Liquid octane (C8H18) enters a steady-flow combustion chamber at 25°C and 8 atm at a rate of 0.8 kg/min. It is burned with 200 percent excess air that is compressed and preheated to 500 K and 8 atm before entering the combustion chamber. After combustion, the products enter an adiabatic turbine at 1300 K and 8 atm and leave at 950 K and 2 atm. Assuming complete combustion and T0 = 25°C, determine (a) the heat transfer rate from the combustion chamber, (b) the power output of the turbine, and (c) the reversible work and exergy destruction for the entire process.
(a)
The rate of heat transfer from the combustion chamber.
Answer to Problem 114RP
The rate of heat transfer from the combustion chamber is
Explanation of Solution
Write the energy balance equation using steady-flow equation.
Here, the total energy entering the system is
Substitute
Here, the enthalpy of formation for product is
Calculate the molar mass of the
Here, the number of carbon atoms is
Determine the rate of mole flow rates of the product.
Here, the mass flow rate is
Determine the heat transfer rate from the combustion chamber.
Conclusion:
Perform unit conversion of temperature at state 1 from degree Celsius to Kelvin.
For air temperature enter in the combustion chamber,
Write the combustion equation of 1 kmol for
Here, liquid octane is
Express the stoichiometric coefficient of air by
Substitute
Refer Appendix Table A-18, A-19, A-20, and A-23, obtain the enthalpy of formation, at 298 K, 500 K, 950 K, and 1500 K for
Substance | |||||
-249,950 | --- | --- | --- | --- | |
0 | 14,770 | 8682 | 42,033 | 26,652 | |
0 | 14,581 | 8669 | 40,170 | 28,501 | |
-241,820 | --- | 9904 | 48,807 | 33,841 | |
-393,520 | --- | 9364 | 59,552 | 40,070 |
Refer Equation (X), and write the number of moles of reactants.
Here, number of moles of reactant octane, oxygen and nitrogen is
Refer Equation (X), and write the number of moles of products.
Here, number of moles of product carbon dioxide, water, oxygen and nitrogen is
Substitute the value from table (I) of substance in Equation (II).
Therefore the heat transfer for
Substitute 8 for
Substitute
Substitute
Thus, the rate of heat transfer from the combustion chamber is
(b)
The rate of power output of the turbine.
Answer to Problem 114RP
The rate of power output of the turbine is
Explanation of Solution
Determine the power output of the adiabatic turbine from the steady-flow energy balance equation for non-reacting gas mixture.
Determine the rate of work done of the adiabatic turbine.
Conclusion:
Substitute the value from table (I) of substance in Equation (XI).
Substitute
Thus, the rate of power output of the turbine is
(c)
The exergy destruction rate from the combustion chamber.
The rate of reversible work done in the combustion chamber.
Answer to Problem 114RP
The exergy destruction rate from the combustion chamber is
The rate of reversible work done in the combustion chamber is
Explanation of Solution
Write the expression for entropy generation during this process.
Write the combustion equation of Equation (VI)
Here, the entropy of the product is
Determine the entropy at the partial pressure of the components.
Here, the partial pressure is
Determine the entropy generation rate from the combustion chamber.
Write the expression for exergy destruction during this process.
Here, the thermodynamic temperature of the surrounding is
Determine the rate of the reversible work done of the combustion chamber.
Conclusion:
Refer Equation (XV) for reactant and product to calculation the entropy in tabular form as:
For reactant entropy,
Substance |
(T, 1 atm) | ||||
1 | 1.00 | 360.79 | 17.288 | 360.79 | |
37.5 | 0.21 | 220.589 | 4.313 | 8,110.34 | |
141 | 0.79 | 206.630 | 15.329 | 26,973.44 | |
For product entropy,
Substance |
(T, 1 atm) | ||||
8 | 0.0437 | 266.444 | -20.260 | 2,293.63 | |
9 | 0.0490 | 230.499 | -19.281 | 2,248.02 | |
25 | 0.1366 | 241.689 | -10.787 | 6,311.90 | |
141 | 0.7705 | 226.389 | 3.595 | 31,413.93 | |
Substitute
Substitute
Substitute
Thus, the exergy destruction rate from the combustion chamber is
Substitute
Thus, the rate of reversible work done in the combustion chamber is
Want to see more full solutions like this?
