Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 11, Problem 6ASRQ
Technician A uses a micrometer to measure the connecting rod journal for taper. Technician B uses a micrometer to measure the connecting rod journal for out-of-roundness. Who is correct?
- Technician A
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Technician A tests brake drums for out-of-round using a dial indicator. Technician B measures the drum diameter in several places to check for out-of-round. Who is correct?
Identify the part not belonging to micrometer.
Frame
Ratchet
Locknut
Clamp
Identify the part not belonging to micrometer.
Ratchet
Clamp
O Locknut
Frame
Chapter 11 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 11 - Explain how to use a micrometer to measure cam...Ch. 11 - What is the cylinder taper?Ch. 11 - Describe how to measure main bearing oil...Ch. 11 - Where does maximum cylinder bore wear occur and...Ch. 11 - What type of valve lifter automatically...Ch. 11 - List three types of compression rings.Ch. 11 - Most pistons used today are made of. cast iron...Ch. 11 - Cam bearings in OHV engines are typically which...Ch. 11 - Which of the following is not of concern when...Ch. 11 - True or False? Cylinder taper is the difference in...
Ch. 11 - What is the purpose of a thrust main bearing?Ch. 11 - Each halt' of a split bearing is made slightly...Ch. 11 - Prob. 13RQCh. 11 - Prob. 14RQCh. 11 - Which type of oil ring is slotted so that excess...Ch. 11 - When removing the balance shaft assembly:...Ch. 11 - After installing cam bearings: Technician A checks...Ch. 11 - Technician A says that a cylinder wall with too...Ch. 11 - Technician A uses a pry bar to stretch the timing...Ch. 11 - Technician A installs a cup-type core plug with...Ch. 11 - Technician A uses a micrometer to measure the...Ch. 11 - Technician A says that piston ring end gaps should...Ch. 11 - Technician A checks crankshaft oil clearance with...Ch. 11 - When removing the piston and rod assemblies from a...Ch. 11 - Technician A says that crankshaft counterweights...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- For a measurement that must be made within one ten-thousandth of an inch. Technician A uses a machinists rule. For the same accuracy. Technician B uses a standard micrometer. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTechnician A uses a pry bar to stretch the timing chain onto its sprockets. Technician B cools the timing sprockets so that the timing chain will slip over the teeth. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardq10 Applying finger pressure on the belt near the pulley end is not the correct method to check the tension of the belt drive of a lathe machine. Select one: True Falsearrow_forward
- While inspecting the timing gears of an engine: Technician A says a gear with cracks, spalling, or excessive wear on the tooth surface indicates improper gear backlash. Technician B says the diameter of many of the engines timing gears and sprockets should be measured with the drive chain wrapped around the individual gears. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhile discussing proper band adjustment procedures: Technician A says that on some vehicles the bands can be adjusted externally with a torque wrench. Technician B says that a calibrated inch- pound torque wrench is normally used to tighten the band adjusting bolt to a specified torque. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardDistinguish nominal diameter and gross diameter of boltarrow_forward
- Technician A says that flare nut or line wrenches should be sued to loosen or tighten brake line or tubing fittings Technician B says that open-end wrenches will surround the fitting's nut and provide a positive grip on the fitting. Who is correct? Group of answer choices Technician A only Technician B only Both Technicians A and B Neither A nor Barrow_forwardThe tooth height is defined by the sum of addendum and the dedendum Select one: True Falsearrow_forwardTechnician A says that some small cracks in the accessory drive belt may be within tolerance. Technician B says that serpentine belts can be checked with a wear gauge. Who is correct? Select one: a. Technician A only b. Technician B only C. Both A and B d. Neither A nor Barrow_forward
- Technician A uses a micrometer to measure the connectingrod journal for taper. Technician B uses amicrometer to measure the connecting rod journalfor out-of-roundness. Who is correct?a. Technician Ab. Technician Bc. Both A and Bd. Neither A nor Barrow_forwardTechnician A says that a micrometer can be used to measure the outside diameter of something. Technician B says that a vernier caliper can be used to measure the inside diameter of a bore. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTechnician A says a metric bolt with the marking of 8.9 has more yield strength than a 10.9 bolt. Technician B says only grade 8 nuts should be used on 10.9 rated bolt. Who is correct?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
- Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Mod-01 Lec-16 Basics of Instrumentation; Author: nptelhrd;https://www.youtube.com/watch?v=qbKnW42ZM5c;License: Standard YouTube License, CC-BY