Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 14, Problem 1ASRQ
Technician A uses a feeler gauge and straightedge to determine the pump cover flatness. Technician B uses an outside micrometer to measure the diameter and thickness of the outer rotor. Who is correct?
- Technician A
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Technician A uses a feeler gauge and straightedge to determine the pump cover flatness.Technician B uses an outside micrometer tomeasure the diameter and thickness of theouter rotor. Who is correct?a. Technician Ab. Technician Bc. Both A and Bd. Neither A nor B
On the low-pressure side of a double diaphragm seal system, the transmitter measures a pressure of 108 in. WC when the tank is empty. Which process should you apply before measuring on the high-pressure side?
Low water level cutoff
Ratholing
Zero suppression
Blowdown
When deciding on the excavator-truck fleet, we should always select the option that ensure that the excavator is never idle.
True
False
Chapter 14 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 14 - What is the most efficient way to increase a...Ch. 14 - True or False? Oil pressure is determined by...Ch. 14 - Describe the simple test used to determine whether...Ch. 14 - Which of the following is a function of the...Ch. 14 - What is ECD and what can result from it?Ch. 14 - True or False? To eliminate the drain of engine...Ch. 14 - For every pound of pressure put on engine coolant,...Ch. 14 - Which is not a typical method of driving the water...Ch. 14 - Which of the following is not an effective way to...Ch. 14 - Explain why a pressure relief valve is needed in...
Ch. 14 - List five problems that can be caused by engine...Ch. 14 - Cooling system hoses should be replaced when they...Ch. 14 - True or False? The presence of air in the cooling...Ch. 14 - Which of the following is not a true statement...Ch. 14 - Describe the procedure for using air bleed valves...Ch. 14 - Technician A uses a feeler gauge and straightedge...Ch. 14 - Technician A says that excessive engine oil...Ch. 14 - While checking for conditions that might cause...Ch. 14 - When installing an oil pump in an engine...Ch. 14 - Technician A says that if the PCV valve or...Ch. 14 - While bleeding air from a cooling system:...Ch. 14 - While diagnosing an engine that overheats after...Ch. 14 - While performing a cooling system service on a...Ch. 14 - While discussing the causes of extreme engine...Ch. 14 - While diagnosing the cause of air bubbles in the...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Technician A uses a feeler gauge and straightedge to determine the pump cover flatness. Technician B uses an outside micrometer to measure the diameter and thickness of the outer rotor. Who is correct? a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forwardTechnician A says that positive valve stem seals fit tightly around the top of the valve guide. Technician B says that positive stem seals scrape oil off the valve as it moves up and down. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhile discussing the results of an oil pressure test: Technician A says that when the fluid pressures are high, internal leaks, a clogged filter, low oil pump out put, or a faulty pressure regulator valve are indicated. Technician B says that if the fluid pressure increased at the wrong time, an internal leak at the servo or clutch seal is indicated. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
- Technician A says it is not necessary to measure valve stem height unless the valves have been replaced. Technician B says valve stem height can be adjusted with shims. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTrue or False? Oil pressure is determined by whether the pump is a gear type or rotor type and by oil clearances, the pumps pressure regulator valve, and oil viscosity.arrow_forwardTrue or False? An oil with the classification of 5W-30 has the viscosity of both a 5- and 30-weight oil. The 5W means the oil has a viscosity of 5 when warm and a 30 rating when it is cold.arrow_forward
- True or False? Oil pressure is determined bywhether the pump is a gear type or rotor typeand by oil clearances, the pump’s pressure regulator valve, and oil viscosity.arrow_forwardWhich of the following is not a type of valve guide seal? Positive Negative Umbrella O-ringarrow_forwardTechnician A says that a brake drum micrometer has pointed anvils. Technician B says that a brake drum micrometer is a large inside micrometer that is read like any other micrometer. Who is correct? Technician A Technician B Both A and B d. Neither A nor Barrow_forward
- Technician A tests brake drums for out-of-round using a dial indicator. Technician B measures the drum diameter in several places to check for out-of-round. Who is correct?arrow_forwardTrue or false Connecting rod in a reciprocating engine is an example for curvilinear translationarrow_forwardWhich of the following is not true of knurling? It is one of the fastest techniques for restoring the ID dimensions of a worn valve guide. It reduces the amount of work necessary to reseat the valve. It is useful for restoring badly worn guides to their original condition. None of the above.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Mod-01 Lec-16 Basics of Instrumentation; Author: nptelhrd;https://www.youtube.com/watch?v=qbKnW42ZM5c;License: Standard YouTube License, CC-BY