Technician A says that some small cracks in the accessory drive belt may be within tolerance. Technician B says that serpentine belts can be checked with a wear gauge. Who is correct? Select one: a. Technician A only b. Technician B only C. Both A and B d. Neither A nor B

Q: A vehicle has had several radiator replacements, and each time there has been pinhole leaks in the…

A: Solution:

Q: Please select all standard lengths for 3V belts between 76 in and 115 in..   a. 110   b. 90 in.…

A: The effective outside lengths are 76 and 115 in.

Q: When discussing the possible causes for a shudder during acceleration, Technician A says that a worn…

A: Shudder is taken place during acceleration at higher speed. The main reason of this problem is…

Q: Tech A says that camber changes as the suspension moves up and down.  Tech B says that camber…

A: Camber angle : The angle made by the vertical axis with the wheel is known as camber angle . It is…

Q: A technician is inspecting a vehicle and finds the upper radiator hose is collapsed, and the cooling…

A: Given :-  A technician is inspecting a vehicle and finds the upper radiator hose is collapsed, and…

Q: When examining disc brakes: Technician A visually inspects the rotor and says that the rotor can be…

A: Technician A is correct.

Q: The CV joint boots on the left side of a vehicle appear to be squeezed together; the boots on the…

A: The function of engine mounts is to limit the movement of the engine, hold it in a position and…

Q: Technician A says that the piston seal retracts the caliper piston when hydraulic pressure is…

A: Technician A is correct.

Q: While discussing the different types of pressureplates: Technician A says that coil spring types…

A: Option D is the correct naswer

Q: What is the different between on-road bike accommodations and off-road bike accommodations?

A: This question is based on the concept of on road and off road bikes.

Q: 55. The outside edge of the right front tire is worn, but the center and inside edges are almost…

A: We are authorized to answer three subparts at a time since you have not mentioned which part you are…

Q: Interaxle differentials are being discussed. Technician A says the interaxle differential is located…

A: It is an separate differential gear box that locks the first and second differential in a tandem…

Q: What distributed load provides equilibrium? 12 ft. 200 lbs

A: Given that: A distributed load of w and a concentrated beam of 200 lb are applied to the beam. The…

Q: When discussing CV joint diagnosis, Technician A says that the complete failure of a CV joint may…

A: Solution:

Q: While discussing types of coil springs: Technician A says that linear-rate coil springs have equal…

A: Technician A:- Technician A is correct says that in case of linear-rated coil springs have equal…

Q: Which of the following is NOT true about the initial tension in a flat belt drive? OA. It should be…

A: A spherical joint is also known as ball and socket joint, allows three relatives rotation between…

Q: On a banjo type differential, the bearing caps fasten to the removeable center section. True…

A: In a banjo-type differential, the overall design and construction is structured in a specific way to…

Q: Technician A says hypoid gearset are only used in RWD vehicle drivetrains. Technician B says hypoid…

A: Hypoid gear is spiral bevel gear in which the axes doesn't intersect and it is not parallel.  This…

Q: A discussion concerning CV joint testing is being held. Technician A says that a recommended method…

A: CV Joint:  CV joint means Constant Velocity Joint. They are used to transfer the power in a variable…

Q: What may be caused by improper engine and transmission mounts on FWD vehicles?

A: Improper engine and transmission mount can cause unusual vibrations in FWD vehicles.

General safety guidelines

Safety guidelines are the set of rules and codes that must be followed in the workplace for the occupational safety of workers, the machines, and the equipment that are present inside the workshop premise. There are many unsafe conditions and hazardous materials inside the workshop that makes prey for certain risk factors associated with health conditions. Extreme safety precautions must be taken inside the work area just like the precautions and practices that are been followed for Corona Virus Disease 2019 (COVID-19). People can also educate themselves by joining various health programs and camps. These will provide them with the necessary skills and knowledge about safety awareness. Occupational Safety and Health Administration (OSHA) thrives to create a safe and healthy environment for the workers working in the industries and provides them with proper education and training.