Answered: Which of the following would NOT be…

Engineering

Mechanical Engineering

Which of the following would NOT be cause for rejection when checking the tire condition

Automotive Technology

7th Edition

ISBN:9781337794213

Author:ERJAVEC, Jack.

Publisher:ERJAVEC, Jack.

Chapter44: Four- And All-wheel Drive

Section: Chapter Questions

Problem 5MC

See similar textbooks

Related questions

Q: Which of the following statement is correct Select one: Friction causes objects to slip down…

A: Friction force is directly proportional to the normal force acting to body and independent of area…

Q: Road test Report is Overhaul all four-wheel brakes and the Universal joints After the maintenance…

A: Option - B , D => After operation is completed the road test report will happen to check the…

Q: How does cushioning affect the speed of the piston when the cylinder is cushioned at end of the…

A: Cylinder cushioning is a mechanical device that is used to regulate the movement of the piston…

Q: b) If all axles must be operational for the vehicle to function and the reliabilities are measured…

A: In this system it is impossible to run a vehicle without any tire so in this case each tire is in…

Q: Technician A says that flare nut or line wrenches should be sued to loosen or tighten brake line or…

A: Flare nut curench is used for loosening a car's fuel line , brake line ,temperature sensor hollow…

Q: All of the following statements are correct except?a. Tire inflation pressure directly affects…

A: (a) The inflation pressure is directly related to the specific ground pressure. Tire inflation…

Q: frictions doesnot depend on surface area of contact if so,why does a tyre not flat?

A: Friction does not depend on the surface area of contact. It only depends on the weight of the body…

Q: To change tire at intervals of about * 4800 Km for rear 4860 Km for front O 4888 Km for rear 4808 Km…

A: Solution:

Q: Technician A says that on most vehicles, the wheel/tire assembly is considered sprung weight .…

A: technician A is wrong and technician B is saying correctly.

Q: 5 ft 2 ft 7 ft The train has a weight of 23000 Ib and a center of gravity at G. It is suspended from…

A: Free Body Diagram for the given condition can be made as shown below: All normal reactions are…

Q: A P195/75R14 tire classification includes both metric and English standard measurements. True…

A: The standardization of the tires are required because of replacement again and again.

Q: Most vehicles built to use brake on one wheel two wheels only side each wheel O other: tyre in the…

Q: Select all answers that are true concerning pitch-over cycling accidents. Cycling Pitch-over…

Q: What type of tire would result on a higher Rolling Resistance

A: In tires, tread thickness and shape affect the rolling resistance. The thicker and more molded…

Q: An indirect TPMS is being discussed. Technician A says that if a specific tire is low, the system…

A: Indirect TPMS works along with your car's Antilock Braking System's (ABS) wheel speed sensors. If…

Q: When performing the air brake system leakage test, the Certified Inspector must reject the vehicle…

A: Answer = False

Q: A tire that wobbles from side-to-side is said to have -----· a.radial runout b.lateral runout…

A: Given Data : Tire

Q: Consider two infinitely long thin concentric tubes of circular cross section as shown in figure. If…

Q: Replacing the tyre after it burst is example of breakdown maintenance. an Select one: O True O False

A: Breakdown maintenance is an unplanned maintenance which will occur when we are in the situation to…

Q: Which of the following would NOT be cause for rejection when checking the windshield and other…

A: Answer = option (d) The windshield has a 2 inch diameter“star”

Q: what is the formula to measure gas from tire interior?

A: The formula used to measure gas from tire interior is ideal gas law equation. PV=nRT Here, P is the…

Q: A front tire has excessive wear on both edges ofthe tire tread. The most likely cause of this…

A: Given data : Front tire Excessive wear

Q: Technician a says radial ply tires are more rigid in the sidewall area than bias ply tires.…

A: Technician A is wrong because bias-ply tires have fibres of nylon arranged in a diagonal manner to…

Q: A vehicle with a direct TPMS system keeps showing “Low-Left Front Tire,” but when checked, the tire…

A: Direct TPMS. This is often the framework that utilizes sensors on each wheel to degree the tire…

Q: In what direction must the bottom of a tire andwheel assembly be moved to add more positivecamber?

