Before use, always inspect the back of a fender cover for:

Q: What is the importance in using a metal as the material for the exhaust gasket? Metal was chosen to…

A:

Q: True or False: The JOIN command requires that line segments must lie end to end with no gaps or…

A: The JOIN command joins similar objects to form a single unbroken object. The JOIN command combines a…

Q: 126) Technician A says all gaskets should be discarded during teardown to keep the work area clean.…

A: According to the technician A , all the gaskets should be discarded during teardown ,it is not…

Q: Explain the operation of roll over protection

A: Rollover protection is a structural design that is used to protect the operator of heavy machines.…

Q: how will a vehicle handle if it has too much toe-out?

A:

Q: Technician A says all gaskets should be discarded during teardown to keep the work area clean.…

A: Gasket : A gasket is a mechanical seal i.e it is used to close up the gap between two mating…

Q: The CV joint boots on the left side of a vehicle appear to be squeezed together; the boots on the…

A: The function of engine mounts is to limit the movement of the engine, hold it in a position and…

Q: When looking to upgrade your gear, what are the top three factors you should keep in mind?

A: To explain: Three factors that should keep in mind while upgrading the gear.

Q: What happens when the boards are bonded together?

A: When the boards are bonded together with an adhesive material, the mechanical interlocking mechanism…

Q: Explain the operation of roll over protection systems that are fitted to most modern vehicles. (40 -…

A: Rollover protection systems are safety features installed in vehicles to reduce the risk of injury…

Q: Worn teeth on a speed gear can cause?

A: worn teeth creates a big problem in gear drive.

Q: to provide a good sealing joint between the cylinder head and exhaust, apply a sealant to the…

A: Question:- To provide a good sealing joint between the cylinder head and exhaust, apply a sealant to…

Q: Which of the following materials combinations are most likely to fail due to excessive wear in the…

A: 316L Stainless Steel Ultra High Molecular Weight Polyethylene is most likely to fail due to…

Q: A kick is defined as an unplanned formation fluid entry into the wellbore annulus. a. True b. False

A: A kick tends to occurs in  oil well when the pressure exerted by the rock surrounding the bore is…

Q: Tech a says, to avoid damage to the spark plug threads of an aluminum head, an anti-seize compound…

A: Tech A is correct as in case of aluminium head it was observed that dissimilar metals goes through…

Q: Words: Boot, Condition, Deformed, Escapes, Heat, Normal, Rubbing Begin CV joint inspection by…

A: Since you have posted a question which have multiple subparts, we will solve first three part for…

Q: Double cut files use a second set of teeth,perpendicular to the first set to produce a rougher…

A: The given statement is “Double cut files use a second set of teeth perpendicular to the first set to…

Q: What are the concerns about dropping an item using a chain in place of a rope?

A: Both the chain drive and belt drives have a separate application, belt, and rope drives will be used…

Q: which best manufaring process use to manufacture carbon steel segment gear?

A: There are so many processes to manufacture segment gear. These are given as, (1) Casting: Sand…

Q: Which tool steel group would be the best for master gauges? D M P S

A: Given :-  Which tool steel group would be the best for master gauges? D M P S

Q: Which of the following would NOT be cause for rejection when checking the windshield and other…

A: Answer = option (d) The windshield has a 2 inch diameter“star”

Q: Tool marks which are produced by force that are parallel to a surface are known as: Group of answer…

A: Tool marks which are produced by force that are parallel to a surface are known as Striated marks.

Q: what can happen when valve spring tension is too low?

A: When the valve paring tension become low, valve springs will become incapable of holding the valve…

Corrosion control methods

Corrosion may be defined as the method in which metals are attacked on their exteriors by gases existing in the atmosphere, converting them to their oxides, nitrides, sulfides, etc.