Chapter 15 Solutions
CENGEL'S 9TH EDITION OF THERMODYNAMICS:
- If one mole of air/fuel mixture (rigid diatomic gas) is initially at 20◦C, is compressed and expanded 7-fold as part of the Otto cycle, and 4 kJ of heat is generated by burning the air/fuel mixture, calculate: (i) the temperature after each stage of the Otto cycle; (ii) the heat absorbed/expelled during each stage of the cycle; and (iii) the efficiency of the Otto cycle.arrow_forwardAcetylene gas (C2H2) is completely burned with 20 percent excess air in the steady-current combustion process. Fuel and the air enters the combustion chamber at 25 ° C and the products exit at a temperature of 1227 ° C. During this process Calculate the heat transfer that occurs.arrow_forwardEthane (C2H6) is burned with 20% excess air during a combustion process. Assuming completecombustion and a total pressure of 100 kPa, determine:1. the A/F ratio.2. the dew point temperature of the products.arrow_forward
- The reactant side has the following volumetric analysis for fuels burned simultaneously: CH₄= 68% and C₂H6= 32%. Assume a complete combustion with 15% excess air at 101.325 kPa, what is the partial pressure of water vapor in kPa.arrow_forwardA furnace burns natural gas at a rate of 10 m³n/s, with 10% excess air. The composition of natural gas is: CO₂ = 0,2%, CH4 = 90,0%, C₂H6- 5,0%, C3H8 = 1,5%, C4H10 = 0,5%, C5H12 = 0,1%, N₂= 2,7%.. Assume complete combustion of the gas. a) The volume of CO₂, H₂O and Air (m³); b) Air consumption in the boiler (in m³n/h); c) The total volume of gases produced (in m³n/h).arrow_forwardHelp!arrow_forward
- A gaseous fuel is burned in the combustion chamber at a rate of 400 L/a with a theoretical air-fuel ratio of 11.3 m^3 air/m^3 fuel. The air at 27°C and 101.3 kPa is supplied by a fan with a static pressure of 60 mmH2O. If the fuel is burned with 50% excess air, the discharge duct diameter is 0.55 m and fan efficency Is 68%, determine: a.) the fan capacity in m^3/s b.)the total head in mH2O c.) the brake power (in kW) needed to drive the fanarrow_forwardhow do you apply the 80 percent of the exceeded air to the combustion equation, as there is a ratio of 1.8 and 0.8 in places? also explain how from the energy balance equation the Qout was obtained?arrow_forwardFor complete combustion of octane (C3H,3) with 100% dry air. (a) write the balance mol equation (b) calculate the specific heat, enthalpy and internal energy of dry flue gas at 373 K. From Table A-1 specific heats in kJ/kg K: for CO2, Cp = 0.8452 ; for N2, Cp = 1.0414arrow_forward
- Isooctane is burned with theoretical air with 20% excess air during the combustion process in a small 3 – cylinder turbocharged automobile engine. Calculate: 1. Air – fuel ratio 2. Fuel – air ration 3. Equivalence ratio Stoichiometric reaction: _C3H8 + 02 + N2 → _CO2+ _H,0 + N2 With 20% excess air: _C3H8 + 02 + N2 →, CO2 + _H20 +. N2arrow_forwardThe stoichiometric air/gasoline (C7.76H13.1) mixture burns adiabatically. of the mixture Its temperature is 600 K. Calculate the flame temperature. for the solution of the energy equation Use the Heywood tables inside. |arrow_forwardThe fuel has the following volumetric analysis: CH4 = 60% C2H6 = 40% Assume complete combustion with 25% excess air at 101.325 kPa and 27 degrees dry bulb temperature. What is the actual fuel-air ratio?arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY