the load on the cable to the point where the cable breaks and breaking point value (amount of weight on the cable when it fails) can be accurately measured. The investigator also is interested in determining the amount of deformation of the cable (how much it stretches under load conditions which is also very important in structural considerations. The tests must be uniform and consistent to give the precision needed to make valid conclusions about the best alloy for the cables. On the line after the item, identify which type of variable it represents from (a) independent variable, (b) dependent variable, (c) control variable. 1) thickness of the cable _____________ 5) length of the cable _____________ 2) testing room temperature…
Show full work from basic,Thanks
The Fe-C phase diagram is given: How much of the Primary phase for a Fe-0.55% C alloy forms at 500°C? What is the weight fraction of the total cementite for the same alloy at 500°C? Composition (at% C) 5 10 15 20 25 1600 1538°C 1493°C L 1400 2500 1394°C y+L 1200 1147°C 2.14 4.30 Y, Austenite 2000 1000 912°C y+ Fe3C 800 1500 727°C 0.76 0.022 600 `a, Ferrite a + Fe3C Cementite (Fe3C) 1000 400 1 4 6. 6.70 (Fe) Composition (wt% C) Temperature (°C) Temperature (°F)
For the alloy Mg-45 wt% alloy at 500 C, what is the weight percentage of Pb in the alpha phase?
Please don't provide handwritten solution .....

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

A steel alloy contains 95.7 wt% Fe, 4.0 wt% W, and 0.3 wt% C. (a) What is the eutectoid temperature of this alloy? (b) What is the eutectoid composition? (c) What is the proeutectoid phase? Assume that there are no changes in the positions of other phase boundaries with the addition of W.