Words: Boot, Condition, Deformed, Escapes, Heat, Normal, Rubbing Begin CV joint inspection by checking the ________________ of the boots. Splits, cracks, tears, punctures, or thin spots caused by ________________ call for immediate boot replacement. If the boot appears rotted, this indicates improper greasing or excessive ________________ and it should be replaced. Squeeze all boots. If any air ________________, replace the boot. If the inner boot appears to be collapsed or ________________, venting it (allowing air to enter) might solve the problem. Place a round-tipped rod between the ________________ and drive shaft. This equalizes the outside and inside air and allows the boot to return to its ________________ shape.

Q: What is the importance in using a metal as the material for the exhaust gasket? Metal was chosen to…

A:

Q: Surface nonmetallic raceways and their fittings must be designed so that sections can be…

A: Design of surface nonmetallic raceways and their fittings should be such that each section can be…

Q: industrial maintenance What is the most common unsafe act?

A: The most common unsafe acts at the work place are: 1. Nor using the personal protective equipment…

Q: Explain the operation of roll over protection

A: Rollover protection is a structural design that is used to protect the operator of heavy machines.…

Q: A plate boundary with sheer stress is known as _______   a. Divergent   b. Tectonic   c.…

A:

Q: how will a vehicle handle if it has too much toe-out?

A:

Q: Discbrake friction linings are sometimes called brake The ratio of the force required to slide one…

A: Given questions are related to IC engines and Machine design             [Note : According to…

Q: The CV joint boots on the left side of a vehicle appear to be squeezed together; the boots on the…

A: The function of engine mounts is to limit the movement of the engine, hold it in a position and…

Q: All of the following should be done post-repair EXCEPT: Select one: a. go back through the vehicle…

A: The option C is the step that is looked at during the initial phase, not at the time of delivery or…

Q: What happens when the boards are bonded together?

A: When the boards are bonded together with an adhesive material, the mechanical interlocking mechanism…

Q: Explain the features of port and direct injectors and the different testing methods without removing…

A: Port injectors and direct injectors are two types of fuel injectors used in internal combustion…

Q: How did you calculate the local skin friction coefficient

A: The local skin friction coefficient is the component of the drag profile which is the resistant…

Q: Explain the operation of roll over protection systems that are fitted to most modern vehicles. (40 -…

A: Rollover protection systems are safety features installed in vehicles to reduce the risk of injury…

Q: A plate boundary with compressional stress is known as _______   a. Convergent    b. Tectonic…

A: Given Data⇒ Plate boundary compressional stress

Q: What is an additive when referring to lubrication?

A: Lubrication additives are used to enhance the performance of lubricants and functional fluids.A…

Q: Which of the following materials combinations are most likely to fail due to excessive wear in the…

A: 316L Stainless Steel Ultra High Molecular Weight Polyethylene is most likely to fail due to…

Q: For the manufacture of a pipe wrench would you select: a. Fe-0.4%C steel b. Fe-0.4C steel abs case…

A: Pipe wrenches are available in different sizes from 3 inches to 48 inches or larger. A pipe wrench…

Q: how would you make the champhers on a lathe?

A: Chamfer refer to the slope  cut at any right edge of a work piece for example holes, ends of the…

Q: Double cut files use a second set of teeth,perpendicular to the first set to produce a rougher…

A: The given statement is “Double cut files use a second set of teeth perpendicular to the first set to…

Q: Differentiate between Local and Universal Interchangeability?

A: The local and universal interchangeability is given.

Q: J. Pascal's law K. Hygroscopic L DOT wet specification M. DOT dry specification N. Longitudinal…

A: As per the instructions the A-I already answered. Below from J-R matches are explained : J) Pascal's…

General safety guidelines

Safety guidelines are the set of rules and codes that must be followed in the workplace for the occupational safety of workers, the machines, and the equipment that are present inside the workshop premise. There are many unsafe conditions and hazardous materials inside the workshop that makes prey for certain risk factors associated with health conditions. Extreme safety precautions must be taken inside the work area just like the precautions and practices that are been followed for Corona Virus Disease 2019 (COVID-19). People can also educate themselves by joining various health programs and camps. These will provide them with the necessary skills and knowledge about safety awareness. Occupational Safety and Health Administration (OSHA) thrives to create a safe and healthy environment for the workers working in the industries and provides them with proper education and training.