ENGINEERING CIRCUIT...(LL)>CUSTOM PKG.<
9th Edition
ISBN: 9781260540666
Author: Hayt
Publisher: MCG CUSTOM
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 11, Problem 55E
A load is drawing 10 A rms when connected to a 1200 V rms supply running at 50 Hz. If the source is operating at a lagging PF of 0.9, calculate (a) the peak voltage magnitude; (b) the instantaneous power absorbed by the load at t = 1 ms; (c) the apparent power supplied by the source; (d) the reactive power supplied to the load; (e) the load impedance; and (f) the complex power supplied by the source (in polar form).
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
a) Write down the expression of instantaneous voltage for an AC voltage having a Peak value of 220 Volts and a frequency of 50 Hz provided at time t=0, the instantaneous voltage is 220 Volts. What is the instantaneous voltage of the source at time “t = 5 seconds” What is its RMS voltage?
b) Two 200Ω resistances are connected in series with one 0.5 H Inductance and two 100μF Capacitance with the power supply of part (a).
(i)Draw the circuit diagram of the above network
(ii)What is the total impedance of the circuit
(iii)What is the max current that flows through the Inductance?
(iv)What is the max current that flows through each of the Capacitance? (v)What is the power dissipated in the circuit
(vi)What is the power factor of the circuit
(vii)What is the resonance frequency of the circuit?
(viii) What is the maximum power dissipated by the circuit when it is in resonance
A sinusodial source supplies 30kVAR reactive power to load. Determine the power factor, the apparent power delivered to the load and the RMS voltage.
Need help thanks
Chapter 11 Solutions
ENGINEERING CIRCUIT...(LL)>CUSTOM PKG.<
Ch. 11.1 - A current source of 12 cos 2000t A, a 200 ....Ch. 11.2 - Given the phasor voltage across an impedance ,...Ch. 11.2 - Prob. 3PCh. 11.2 - Prob. 4PCh. 11.2 - A voltage source vs is connected across a 4...Ch. 11.3 - If the 30 mH inductor of Example 11.7 is replaced...Ch. 11.4 - Calculate the effective value of each of the...Ch. 11.5 - For the circuit of Fig. 11.16, determine the power...Ch. 11.6 - Prob. 10PCh. 11 - Prob. 1E
Ch. 11 - Determine the power absorbed at t = 1.5 ms by each...Ch. 11 - Calculate the power absorbed at t = 0, t = 0+, and...Ch. 11 - Three elements are connected in parallel: a 1 k...Ch. 11 - Let is = 4u(t) A in the circuit of Fig. 11.28. (a)...Ch. 11 - Prob. 6ECh. 11 - Assuming no transients are present, calculate the...Ch. 11 - Prob. 8ECh. 11 - Prob. 9ECh. 11 - Prob. 10ECh. 11 - The phasor current I=915mA (corresponding to a...Ch. 11 - A phasor voltage V=10045V (the sinusoid operates...Ch. 11 - Prob. 13ECh. 11 - Prob. 14ECh. 11 - Find the average power for each element in the...Ch. 11 - (a) Calculate the average power absorbed by each...Ch. 11 - Prob. 17ECh. 11 - Prob. 18ECh. 11 - Prob. 19ECh. 11 - The circuit in Fig. 11.36 has a series resistance...Ch. 11 - Prob. 21ECh. 11 - Prob. 22ECh. 11 - Prob. 23ECh. 11 - Prob. 24ECh. 11 - Prob. 25ECh. 11 - Prob. 26ECh. 11 - Prob. 27ECh. 11 - Prob. 28ECh. 11 - Prob. 29ECh. 11 - Prob. 30ECh. 11 - Prob. 31ECh. 11 - Prob. 32ECh. 11 - Prob. 33ECh. 11 - (a) Calculate both the average and rms values of...Ch. 11 - Prob. 35ECh. 11 - FIGURE 11.43 Calculate the power factor of the...Ch. 11 - Prob. 37ECh. 11 - Prob. 38ECh. 11 - Prob. 40ECh. 11 - Prob. 41ECh. 11 - Prob. 42ECh. 11 - Prob. 43ECh. 11 - Compute the complex power S (in polar form) drawn...Ch. 11 - Calculate the apparent power, power factor, and...Ch. 11 - Prob. 46ECh. 11 - Prob. 48ECh. 11 - Prob. 49ECh. 11 - Prob. 50ECh. 11 - Prob. 51ECh. 11 - Prob. 52ECh. 11 - FIGURE 11.49 Instead of including a capacitor as...Ch. 11 - Prob. 54ECh. 11 - A load is drawing 10 A rms when connected to a...Ch. 11 - For the circuit of Fig. 11.50, assume the source...Ch. 11 - Prob. 57ECh. 11 - A source 45 sin 32t V is connected in series with...Ch. 11 - Prob. 60ECh. 11 - FIGURE 11.51 The circuit in Fig. 11.51 uses a Pi...Ch. 11 - Prob. 62ECh. 11 - Prob. 63ECh. 11 - You would like to maximize power transfer to a 50 ...