Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 11, Problem 9RQ
Which of the following is not of concern when checking a piston?
- Diameter
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Why must a cylinder ridge be removed before attempting to remove the piston?
Write a short note any five sections of separator? in oil And gas
When fitting a freshly ground valve into a freshly ground seat: Technician A says that the seat should be ground more with the same stone if the margin is too small. Technician B says that the seat should be ground more with the same stone if the valve seat is too high. Who is correct?
Chapter 11 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 11 - Explain how to use a micrometer to measure cam...Ch. 11 - What is the cylinder taper?Ch. 11 - Describe how to measure main bearing oil...Ch. 11 - Where does maximum cylinder bore wear occur and...Ch. 11 - What type of valve lifter automatically...Ch. 11 - List three types of compression rings.Ch. 11 - Most pistons used today are made of. cast iron...Ch. 11 - Cam bearings in OHV engines are typically which...Ch. 11 - Which of the following is not of concern when...Ch. 11 - True or False? Cylinder taper is the difference in...
Ch. 11 - What is the purpose of a thrust main bearing?Ch. 11 - Each halt' of a split bearing is made slightly...Ch. 11 - Prob. 13RQCh. 11 - Prob. 14RQCh. 11 - Which type of oil ring is slotted so that excess...Ch. 11 - When removing the balance shaft assembly:...Ch. 11 - After installing cam bearings: Technician A checks...Ch. 11 - Technician A says that a cylinder wall with too...Ch. 11 - Technician A uses a pry bar to stretch the timing...Ch. 11 - Technician A installs a cup-type core plug with...Ch. 11 - Technician A uses a micrometer to measure the...Ch. 11 - Technician A says that piston ring end gaps should...Ch. 11 - Technician A checks crankshaft oil clearance with...Ch. 11 - When removing the piston and rod assemblies from a...Ch. 11 - Technician A says that crankshaft counterweights...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Which of the following is not measured with a feeler gauge set? Piston ring side clearance Flywheel runout Crankshaft end play Spark plug gaparrow_forwardTechnician A says that piston ring end gaps should be the same for each ring on a piston. Technician B says that piston ring end gaps should be aligned before installing the piston into its bore. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhat should be done to the valve packing if the valve knob does not turn freely after it has been tightened to stop a leak?arrow_forward
- Technician A says that positive valve stem seals fit tightly around the top of the valve guide. Technician B says that positive stem seals scrape oil off the valve as it moves up and down. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTechnician A says it is not necessary to measure valve stem height unless the valves have been replaced. Technician B says valve stem height can be adjusted with shims. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardto provide a good sealing joint between the cylinder head and exhaust, apply a sealant to the machined surface true or falsearrow_forward
- The spool is sealed along the clearance between moving spool and O housing (valve body) case cylinder O pipearrow_forwardWhich of the following is not true of knurling? It is one of the fastest techniques for restoring the ID dimensions of a worn valve guide. It reduces the amount of work necessary to reseat the valve. It is useful for restoring badly worn guides to their original condition. None of the above.arrow_forwardTechnician A uses a feeler gauge and straightedge to determine the pump cover flatness. Technician B uses an outside micrometer to measure the diameter and thickness of the outer rotor. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Pressure Vessels Introduction; Author: Engineering and Design Solutions;https://www.youtube.com/watch?v=Z1J97IpFc2k;License: Standard youtube license