Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 14, Problem 7RQ
For every pound of pressure put on engine coolant, the boiling point of the coolant is raised about.
- 2°F(1.1°C)
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Which of the following gasifiers has the
Lowest thermal output?
Entrained flow
O Updraft
Bubbling bed
Downdraft
Choose the correct answer
The suction pressure of a refrigerant
should be as low as possible
The suction pressure of a refrigerant
should be as high as possible
The suction pressure of a refrigerant
should be as constant as possible
None of the above O
After circulating through the engine, the
oil falls back to the oil sump to cool.
Select one:
True
O False
Chapter 14 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 14 - What is the most efficient way to increase a...Ch. 14 - True or False? Oil pressure is determined by...Ch. 14 - Describe the simple test used to determine whether...Ch. 14 - Which of the following is a function of the...Ch. 14 - What is ECD and what can result from it?Ch. 14 - True or False? To eliminate the drain of engine...Ch. 14 - For every pound of pressure put on engine coolant,...Ch. 14 - Which is not a typical method of driving the water...Ch. 14 - Which of the following is not an effective way to...Ch. 14 - Explain why a pressure relief valve is needed in...
Ch. 14 - List five problems that can be caused by engine...Ch. 14 - Cooling system hoses should be replaced when they...Ch. 14 - True or False? The presence of air in the cooling...Ch. 14 - Which of the following is not a true statement...Ch. 14 - Describe the procedure for using air bleed valves...Ch. 14 - Technician A uses a feeler gauge and straightedge...Ch. 14 - Technician A says that excessive engine oil...Ch. 14 - While checking for conditions that might cause...Ch. 14 - When installing an oil pump in an engine...Ch. 14 - Technician A says that if the PCV valve or...Ch. 14 - While bleeding air from a cooling system:...Ch. 14 - While diagnosing an engine that overheats after...Ch. 14 - While performing a cooling system service on a...Ch. 14 - While discussing the causes of extreme engine...Ch. 14 - While diagnosing the cause of air bubbles in the...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- I need the answer as soon as possiblearrow_forwardChoose the correct answer The discharge pressure of a refrigerant should be as constant as possible The discharge pressure of a refrigerant should be as low as possible The discharge pressure of a refrigerant should be as high as possiblearrow_forwardWhat is fan static pressure?arrow_forward
- C- Fill the blank 1- Internal combustion engines classified according to air intake into the cylinder to and-- 2- Typical compression ratio for modern gasoline engine lie between 3- There are a number of gasoline additives that are used to raise the octane number such as 4- Higher compression ratio in SI engine lead to 5- The thermal efficiency of CI engine is than of SI engine. 6- Fuel with octane number of 78 indicate 78%- -and 22%- 7- Anti-Knock quality improves with - no. of carbon atoms. 8- Higher compression ratio in SI engine lead to 9- Maximum power overtaking a vehicle or climbing up a hill (extra load) this requires a mixture.arrow_forwardThe oil sump's small external surface area helps heat transfer from the oil to the outside air. Select one: True Falsearrow_forwardA 2 inch-diameter horizontal jet of water with a velocity of 20 ft/s relative to the ground strikes a flat plate that is attached to a car moving at a velocity of Ve. After it hits, the water splatters in all directions in the plane of the plate. Investigate the effect of the car velocity V. on the force exerted on the plate.arrow_forward
- The boiling point of the coolant in an engines cooling system is raised by the thermostat pressure cap radiator water pumparrow_forwardWhen condenser tubes become fouled, they may be cleaned by A. using a steel brush. B. using a brass brush. C. using a chisel and hammer. D. running a mixture of sand and water through them.arrow_forwardWhich of the following statements is not true about orifice tube systems? The suction line must be cool to the touch from the evaporator outlet to the compressor. The liquid line from the condenser outlet to the evaporator inlet should be cool. The evaporator should feel very cold. The accumulator must be cool to the touch.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Electrical Transformers and Rotating MachinesMechanical EngineeringISBN:9781305494817Author:Stephen L. HermanPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Electrical Transformers and Rotating Machines
Mechanical Engineering
ISBN:9781305494817
Author:Stephen L. Herman
Publisher:Cengage Learning
The Refrigeration Cycle Explained - The Four Major Components; Author: HVAC Know It All;https://www.youtube.com/watch?v=zfciSvOZDUY;License: Standard YouTube License, CC-BY