Explanation Given data: Refer to Figure 16.37 in the textbook. The value of current source is, i s ( t ) = [ 6 u ( t ) + 3 δ ( t ) ] mA (1) Formula used: Write a general expression to calculate the impedance of a resistor in s -domain. Z R = R (2) Here, R is the value of resistance. Write a general expression to calculate the impedance of an inductor in s -domain. Z L = s L (3) Here, L is the value of inductance. Calculation: The given circuit is redrawn as shown in Figure 1. Apply Laplace transform for equation (1) to find I s ( s ) . I s ( s ) = [ 6 s + 3 ( 1 ) ] m { ∵ L ( u ( t ) ) = 1 s L ( δ ( t ) ) = 1 } = [ 6 s + 3 ] 10 − 3 { ∵ 1 m = 10 − 3 } Substitute 2 Ω for R 1 in equation (1) to find Z R 1 . Z R 1 = 2 Substitute 1 Ω for R 2 in equation (1) to find Z R 2 . Z R 2 = 1 Substitute 0.2 H for L in equation (2) to find Z L . Z L = s ( 0.2 H ) = 0.2 s Convert the Figure 1 into s -domain as shown in Figure 2. Use source transformation method to convert the current source into voltage source. V s ( s ) = ( 2 ) [ 6 s + 3 ] 10 − 3 = [ 12 s + 6 ] 10 − 3 Now, the Figure 2 is reduced as shown in Figure 3. Refer to Figure 3, the resistors and inductor is connected in series. The equivalent impedance is calculated as follows: Z eq = 2 + 1 + 0.2 s = 3 + 0.2 s Now, the Figure 3 is reduced as shown in Figure 4. The current I ( s ) is calculated as follows: I ( s ) = ( 12 s + 6 ) 10 − 3 Z eq Substitute 3 + 0.2 s for Z eq in above equation to find I ( s ) . I ( s ) = ( 12 s + 6 ) 10 − 3 3 + 0.2 s = ( 12 + 6 s s ) 10 − 3 3 + 0.2 s = ( 6 s + 12 ) 10 − 3 0.2 s ( s + 15 ) = 5 ( 6 s + 12 ) 10 − 3 s ( s + 15 ) Simplify the above equation to find I ( s ) . I ( s ) = ( 30 s + 60 ) 10 − 3 s ( s + 15 ) (4) Take partial fraction for above equation

6th Edition

ISBN: 9780078028229

Author: Charles K Alexander, Matthew Sadiku

Publisher: McGraw-Hill Education

See similar textbooks

Question

Chapter 16, Problem 14P

To determine

Find the expression of current i(t) for the circuit shown in Figure 16.37.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 16, Problem 13P

Chapter 16, Problem 15P

Students have asked these similar questions

Using the table below, design a third (3th) order Butterworth HPF with a 4 KHz cutoff frequency. What is the additional stage required to HPF to design a third order BPF. Explain your answe Order Stage poles DF 2 stage poles 3 stage DF poles DF 1 1 Optional 2 1.414 3 י 1 1 2 1.848 2 0.765 5 2 1 1.618 1 0.618 6 2 1.932 1.414 2 0.518

.I need the correct answer, and if it's wrong, please fix it 7. The midrange voltage gain of an amplifier is 100. The input RC circuit has a lower critical frequency of 1 kHz. The actual voltage gain at f-100 Hz is 100. 10. In a high-pass filter, the roll-off region occurs above the critical frequency.

Solve this problem and show all of the work

Chapter 16 Solutions

Fundamentals of Electric Circuits

Ch. 16.2 - Determine vo(t) in the circuit of Fig. 16.6,...Ch. 16.2 - Prob. 2PP Ch. 16.2 - Prob. 3PP Ch. 16.3 - For the circuit shown in Fig. 16.12 with the same...Ch. 16.3 - Prob. 5PP Ch. 16.3 - The initial energy in the circuit of Fig. 16.17 is...Ch. 16.4 - Prob. 7PP Ch. 16.4 - Prob. 8PP Ch. 16.4 - Prob. 9PP Ch. 16.5 - Obtain the state variable model for the circuit...

Knowledge Booster

Find the expression of current i ( t ) for the circuit shown in Figure 16.37.

Solution Summary: The author explains how to find the expression of current i(t) for the circuit shown in Figure 16.37.

Find the expression of current i(t) for the circuit shown in Figure 16.37.

Want to see the full answer?

Chapter 16 Solutions