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmaxarrow_forwardLet a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?arrow_forwardA single phase AC chopper supplies a pure inductive load of 0.02H from 220V, 50HZ AC supply. The triggering angle of the thyristors is 100°. (Assume the circuit is ideal.) a. Sketch the circuit b. Develop the load current expression and find the decay angle of the load current c. Sketch the load voltage and load current waveforms d. Calculate the RMS value of load voltage e. Calculate the RMS value of load current f. If the triggering angle of the thyristors is chosen as 60°. Explain the operation of the circuit.arrow_forward
- Please help with the solution.arrow_forwardThe peak amplitude of the sinusoidal voltage source in the circuit shown in the figure is 180 V, a phase of 0 degrees, and its frequency is 5000 rad/s. a)Find VTH and ZTH for the thevenin equivalent circuit. b)Draw the thevenin circuit. c)Calculate the average power delivered to the load (between points a and b) when the load consists of a resistor and capacitor with RL=2000 0 and CL=0.2 uF. d)Determine the settings of RL and CL that will result in the most average power being transferred. e)What is the average power in (c)? Is it greater than the power in (a)? 6 kN 0.6 H a Vg 12 k2 9. +arrow_forwardA 110V(rms), 60HZ AC source is connected to a motor, which can be represented by a resistor and an inductor connected in series. There is also a 56µF capacitor connected across the motor (parallel to the source). Source is providing 1KVA at 73% lagging power factor. Draw a well-labeled circuit diagram and determine: (1) Magnitude of the source Current (ii) Active and reactive power of the motor (iii) Power factor of the motor (iv) Magnitude of the motor current (v) Motor resistor and inductor valuearrow_forward
- a sinusodial source supplies 30 KVAR reactive power to load Z= 250at an angle-75° determine (a) the power factor b) the apparant power delivered to the load and c) the RMS voltage.arrow_forwardA 50 Hz, alternating voltage of 150 V (rms) is applied independently to: (a) resistance of 10 ohms, (b) inductance of 0.2 henry' and (c) capacitance of 50 microfarad. Find the expression of the instantaneous current in each case. Draw the phasor diagram in each case.arrow_forwardThe AC Voltage controller shown below is used for heating a resistive load of 5 Ω and the input voltage Vs = 120 V (rms). The thyristor switch is on for n=125 cycles and is off for m = 75 cycles. Determine the RMS output voltage Vo, the input factor and the average and RMS thyristor currentarrow_forward
- An ac motor with impedance Z, (4.0 A40) O is supplied by an RMS value of 220-V, 60-Hz source. You did Determine the capacitor required to be connected in paralloi with the motor so that the power factor is corrected to unity. The required value of the capacitor is 300 F.arrow_forwardA 10.8-2 resistor, a 11.8-µF capacitor, and a 16.4-mH inductor are connected in series with a 130-V generator. (a) At what frequency is the current a maximum? (b) What is the maximum value of the rms current? Note: The ac current and voltage are rms values and power is an average value unless indicated otherwise. (a) Number i Units (b) Number i Unitsarrow_forwardA 240 volt 60 Hz voltage source is connected to an RLC parallel circuit, the true power is 260 watts. The inductor has a reactive power of 760 VARs, and the capacitor has a reactive power of 360 VARs. a. Find the power factor for this circuit. b. Calculate the capacitance of the capacitor.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Power System Analysis and Design (MindTap Course ...Electrical EngineeringISBN:9781305632134Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. SarmaPublisher:Cengage Learning
Power System Analysis and Design (MindTap Course ...
Electrical Engineering
ISBN:9781305632134
Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma
Publisher:Cengage Learning
02 - Sinusoidal AC Voltage Sources in Circuits, Part 1; Author: Math and Science;https://www.youtube.com/watch?v=8zMiIHVMfaw;License: Standard Youtube License