A: Given Data : Bottom of tire Wheel assembly

Q: Which of the following statement is incorrect? Select one: Friction causes objects to move faster…

A: Solution:

Q: During the useful life of a set of new tires (including the spare), it is necessary to rotate them…

A: We will answer the first question since the exact one is not specified. Please submit a new question…

Q: 30. The methods of overhaul differ from maintenance procedure. a. True b. False

A: Note: Since you have asked multiple question, we will solve the first question for you. If you want…

Q: When checking the front end, which of the following are NOT cause for rejection

A: Answer = option (c) All of the statements shown are cause for rejection

Q: What is the principle of the balancing act in tires?

A: The tyre will roll smoothly when all regions of the wheel-tire unit are as evenly weighted as…

Q: what the tire wear pattern will result from excessive negative chamber?

A: Solution:

Q: A tire that wobbles from side-to-side is said to have______ .a. radial runoutb. lateral runoutc.…

A: A tire that wobbles from side to side is said to have lateral runout. When tire is having heavy and…

Q: :In impact testing, we usually have two common Notches used. They are Select one a. V and U b. NONE…

A: Impact testing machines evaluate an object's capacity to face up to high-rate loading and it's…

Concept explainers

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.

Question

100%

Which of the following would NOT be cause for rejection when checking the tire condition?

Any tire has a fabric break or cut exposing ply or cord or any tire is in contact with the body or frame.

Any tire tread or recap is separated or any tire is flat.

All of the statements shown are cause for rejection.

Any tire has any bumps, bulges, or knots or is repaired with a boot or blowout patch.

Expert Solution

Step 1

Answer = option (c)

All of the statements shown are cause for rejection

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Clutches, Brakes, Couplings and Flywheels

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Which of the following statements about sidewall markings is correct? a. The load index is given as a letter. b. The traction and temperature ratings are based on the speed rating of the tire. c. The tires recommended inflation pressure and load are indicated. d. The DOT code indicates when and where the tire was made.
All of the following statements are correct except? a. Tire inflation pressure directly affects traction. b. The recommended tire pressure for front and rear tires may be different. c. The recommended tire pressures are often lower than maximum pressures. d. The recommended tire pressure is molded into the sidewall of the tire.
All of the following statements are correct except? a. Belts are reinforcing materials that encircle the tire under the tread. b. The carcass of a tire is made up of plies, layers of cloth, and rubber. c. Most tread patterns are designed to work well on both wet and dry roads. d. The bead is the decorative pattern at the outer edge of the tread.
A P195/75R14 tire classification includes both metric and English standard measurements. True False
Describe the proper procedure to seal a puncture in a tire.
Technician A says that replacement wheel rims should be the same as the original equipment wheels in load capacity, offset, width, diameter, and mounting configuration. Technician B says that if wheels are installed that have a different stock width or diameter, make sure to use a tire that has the same overall width as the original tires. Otherwise the vehicles wheel-speed sensors, speedometer, antiock brake system, and many other systems will be affected. Who is correct? a. Technician A only b. Technician B only c. Both A and B Neither A nor B
In what direction must the bottom of a tire andwheel assembly be moved to add more positivecamber?
i need the answer quickly
How does a technician determine the proper inflation for a vehicle's tires?
All of the following statements are correct except?a. Tire inflation pressure directly affects traction.b. The recommended tire pressure for front andrear tires may be different.c. The recommended tire pressures are oftenlower than maximum pressures.d. The recommended tire pressure is moldedinto the sidewall of the tire
An indirect TPMS is being discussed. Technician A says that if a specific tire is low, the system will typically alert the driver which tire is low. Technician B says that after serving the indirect TPMS, you need to perform a re-learn procedure. Who is correct? Technician A Technician B Both Technician A and B Neither Technician A or B
A front tire has excessive wear on both edges of the tire tread. The most likely cause of this problem is ______. a. overinflation b. underinflation c. improper static balance d. improper dynamic balance